Emerson 818-2050 Installationsanleitung

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: OVERVIEW & OPERATION

CL-RSC Operation

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: GENERAL PARAMETERS

General Parameters

 General parameters are used by techni-

cians and operators to set the control set-

points and defrost schedules.

Before Changing General Parameters

 Before changing parameters, clear any

active alarms by pressing the Alarm Si-

lence button.

Changing General Parameters

 Do not lightly press buttons! You MUST

use considerable force while pressing

controller buttons or your commands

will not register!

 Press (SET) and hold for five seconds.

 If general mode programming has been

password protected, you will see PASS on

the display.

 Press (SET) and use the arrow keys to in-

crement the password number until the

correct password is shown and then press

(SET).

 Note: If general parameters an not pass-

word protected, PASS will not appear on

the display.

The display will show the first programmable

parameter: CSP (Case temperature Set Point).

The arrow keys may be used to scroll through

the list of general parameters. To change the

value of any parameter follow these steps:

1. Select the parameter using the arrow keys

(until the code is shown.

2. Press (SET).

3. Current value of this parameter will display.

Use arrow keys to change values.

4. Press (SET) to accept value.

5. Repeat steps 1-4 until all set points have

been properly configured.

6. When finished, press (SET) again for five

seconds to save changes and exit. The

display will blank for one second and then

revert to normal display if the save was

successful.

7. To cancel all changes, press and hold

(SILENCE) for five seconds, or leave con-

troller idle for 60 seconds. You will lose all

setpoint changes made since you entered

General Programming Mode.

See Warning at right.

SFT

Software Version - - -

WARNING!

You MUST press and hold

(SET) after changing setpoints

for changes to be permanent.

Leaving the controller idle for

60 seconds will log you

out and cancel all your

setpoint changes.

Note! See Technical Information Sheet In This Manual For This Case’s Settings

Note! See Technical Information Sheet In

This Manual For This Case’s Settings

EMERSON CONTROL LINK CPC® P/N818-2050 CONTROLLER: ADVANCED PARAMETERS & ALARMS

Advanced Parameters

 General parameters are used to change

higher-level parameters not directly related to

system operations.

 Selecting and changing advanced parame-

ters works the same way as general parame-

ters, except that they are accessed in a dif-

ferent way and require entering a different

password.

Before Changing Advanced Parameters

 Before changing parameters, clear any ac-

tive alarms by pressing the Alarm Silence

button.

Changing Advanced Parameters

 Do not lightly press buttons! You MUST

use considerable force while pressing

controller buttons or your commands will

not register!

 Press and hold the UP and DOWN buttons

simultaneously for five seconds to enter the

Advance Programming Mode. The display

will show

APAS

 Press (SET) and use the arrow keys to select

the correct password (default is 0000), and

press (SET) to enter it.

Installation Photos

 See next page for installation photos of Emerson Control Link CPC® P/N 818-2050 Refrigeration Controller.

 Note: Exact location may vary depending upon model and features.

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: INSTALLATION PHOTOS

Control Link

Refrigeration System Controller

Ballast

Enlarged View of Control Link

Refrigeration System Controller

Main Power

Switch

Note: This Sheet Applicable

To “CO” Cases Only

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: INSTALLATION PHOTOS

View of Control Link

Refrigeration System

Controller With Housing

Cover Removed

Control Link Refrigeration

System Controller With

Housing Cover Attached

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: INSTALLATION LOCATION

Main Power

Switch

Controller

Box

Controller

Field Wiring

Box

Inhaltsverzeichnis

Andere Emerson Controller Handbücher

Emerson

Emerson Fisher 67D Series Bedienungsanleitung

Emerson

Emerson Fisher S202 Bedienungsanleitung

Emerson

Emerson Asset Management Tag Bedienungsanleitung

Emerson

Emerson Fisher FIELDVUE DVC6200 SIS Bedienungsanleitung

Emerson

Emerson Dixell XRi60CH Verdrahtungsschema

Emerson

Emerson Fisher 67CS Bedienungsanleitung

Emerson

Emerson White-Rodgers 21M51U-843 Bedienungsanleitung

Emerson

Emerson CASH VALVE B Series Handbuch

Emerson

Emerson Dixell XRB06CH Verdrahtungsschema

Emerson

Emerson Fisher 2503 Bedienungsanleitung

Emerson

Emerson Autochangeover Controllers AC8 Bedienungsanleitung

Emerson

Emerson Site Supervisor Bedienungsanleitung

Emerson

Emerson DL8000 Bedienungsanleitung

Emerson

Emerson EZH Series Bedienungsanleitung

Emerson

Emerson Fisher FIELDVUE DVC5000 Konfigurationshandbuch

Emerson

Emerson Fisher FIELDVUE DVC6200 HW2 Konfigurationshandbuch

Emerson

Emerson Biffi Morin Series Bedienungsanleitung

Emerson

Emerson Fisher MR95 Series Bedienungsanleitung

Emerson

Emerson EL-O-Matic F-Series Bedienungsanleitung

Emerson

Emerson Dixell iProChill IPC115D Benutzerhandbuch

Emerson

Emerson FISHER 657 Bedienungsanleitung

Emerson

Emerson Asco 642 Series Bedienungsanleitung

Emerson

Emerson Fisher 656 Bedienungsanleitung

Emerson

Emerson 818-9010 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung