Emerson E2 RX Series Handbuch

026-1622 Rev 0 12-JUN-2012

Operator’s Guide for E2 Refrigeration, BX

HVAC and CX Convenience Store Controllers

Applicable to E2 firmware versions 4.0 and above

Retail Solutions

3240 Town Point Drive NW, Suite 100

Kennesaw, GA 30144, USA

Phone 770-425-2724

Fax 770-425-9319

FCC COMPLIANCE NOTICE

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

CE COMPLIANCE NOTICE

Class A Product Information for E2 Controllers:

The Retail Solutions Einstein and E2 controllers are Class A products. In a domestic

environment this product may cause radio interference in which case the user may be

required to take adequate measures. This covers:

• All E2 family product types: RX - Refrigeration Controller (845-xxxx),

BX - Building/HVAC Controller (845-xxxx), CX- Convenience Store

Controller (845-xxxx), and all version models: (300, 400, 500).

E2 RX/BX/CX Operator’s Guide Manual Table of Contents • v

Table of Contents

1 LOGGING ON AND ACCESS LEVELS.................................................................................................................... 1

2 HOME SCREENS.......................................................................................................................................................... 1

2.1 THE E2 HOME SCREEN.................................................................................................................................................. 1

2.1.1 RX Home Screen ................................................................................................................................................... 1

2.1.2 BX Home Screen ................................................................................................................................................... 2

2.1.3 CX Home Screen ................................................................................................................................................... 2

2.2 SCREEN TYPES............................................................................................................................................................... 3

3 MENUS AND SET UP OPTIONS................................................................................................................................ 5

3.1 MENUS........................................................................................................................................................................... 5

3.2 THE E2 KEYPAD............................................................................................................................................................ 7

3.3 TOGGLING FULL OPTIONS ........................................................................................................................................... 10

3.4 CUSTOMIZING THE HOME SCREEN .............................................................................................................................. 10

3.5 MANUAL DEFROST AND CLEAN MODE....................................................................................................................... 10

3.6 OVERRIDES .................................................................................................................................................................. 11

3.7 ALARMS....................................................................................................................................................................... 12

3.7.1 Accessing the Alarm Advisory Log ...................................................................................................................... 12

3.7.2 Viewing the Controller Advisory Log .................................................................................................................. 12

3.7.3 Date and Time...................................................................................................................................................... 12

3.7.4 State...................................................................................................................................................................... 12

3.7.5 Ack/Reset State..................................................................................................................................................... 12

3.7.6 Area Ctrl: Application: Property......................................................................................................................... 13

3.7.7 Advisory Message ................................................................................................................................................ 13

3.7.8 Acknowledging, Resetting, and Clearing Log Entries......................................................................................... 13

3.7.8.1 Acknowledging......................................................................................................................................................... 13

3.7.8.2 Resetting ................................................................................................................................................................... 13

3.7.8.3 Clearing..................................................................................................................................................................... 13

3.7.9 Facility Status Display (FSD) Alarms ................................................................................................................. 14

4 VIEWING INPUTS AND OUTPUTS........................................................................................................................ 15

4.1 LOCATING LOGGED INPUTS/OUTPUTS......................................................................................................................... 15

4.1.1 Home/Status Screens............................................................................................................................................ 15

4.1.1.1 Setup Screens............................................................................................................................................................ 15

4.1.1.2 Setting Up Input and Output Pointers....................................................................................................................... 15

4.1.2 Log View .............................................................................................................................................................. 16

4.1.3 The Graph View................................................................................................................................................... 17

4.1.4 Zooming In and Out............................................................................................................................................. 17

4.1.5 Checking Boards Online .................................................................................................................................... 17

4.2 CHECKING STATUS SCREENS ...................................................................................................................................... 18

5 NAMING CONVENTIONS FOR E2 CONTROLLERS, APPLICATIONS, AND POINTS .............................. 18

APPENDIX A: TROUBLESHOOTING ................................................................................................................... A-1

The E2 Home Screen Logging On and Access Levels • 1

The Operator's Guide is a general overview of the E2

interface, key pad functionality, menus, and more includ-

ing E2 home screens, logging on, navigation, customizing

the home screen, overrides, and alarms. For more informa-

tion, refer to the complete E2 Manual P/N 026-1614.

1 Logging On and

Access Levels

An E2 may be programmed with up to 25 different

users. A user basically consists of a username, a password,

and an access level. Whenever a username and password

are entered during login, the E2 searches the user records

for the username and password. If found, the E2 will log

the user in at the access level configured for the user in the

user records.

The access level determines how many of the E2’s fea-

tures the user may use. The E2 uses four access levels, one

being the lowest, and four being the highest. Table 1-1

gives a description of each level and the capabilities they

have access to.

Table 1-1 - User Access Levels

Level 1 Read-only access. Users may generally

only view status screens, setpoints, and

some system settings.

Level 2 Setpoint and bypass access. Users may

perform all the tasks a level 1 user may,

and they may also change control setpoints

and bypass some devices.

Level 3 Configuration and override access. Users

may perform all the tasks a level 2 user

may, and they may also override system

settings, create new cells, and program

new applications.

Level 4 System Administrator access. All E2 func-

tions are accessible by a level 4 user.

2 Home Screens

2.1 The E2 Home Screen

The Main Status or Home screen (Figure 2-1 and Fig-

ure 2-2) is divided into sections that display the current

status in areas of importance in the system (i.e., for RX:

suction groups, compressor stages active, circuits, con-

densers, sensor control, and for BX: OAT, demand control,

power monitoring, light schedules, zones, AHUs, and sen-

sor control). Time, date, and alarm status are displayed

along the top of the screen. The display is backlit, but

turns off to save energy after a determined amount of time.

Press any key to bring the display back up.

The Home screen acts as a master and default screen

for all the functions of E2 and can be customized accord-

ing to the user’s needs (see Section 3.5, Manual Defrost

and Clean Mode).

2.1.1 RX Home Screen

Figure 2-1 - RX Home Screen

Advisory Information

Network Information

Controller Information

Suction Groups Section

The first section of the RX Home screen is the Suction

Groups section located in the top left corner. The large let-

ters have the name of Suction Group 1 along with infor-

mation on compressor stages active, and the current

pressure setpoint. Setpoints, status, percentages of capaci-

ties, and which stages are active for each suction group are

displayed as well. The suction group that is displayed in

the large block at the top left of the screen is the group that

is named alphabetically first of the suction groups.

Circuit Status Section

To the right of the Suction Groups section is the Circuit

Status section. Both the Standard Circuits and the Case

Controllers are listed in this screen. The circuit names,

2• E2 RX/BX/CX I&O Manual 026-1622 Rev 0 12-JUN-2012

their current status, and temperatures are listed.

Condenser Section

This section is located at the bottom left of the screen

and contains information on the status of the condenser,

such as the discharge setpoint and individual fan states.

Sensor Control

Below the Circuits section at the bottom right of the

screen is the Sensor Control section where Control Value

and Command information are displayed.

2.1.2 BX Home Screen

Figure 2-2 - BX Home Screen

Function Button Index (5)

Outside Air Temperature

Outside Humidity

Season

Light Level

Demand Control

(FTC)

Power Monitoring

Zones

Sensor Control

Air Handling Units

Light Schedules

14 13

Advisory Information

Network Information

Controller Information

OAT Section

The upper-left hand section of the BX Home screen

contains status information for four different values,

including outside air temperature, humidity percentage,

season, and light level.

Demand Control Section

Directly below the OAT section is demand control sta-

tus information, which shows the number of applications

and number of loads being shed.

Power Monitoring Section

In the lowest left-hand corner of the BX Home screen

is the power monitoring section, containing active KW

and average power information.

Light Schedules Section

In the center of the BX Home screen is ON and OFF

status information for light schedules.

Air Handling Units Section

Located at the top right-hand corner of the BX Home

screen, the AHU section shows the number of AHUs, tem-

perature, state, and ASP information for each.

Zones Section

Directly below the AHU section is the Zones section,

which shows the number of zones, temperature, whether

or not the application is in occupied mode, CSP and HSP.

Sensor Control Section

Sensor Control is at the bottom right-hand corner of

the BX Home screen and contains analog and digital sen-

sors, value, command, and status information.

2.1.3 CX Home Screen

Figure 2-3 - CX Home Screen

HVAC Control

Refrigeration

Lighting

Demand Control

Network Information

Anti-Sweat

Controller Information

Advisory Information Sensor Control

Time Schedules

Lighting Control Section

The lower left-hand corner of the screen shows name

and bypass output for the lighting circuits.

HVAC Control Section

The top left-hand corner of the screen shows whether

the fans are ON or OFF, state, and dehumidification status

of the first two air handlers in the sequence.

Refrigeration Control Section

The top center of the screen shows the name, state, and

current temperature of standard circuits.

Demand Control Section

The top right-hand corner of the screen shows the sta-

tus of the Demand Control application.

Anti-Sweat Control Section

The middle right-hand section of the screen shows

name and percent ON information for each anti-sweat

application.

Screen Types Home Screens • 3

Sensor Control Section

The bottom center section of the screen shows both

analog and digital sensor control, name, and command

output.

Time Schedules Section

The lower right-hand section of the screen shows the

name and current status of time schedules.

2.2 Screen Types

Summary Screens

Summary screens let you view status information for

multiple applications of the same type. For example, (Fig-

ure 2-4) is the Circuits Summary screen in the E2 RX con-

troller. This screen shows the name, state, temperature,

setpoint, alarm, refrigeration, and defrost information for

all defined standard and case control circuits displayed. To

see a more detailed status when on an application sum-

mary screen, highlight the desired application from the list

with the arrow keys and press . This will take you to

the Status screen.

Figure 2-4 - Summary Screen (RX-400 Version Shown)

Status Screens

Status screens are real-time views of application func-

tions. They show the current status of all outputs, the cur-

rent values of all inputs, and other important data such as

control setpoints, run times, and whether or not bypasses

or overrides are active.

Each status screen is specially designed to provide a

concise at-a-glance view of how one or more systems are

functioning.

Figure 2-5 - Status Screen (RX-400 Version Shown)

Setup Screens

The Setup utility is the interface used to change set-

tings and setpoints, and define inputs and outputs in the

E2. Figure 10-11 (section of the E2 manual, P/N 026-

1614) shows a typical Setup screen and its primary ele-

ments.

Index Tabs:

Figure 2-6 - Index Tabs (RX-400 Version Shown)

The 10 boxes at the top of the screen labeled C1

through C0 are known as the index tabs. These tabs pro-

vide you with a short index of the screens that are used to

set up an application. C1 through C0 represent the screen

numbers (C1 being screen 1, C2 being screen 2, and so

on.) Press the key and the number of the index tab

(next to the C) and the cursor highlights that index tab.

Each of the Setup screens that you may access will

have a name beside its number. In Figure 10-11, for exam-

ple, you will notice some tabs have names, while others

are blank. This is because there are only four screens in the

Setup for this particular application; C3 is not an accessi-

ble screen.

There are several reasons why a tab may be inaccessi-

ble (i.e., without a name next to the number):

• The tab (and the corresponding screen) is unused

and reserved for later revisions.

• The screen may only be accessed when running in

Full Options mode (see Section 3.4, Customizing

the Home Screen).

4• E2 RX/BX/CX I&O Manual 026-1622 Rev 0 12-JUN-2012

• The screen may require one or more fields to be set

to certain values before the screen may be accessed.

For example, a screen containing nothing but com-

pressor proof input definitions might be hidden if

there is a field on another screen that tells the sys-

tem there are no proof checking devices on the

group’s compressors. To access this screen, you

would have to set this field to YES.

The screen you are currently in is always highlighted

in the screen’s index tab. For example, because Screen 1 is

displayed, tab C1 is highlighted.

As you move to other screens within Setup, the high-

light will move to different tabs to indicate which screen

will be displayed.

Header Icons:

Figure 2-7 - Header Icons

At the very top of every screen in the E2, there are

icons that indicate various stages of activity, number of

users logged into the controller, battery alerts, connectivity

status, and more.

Table 2-1 - Header Icons and Descriptions

Icon Description

Single user is logged in

Multi-users are logged in

Terminal mode in use

E2 is connected to Ethernet

Wait, or system is busy

Disk activity, or saving to disk

Caps lock is ON

Figure 2-8 - Setup Screen (RX-400 Version Shown)

Andere Handbücher für E2 RX Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Emerson Controller Handbücher

Emerson

Emerson NZ Series Bedienungsanleitung

Emerson

Emerson Fisher 2503 Bedienungsanleitung

Emerson

Emerson Dixell IEV12D Verdrahtungsschema

Emerson

Emerson Bettis G Series Bedienungsanleitung

Emerson

Emerson Fisher FIELDVUE DVC6200 SIS Bedienungsanleitung

Emerson

Emerson Bettis RP3E Bedienungsanleitung

Emerson

Emerson Fisher 4194HA Bedienungsanleitung

Emerson

Emerson Dixell XR70CH Verdrahtungsschema

Emerson

Emerson Unidrive M702 Bedienungsanleitung

Emerson

Emerson EIM 2000 Series Bedienungsanleitung

Emerson

Emerson Dixell XR30CX-4S1C1 Verdrahtungsschema

Emerson

Emerson Digitax ST Bedienungsanleitung

Emerson

Emerson DIXELL iCHILL IC100D EVO Bedienungsanleitung

Emerson

Emerson Fisher 480 Series Bedienungsanleitung

Emerson

Emerson Fisher Level-Trol 2502 Series Bedienungsanleitung

Emerson

Emerson PaCSystems VersaMax Series Bedienungsanleitung

Emerson

Emerson Bettis GVO-C Series Bedienungsanleitung

Emerson

Emerson Yarway Integral Strainerimpulse 400 Series Bedienungs- und Wartungshandbuch

Emerson

Emerson Fisher 630 Series Bedienungsanleitung

Emerson

Emerson Dixell XR75CX Series Bedienungsanleitung

Emerson

Emerson S402Y Bedienungsanleitung

Emerson

Emerson Sempell series Bedienungsanleitung

Emerson

Emerson Fisher 3024S Bedienungsanleitung

Emerson

Emerson MultiFlex RTU Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung