Emerson Rosemount ET410 Bedienungsanleitung
Quick Start Guide
00825-0100-4212, Rev BA
December 2020
Rosemount™ BP20E Power Module for
Wireless Corrosion Transmitter
NOTICE
This guide provides basic guidelines for the installation of the Rosemount Power Module for the
Rosemount Wireless Permasense Corrosion Transmitter. It does not provide instructions for
configuration, diagnostics, maintenance, service, troubleshooting or intrinsically safe (I.S.)
installations. Refer to the Rosemount Wireless Permasense Corrosion Transmitter Reference Manual
for more instruction. The manual and this guide are also available electronically on Emerson.com
\Permasense.
WARNING
Explosion hazard
Explosions could result in death or serious injury.
Installation of this power module in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Review the Product
Certifications section for any restrictions associated with a safe installation.
Electrostatic hazard
The power module may be replaced in a hazardous area. However, its enclosure has surface resistivity
greater than one gigaohm. Care must be taken during transportation to and from the point of
installation to prevent electrostatic charge build-up.
Physical access
Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end
users’ equipment. This could be intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and fundamental to protecting your
system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for
all systems used within the facility.
CAUTION
Shipping consideration
Each BP20E power module contains two “D” size primary lithium battery. Primary lithium batteries are
regulated in transportation by the U.S. Department of Transportation, and are also covered by IATA
(International Air Transport Association), ICAO (International Civil Aviation Organization), and ARD
(European Ground Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure
compliance with these or any other local requirements. Please consult current regulations and
requirements before shipping
The power module must be installed correctly to avoid risk of becoming detached and falling.
Do not short circuit, recharge, puncture, incinerate, crush, force discharge, expose contents to water
or expose to temperatures above 212 °F (100 °C). Risk of fire or explosion.
Quick Start Guide December 2020
2 Emerson.com/Rosemount
Contents
Overview......................................................................................................................................5
Physical installation...................................................................................................................... 6
Verify operation........................................................................................................................... 8
Disposal/recycling........................................................................................................................9
Product certifications................................................................................................................. 10
December 2020 Quick Start Guide
Quick Start Guide 3
Quick Start Guide December 2020
4 Emerson.com/Rosemount
1 Overview
1.1 Warning on product labels
The Rosemount BP20E Power Module for Wireless Corrosion Transmitters
each have a warning printed on them. In each case the warning text is the
same. Below is a figure that shows the label. The text of the warning is: “Use
only with approved sensor – see instructions. Potential static hazard.”
December 2020 Quick Start Guide
Quick Start Guide 5
2 Physical installation
2.1 Compatibility
Permasense WT100 Corrosion Transmitter
Rosemount Wireless Permasense WT210 Corrosion Transmitter
Rosemount Wireless Permasense ET210 Corrosion Transmitter
Rosemount Wireless Permasense ET310 Corrosion Transmitter
Rosemount Wireless Permasense ET410 Corrosion Transmitter
2.2 Required tooling
Tooling is supplied in the Permasense IK220 Installation Kit:
•Hex key, 2.5 mm, for power module retaining bolts
2.3 Power module installation
To install the power module:
1. Check power module and sensor terminals are clean and corrosion
free.
2. Ensure the ring seal around the connector on the power module is
present.
3. Clip on the power module as shown in Figure 2-1.
4. Fit the two M3 retaining bolts using a 2.5 mm AF hex key.
5. The sensor will resume normal operation. No configuration is
required.
Figure 2-1: Rosemount BP20E Installation
Quick Start Guide December 2020
6 Emerson.com/Rosemount
2.4 Power module removal
To remove the power module:
1. Remove the two M3 retaining bolts using a 2.5 mm AF hex key.
2. Depress the clip on the front of the power module (on the opposite
side to the sensor label).
3. Pull off the power module.
Note
There is a secondary clip mechanism in the electrical connector.
Some force may be required to remove the power module, especially
in cold weather.
4. Dispose of old power module according to local regulations. Refer to
the relevant power module datasheet.
December 2020 Quick Start Guide
Quick Start Guide 7
3 Verify operation
3.1 Sensor operation
Correct sensor operation can be verified by:
•Checking the join status in Gateway Manager software, OR
•Checking in Data Manager that data has been received once the sensor
has joined the gateway.
Quick Start Guide December 2020
8 Emerson.com/Rosemount
4 Disposal/recycling
4.1 Disposing of depleted power modules
1. Dispose in accordance with applicable laws and regulations in your
country and state.
2. Disposal should only be performed by authorized professionals in
accordance with applicable requirements for hazardous waste
transportation and disposal.
3. Incineration should only be performed by trained professionals in
authorized facilities.
4.2 Shipping regulations
Primary lithium batteries are regulated in transportation by the U.S.
Department of Transportation, and are also covered by IATA (International
Air Transport Association), ICAO (International Civil Aviation Organization),
and ARD (European Ground Transportation of Dangerous Goods). It is the
responsibility of the shipper to ensure compliance with these or any other
local requirements. Please consult current regulations and requirements
before shipping.
4.3 Handling considerations
Each power module contains two “D” size primary lithium battery. Under
normal conditions, the battery materials are self-contained and are not
reactive as long as the batteries and the battery pack integrity are
maintained. Care should be taken to prevent thermal, electrical, or
mechanical damage. Contacts should be protected to prevent premature
discharge.
Use caution when handling the power module. It may be damaged if
dropped onto a hard surface. Battery hazards remain when cells are
discharged.
4.4 Environmental considerations
As with any battery, local environmental rules and regulations should be
consulted for proper management of spent batteries. If no specific
requirements exist, recycling through a qualified recycler is encouraged.
Consult the materials safety data sheet for battery specific information.
December 2020 Quick Start Guide
Quick Start Guide 9
5 Product certifications
Rev 0.1
5.1 European Directive information
A copy of the EU Declaration of Conformity can be found at the end of the
Quick Start Guide. The most recent revision of the EU Declaration of
Conformity can be found at Emerson.com/Rosemount.
5.2 Ordinary location certification
As standard, the device has been examined and tested to determine that the
design meets the basic electrical, mechanical, and fire protection
requirements by a nationally recognized test laboratory (NRTL) as accredited
by the Federal Occupational Safety and Health Administration (OSHA).
5.3 North America
The US National Electrical Code® (NEC) and the Canadian Electrical Code
(CEC) permit the use of Division marked equipment in Zones and Zone
marked equipment in Divisions. The markings must be suitable for the area
classification, gas, and temperature class. This information is clearly defined
in the respective codes.
5.4 USA
Certificate: SGSNA/19/BAS/0003
Standards: UL 913 - 8th Edition, Revision Dec 6 2013
Markings: CLASS I, DIV 1, GP ABCD, T4, Tamb = -50 °C to +75 °C, IP67
5.5 Canada
Certificate: SGSNA/19/BAS/0003
Standards: CAN/CSA C22.2 No. 157-92 (R2012) +Upd1 +Upd2
Markings: CLASS I, DIV 1, GP ABCD, T4, Tamb = -50 °C to +75 °C, IP67
5.6 Europe
Certificate: Baseefa18ATEX0144X
Standards: EN IEC 60079-0:2018
EN 60079-11: 2012
Markings: II 1 G, Ex ia IIC T4 Ga, Tamb = -50 °C to +75 °C, IP67
Quick Start Guide December 2020
10 Emerson.com/Rosemount
Andere Handbücher für Rosemount ET410
1
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Emerson Steuereinheit Handbücher
Emerson
Emerson ENARDO 860 Series Bedienungsanleitung
Emerson
Emerson BM6X Series Bedienungsanleitung
Emerson
Emerson OSE Series Bedienungsanleitung
Emerson
Emerson Control Techniques FM-4 Bedienungsanleitung
Emerson
Emerson Keystone 952 Bedienungsanleitung
Emerson
Emerson Fisher EWNS Bedienungsanleitung
Emerson
Emerson SAPAG 8400 Series Technische Daten
Emerson
Emerson Fisher Baumann 24000S Bedienungsanleitung
Emerson
Emerson White Rodgers 36H Series Bedienungsanleitung
Emerson
Emerson Fisher CCV-N Bedienungsanleitung
Emerson
Emerson SEMPELL Kurzanleitung
Emerson
Emerson KEYSTONE F635 Montageanleitung
Emerson
Emerson KEYSTONE V30 Series Betriebsanleitung
Emerson
Emerson Yarway Handbuch
Emerson
Emerson Rosemount RM5800 Bedienungsanleitung
Emerson
Emerson XC1008D Verdrahtungsschema
Emerson
Emerson Keystone PED Kurzanleitung
Emerson
Emerson Spence Type N6 Bedienungsanleitung
Emerson
Emerson COM Express Carrier Leitfaden
Emerson
Emerson ALCO CONTROLS FSE-0 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
