Emerson Rosemount Ultrasonic 3410 Series Bedienungsanleitung

Upgrade kit instructions

00825-0200-3240, Rev AA

February 2022

Rosemount™ Ultrasonic 3410 Series

Electronics

Upgrade kit instructions February 2022

2 3410 Series Electronics Upgrade kit instructions

Signal words and symbols

Pay special attention to the following signal words, safety alert symbols, and statements:

Safety alert symbol

This is a safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

DANGER

Danger indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Warning indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Caution indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

Notice is used to address safety messages or practices not related to personal injury.

Important

Important is a statement the user needs to know and consider.

Tip

Tip provides information or suggestions for improved efficiency or best results.

Note

Note is “general by-the-way” content not essential to the main flow of information.

Contents

Plan..............................................................................................................................................5

Install......................................................................................................................................... 16

Operate......................................................................................................................................31

Mark III Wiring I/O and switch settings........................................................................................44

Communication/Output settings............................................................................................... 52

3410 Communication and Output settings................................................................................ 56

3410 Series engineering drawings..............................................................................................72

February 2022 Upgrade kit instructions

Upgrade kit instructions 3

Upgrade kit instructions February 2022

4 3410 Series Electronics Upgrade kit instructions

1 Plan

1.1 Introduction

1.1.1 General

Welcome to the Rosemount 3410 Series Ultrasonic Retrofit Instruction

Manual.

This manual has been designed to provide you with a step-by-step set of

instructions for retrofitting a Rosemount Gas Ultrasonic meter with Mark III

electronics to the new 3410 Series electronics.

NOTICE

Please read the “Before You Begin” section to make sure you have all the

components necessary to perform the before taking the meter out of

service.

Important

If retrofitting from Mark II electronics to 3410 Series electronics complete

Sections 3 and 4 in the Rosemount Ultrasonic Mark III Upgrade Kit

Instructions to determine the communications and output settings of the

Mark II electronics. Use those settings and the instructions in this manual to

configure the 3410 Series electronics.

1.2 Before you begin

This section shows all of the parts and tools required to perform the

upgrade. Ensure that all of these items are available before taking the Mark

III meter out of service.

1.2.1 Required parts

Ensure that you have received the 3410 Series retrofit components to

upgraderetrofit your meter.

February 2022 Upgrade kit instructions

Upgrade kit instructions 5

1.2.2 Tools required

Figure 1-1: Required Tools

A. ⅛-in. flat-blade screw driver

B. ¼-in. flat-blade screw driver

C. 3/8-in. drive ratchet wrench

D. 3/8-in. drive - extension - at least 3.5-in. long

E. 3/8-in. drive - 7/16-in. socket

F. Allen wrench - size 6 mm (included in Retrofit kit)

G. Crescent wrench for cable glands and electrical conduit

MeterLink™ is required to communicate with the meter electronics, access

information and collect the configuration in the meter and then convert and

download the configuration into the new 3410 Series electronics. Always

use the latest version of MeterLink™. Upgrades to the latest version are

available at: Emerson.com/Rosemount

Upgrade kit instructions February 2022

6 3410 Series Electronics Upgrade kit instructions

1.3 Before removing the Mark III Electronics

1.3.1 Procedure before removing the Mark III Electronics

Procedure

1. Before removing power from the meter being retrofitted software to

connect to the meter.

2. Use the Edit/Compare Configuration screen in MeterLink™

to read the configuration from the meter and save it to a file on your

computer. An example for a file name might be “Meter Name, MkIII

Final Config, 3-4-2013 10-15-02 AM.cfg”. MeterLink will be used later

in this procedure (see Configure the 3410 Series Electronics) to

convert the configuration and download it to the 3410 Series

electronics.

CAUTION

Loss of set-up data

The current meter configuration file must be saved before beginning

the 3410 Series electronics retrofit.

Failure to save the current configuration file can result in the loss of

important set-up data.

3 through 8 provide more detailed instructions on obtaining the

required information with respect to the communications set-up of

the Mark III electronics, however, if these settings are already known,

these steps can be skipped. Step 8 is for Frequency and Diagnostic

outputs. For reference, the known values should be entered in the

Summary table of communications/output settings in

Communication/Output settings. This information will be required in

the setup of the 3410 Series electronics. For any setting which is not

known, the applicable step(s) for obtaining that information can be

used.

3. Use the File|Meter Directory menu path, then select the

<meter name> you want to retrofit.

a) Click the Direct button on the lower left corner of the Meter

Directory dialog box.

b) The Direct Connection Properties For dialog appears.

c) Obtain the Modbus ID (same as Comms Address).

February 2022 Upgrade kit instructions

Upgrade kit instructions 7

Figure 1-2: Accessing Modbus ID for Ports A and B

4. Based on the information contained in the connection properties

window, enter the values for the following parameters in the

Summary table of communications/output settings in

Communication/Output settings:

Port A and B: Modbus ID = _____(enter Comms Address).

5. Exit MeterLink and disconnect your PC from the meter electronics.

The remaining information required before doing the retrofit

upgrade, is based on the wiring terminations and the settings of

various switches on the boards that comprise the electronics.

6. Power down the electronics.

CAUTION

Equipment damage

Remove power from the meter electronics.

Failure to remove power from the meter electronics may result in

damage to the equipment.

7. Remove the end caps from the upper electronics housing of the

meter to access the electronic circuit boards. See Figure 1-4 for

board layout of the 3400 stacks. See Figure 3-4 for the 3410 Series

electronics for board layout.

Upgrade kit instructions February 2022

8 3410 Series Electronics Upgrade kit instructions

Figure 1-3: Remove End Caps from the Upper Electronics

Enclosure

Figure 1-4: 3400 Electronics Assembly board layout

February 2022 Upgrade kit instructions

Upgrade kit instructions 9

Figure 1-5: 3410 Retrofit Electronics Assembly

A. End cap and security screw

B. O-ring

C. Desiccant packet

D. CPU module

E. Optional RS-232 I/O module

F. Optional RS-485 I/O module

G. Blanking cover

H. Guide plate

I. M20 reducer

J. Ground lug - external

K. Transmitter electronics enclosure

L. Power supply

M. I.S. barrier board

N. Standoffs

O. Backplane board

P. O-ring

Q. End cap and security screw

R. O-ring

S. Acquisition cable and roll pin

T. Acquisition module assembly

U. Base enclosure

V. Cable glands

W. Gasket, base enclosure

X. Acquisition cable clamp

Upgrade kit instructions February 2022

10 3410 Series Electronics Upgrade kit instructions

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Steuereinheit Handbücher

Emerson

Emerson HANCOCK Handbuch

Emerson

Emerson Liebert OpenComms SL-19534 Bedienungsanleitung

Emerson

Emerson Asco Bio-Pure Bedienungsanleitung

Emerson

Emerson OSE Series Bedienungsanleitung

Emerson

Emerson Fisher OS2 Bedienungsanleitung

Emerson

Emerson QC54 FOUNDATION Bedienungsanleitung

Emerson

Emerson Sempell series Bedienungsanleitung

Emerson

Emerson Fisher C407-10 Bedienungsanleitung

Emerson

Emerson Bettis TEC2 Bedienungsanleitung

Emerson

Emerson PENBERTHY N6 Series Handbuch

Emerson

Emerson CV4-7 Series Bedienungsanleitung

Emerson

Emerson 740 Series Montageanleitung

Emerson

Emerson Fisher GX Bedienungsanleitung

Emerson

Emerson PACSystems RX3i Bedienungsanleitung

Emerson

Emerson Crosby J Series Bedienungsanleitung

Emerson

Emerson Clarkson ZP300 Bedienungsanleitung

Emerson

Emerson Alco Controls M36 Series Bedienungsanleitung

Emerson

Emerson Fisher V270 Bedienungsanleitung

Emerson

Emerson NEOTECHA SNB Series Bedienungsanleitung

Emerson

Emerson Neotecha NTB Bedienungsanleitung

Emerson

Emerson IC200UEM001 Bedienungsanleitung

Emerson

Emerson Anderson Greenwood 95 Series Bedienungsanleitung

Emerson

Emerson Daniel 700 Series Bedienungsanleitung

Emerson

Emerson KEYSTONE V30 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung