Emerson Rosemount 2110 Bedienungsanleitung

Quick Start Guide

00825-0100-4029, Rev CC

March 2022

Rosemount™ 2110 Level Switch

Vibrating Fork

Contents

About this guide...........................................................................................................................3

Installation................................................................................................................................... 5

Prepare the electrical connections..............................................................................................10

Connect wiring and power up.....................................................................................................18

Product certifications................................................................................................................. 21

Quick Start Guide March 2022

2 Rosemount 2110 Level Switch

1 About this guide

This Quick Start Guide provides basic guidelines for the Rosemount 2110.

Refer to the Rosemount 2110 Reference Manual for more instructions. The

manual and this guide are also available electronically at

Emerson.com/Rosemount.

1.1 Safety messages

WARNING

Failure to follow safe installation and servicing guidelines could result in

death or serious injury.

Ensure the level switch is installed by qualified personnel and in accordance

with applicable code of practice.

Use the level switch only as specified in this manual. Failure to do so may

impair the protection provided by the level switch.

Repair, e.g. substitution of components, etc. may jeopardize safety and is

under no circumstances allowed.

WARNING

Explosions could result in death or serious injury.

The level switch must only be installed and operated in non-hazardous

(ordinary) locations.

WARNING

Electrical shock could cause death or serious injury.

Ensure the power to the level switch is off, and the lines to any other external

power source are disconnected or not powered while wiring the level switch.

Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

Ensure the wiring is suitable for the electrical current and the insulation is

suitable for the voltage, temperature, and environment.

March 2022 Quick Start Guide

Quick Start Guide 3

WARNING

Process leaks could result in death or serious injury.

Ensure the level switch is handled carefully. If the process seal is damaged,

gas might escape from the vessel (tank) or pipe.

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/or

misconfiguration of end users’ equipment. This could be intentional or

unintentional and needs to be protected against.

Physical security is an important part of any security program and

fundamental to protecting your system. Restrict physical access by

unauthorized personnel to protect end users’ assets. This is true for all

systems used within the facility.

CAUTION

Hot surfaces

The flange and process seal may be hot at high process temperatures. Allow

to cool before servicing.

Quick Start Guide March 2022

4 Rosemount 2110 Level Switch

2 Installation

2.1 Fork alignment in a pipe installation

The fork is correctly aligned by positioning the groove or notch as indicated

(Figure 2-1).

Figure 2-1: Correct Fork Alignment for Pipe Installation

A. Tri Clamp process connections have a circular notch

B. Threaded process connections have a groove

2.2 Fork alignment in a vessel (tank) installation

The fork is correctly aligned by positioning the groove or notch as indicated

(Figure 2-2).

Figure 2-2: Correct Fork Alignment for Vessel (Tank) Installation

OKOK

OK OK

A. Tri Clamp process connections have a circular notch

B. Threaded process connections have a groove

March 2022 Quick Start Guide

Quick Start Guide 5

2.3 Mounting the threaded version

2.3.1 Threaded vessel (tank) or pipework connection

Procedure

1. Seal and protect the threads. Use anti-seize paste or PTFE tape

according to site procedures.

A gasket may be used as a sealant for BSPP (G) threaded connections.

2. Screw the level switch into the process connection.

Note

Tighten using the hexagon nut only.

Figure 2-3: Vertical Installation

A. Gasket for BSPP (G) threaded connection

Figure 2-4: Horizontal Installation

A. Gasket for BSPP (G) threaded connection

Quick Start Guide March 2022

6 Rosemount 2110 Level Switch

2.3.2 Threaded flange connection

Procedure

1. Place the customer-supplied flange and gasket on the vessel (tank)

nozzle.

A. Gasket (customer supplied)

2. Tighten the bolts and nuts with sufficient torque for the flange and

gasket.

3. Seal and protect the threads. Use anti-seize paste or PTFE tape

according to site procedures.

A gasket may be used as a sealant for BSPP (G) threaded connections.

March 2022 Quick Start Guide

Quick Start Guide 7

4. Screw the level switch into the flange thread.

Note

Tighten using the hexagon nut only.

A. Gasket for BSPP (G) threaded connection

Quick Start Guide March 2022

8 Rosemount 2110 Level Switch

2.4 Mounting the Tri Clamp version

Procedure

1. Lower the level switch into the flange face.

A. Seal (supplied with Tri Clamp)

2. Fit the Tri Clamp.

Note

The Tri Clamp and seal are supplied in an accessory kit that has to be

ordered separately. See the Rosemount 2110 Product Data Sheet for

ordering information.

March 2022 Quick Start Guide

Quick Start Guide 9

3 Prepare the electrical connections

3.1 Cable selection

Twisted-pairs and shielded wiring is recommended for environments with

high EMI (electromagnetic interference). Two wires can be safely connected

to each terminal screw. Maximum wire size is 15 AWG.

3.2 Cable glands/conduits

The cable gland is integrated in the four-position plug of the level switch. Do

not make any modifications to the level switch.

3.3 Electronics options

Figure 3-1: Direct Load Switching – Electronics Option Code 0

0V/N

+V/L

Load

Table 3-1: Electrical Parameters – Electronics Option Code 0

Parameter Value

Load switching ac/dc

Direct load switching ac/dc

Maximum switched load 500 mA

Maximum peak load 5 A for 40 ms maximum

Minimum switched load 20 mA continuous

Voltage drop 6.5 V @ 24 Vdc or 5 V @ 240 Vac

Current draw (load off) < 3 mA continuous

Quick Start Guide March 2022

10 Rosemount 2110 Level Switch

Andere Handbücher für Rosemount 2110

Inhaltsverzeichnis

Andere Emerson Schalten Handbücher

Emerson

Emerson Topworx Valvetop DXN Gebrauchsanweisung

Emerson

Emerson AVOCENT Montage- und Wartungsanleitung

Emerson

Emerson Rosemount 2160 Bedienungsanleitung

Emerson

Emerson Rosemount 2130 Bedienungsanleitung

Emerson

Emerson Rosemount 2110 Bedienungsanleitung

Emerson

Emerson AVOCENT Bedienungsanleitung

Emerson

Emerson Cybex SC KM 140 Bedienungsanleitung

Emerson

Emerson ASCO 7000 Series Bedienungsanleitung

Emerson

Emerson Rosemount 2110 Bedienungsanleitung

Emerson

Emerson Fisher GH04148 Bedienungsanleitung

Emerson

Emerson Rosemount 2460 Bedienungsanleitung

Emerson

Emerson PACSystems SLM042 Bedienungsanleitung

Emerson

Emerson Rosemount 2120 Bedienungsanleitung

Emerson

Emerson Rosemount 2460 Bedienungsanleitung

Emerson

Emerson AVOCENT Bedienungsanleitung

Emerson

Emerson DWM COPELAND OPS2 Handbuch

Emerson

Emerson Rosemount FS-IR-975 Bedienungsanleitung

Emerson

Emerson Rosemount 2160 Bedienungsanleitung

Emerson

Emerson Rosemount 2120 Bedienungsanleitung

Emerson

Emerson Rosemount 585 Annubar Bedienungsanleitung

Emerson

Emerson ASCO 7000 Series Bedienungsanleitung

Emerson

Emerson LRA185KMM Bedienungsanleitung

Emerson

Emerson SmartSwitch Bedienungsanleitung

Emerson

Emerson SC 820 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung