Emerson Inspire 1HDEZ-1521 Bedienungsanleitung

TROUBLESHOOTING

1HDEZ-1521

Emerson Inspire™

Thermostat/Interface Equipment Control

Installation Instructions

ATTENTION: MERCURY NOTICE

This product does not contain mercury. However, this product may replace

a product that contains mercury.

Mercury and products containing mercury must not be discarded in

household trash. Do not touch any spilled mercury.Wearing non-absorbent

gloves, clean up any spilled mercury and place in a sealed container. For

proper disposal of a product containing mercury or a sealed container of

spilled mercury, place it in a suitable shipping container. Refer to www.

thermostat-recycle.org for location to send product containing mercury.

FAILURETO READAND FOLLOWALL INSTRUCTIONSCAREFULLY BEFORE

INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL

INJURY AND/OR PROPERTY DAMAGE.

Thermostat installation and all components of the control system shall

conform to Class II circuits per the NEC code.

WARNING

To prevent electrical shock and/or equipment damage, disconnect

electric power to system at main fuse or circuit breaker box until

installation is complete.

CAUTION

Index Page

Applications and Specications 3

Installation 4

Advanced Installer Menu 12

Main Menu 20

Troubleshooting 26

APPLICATIONS

& SPECIFICATIONS

Applications and Speci cations

Electrical Rating:

Input-Hardwire.............................. 20 to 30 VAC

Terminal Load ............................... 1.0A per terminal, 2.5A maximum

all terminals combined

Setpoint Range ............................. 45° to 99°F (7° to 37°C)

Di erential (Single Stage) ............. Heat 0.6°F; Cool 1.2°F

Di erential (Multi-Stage) .............. Heat 0.6°F; Cool 1.2°F

Di erential (Heat Pump) ............... Heat 1.2°F; Cool 1.2°F

Operating Ambient ....................... 32°F to +105°F (0° to +41°C)

Operating Humidity ...................... 90% non-condensing max.

Shipping Temperature Range ........ -40° to +150°F (-40° to +65°C)

Dimensions Interface .................... 3-1/4"H x 6-1/8"W x 5/8"D

Dimensions Control....................... 5-1/2"H x 5-3/4"W x 1-1/2"D

Con guration

Options

Applications Maximum

Stages

Single Stage Gas, Oil, Electric, Heat Only, Cool Only or

Heat Cool Systems 1/1

Multi Stage Gas, Oil, Electric, Heat Only, Cool Only or

Heat Cool Systems 2/2

Heat Pump Single or Two Compressor Systems with up

to 2Stages of Aux / Em Heat 4/2

Heat Pump

with Dual Fuel

Single or Two Compressor Systems with up

to 2Stages of Fossil fuel Heat 4/2

INSTALLATION

Installation

Reduce installation time with a USB

1. Go to www.white-rodgers.com

2. Enter 1HDEZ-1521 in the Model

Number Search  eld

3. Select the link for the USB download

tool and follow instructions

Upload pre-con gured thermostat

settings for every job!

Create custom messages for your rou-

tine maintenance and service calls!

INSTALLATION

Equipment Control

Mount on wall or exterior surface of HVAC equipment. Control has four

mounting holes. Wall anchors and screws are provided for mounting on dry-

wall. Drill 3/16"hole for drywall mounting.

If mounting on equipment Do Not Mount inside HVAC equipment.

Only mount on outside of HVAC equipment.

Gas Furnace Equipment

Retur

n Air Duct

Supply

Duct

Equipment Control

Module

Installation

INSTALLATION

Equipment Control Terminals Operation / Function

R................................................ 24 VAC Transformer

RC.............................................. 24 VAC Cooling Transformer*

RH ............................................. 24 VAC Heating Transformer*

C................................................ 24 V Transformer Common

W/E............................................ Heating Stage 1 HP Aux/Em Heat Stage 1

W2............................................. Heating Stage 2 HP Aux/Em Heat Stage 2

Y................................................ Compressor Stage 1

Y2.............................................. Compressor Stage 2

G................................................ Fan Relay

L Terminal .................................. System Monitor Compatible with

Comfort Alert Diagnostics

O/B Terminal .............................. Changeover Relay Heat Pump

DHM .......................................... Dehumidication Relay / Connection

DHM2........................................ Dehumidication Relay / Connection

HM............................................. Humidication Relay / Connection

HM2........................................... Humidication Relay / Connection

R................................................ 24 VAC to Interface

1................................................. Data to/from Interface

2................................................. Data to/from Interface

C................................................ 24 VAC Common to Interface

RJ11 ........................................... Field conguration hook-up with RJ11

equipped conguration tool

+................................................. Voltage to Outdoor Sensor

S................................................ Outdoor Sensor Temperature Signal

-................................................. Voltage to Outdoor Sensor

Installation

*For 2 transformer systems, cut and tape o one transformer. If transformer

safety circuits are only in one of the systems, remove the transformer of the

system with NO safety circuits. If required, replace remaining transformer

with a 75 VA Class II transformer. After disconnecting one transformer, the

two commons must be jumpered together.

INSTALLATION

RJ-11 Connection for

Conﬁguration Plug-In tool

Status/Fault

7-Segment LED

Wiring to

Thermostat

R and C from HVAC

terminal strip or

system transformer

Wiring to

Sensor

Wiring to

indoor/outdoor

equipment

W/E

O/B

HM2

DHM

DHM2

LED push

button switch

Wiring to

humidiﬁcation

equipment

Wiring to

dehumidiﬁcation

equipment

DHM switch*

HM switch*

* To use the HVAC transformer to power humidication/dehumidication

switch HM/DHM switches to “SYS” position:

– Connect humidier to HM

– Connect dehumidier to DHM

If humidier or dehumidier have a separate transformer, switch HM or

DHM switch to “DRY” position:

– Connect humidier to HM and HM2 (or)

– Connect dehumidier to DHM and DHM2

Installation

INSTALLATION

Installation

Fig. 1- Typical Connection of a Single Stage or Multi-Stage System

*Factory installed jumper between RH and RC

SYSTEM R RH RC C W/E W2YY2G O/B L

Single

Stage

24 VAC

Power

24 VAC

Power for

Heating

24 VAC

Power

for Cooling 24 VAC

Common

Required

Heat N/A Cool N/A Fan N/A System

Monitor

Multi

Stage

24 VAC

Power

24 VAC

Power

24 VAC

Power

Heat

mode

stage

Heat

mode

stage

Cool

mode

stage

Cool

mode

stage

CLASS II

Transformer

120 VAC

NEUTRAL

24 VAC

HOT

SYSTEM R RH RC C W/E W2YY2G O/B L

Heat

Pump

24 VAC

Power

24 VAC

Power for

Heating

24 VAC

Power

for Cooling 24 VAC

Common

Required

Aux /

Stage

Aux /

Stage

Com-

pres-

sor

Stage

Com-

pres-

sor

Fan Change-

over

Valve

System

Monitor

CLASS II

Transformer

120 VAC

NEUTRAL

24 VAC

HOT

Fig. 2- Typical Connection of Heat Pump System up to 4Stages

Heat/2Stages Cool

*Factory installed jumper between RH and RC

Note: Dual fuel systems W/E is fossil fuel 1st stage and W2is fossil fuel 2nd stage.

INSTALLATION

Installation

Wiring Guide for Equipment Accessories

HM2

Non-Powered

Humidier

Transformer

HM DRY

RH HM2

Fig. 3 - Humidier. HM terminal provides system 24V on call for humidication

Fig. 4 - Powered Humidier. With HM DRY switch in HM2position, HM

and HM2provide normally open dry contact for low voltage (24V) powered

humidier connection.

HM2

Non-Powered

Humidier

HM DRY

RH HM2

Fig. 5 - Powered Dehumidier. With DHM DRY switch in DHM2position,

DHM and DHM2provide normally open dry contact for low voltage (24V)

whole house powered dehumidier connection.

DHM

DHM2

Powered

Dehumidier

DHM DRY

RH DHM2

INSTALLATION

Installation

Fig. 6 - System Dehumidication with variable speed blower. For systems

where low speed requires connect to normally open 24V powered DHM

terminal for low speed connection on air handler/furnace (24V removed

on dehumidication call).

Wiring Guide for Equipment Accessories

DHM

DHM2

Low Speed

Fan

Transformer

DHM DRY

RH DHM2

Fig. 7 - System Dehumidication with variable speed blower. For systems

where low speed requires system 24V on dehumidification connect 24V

to DHM2with DHM DRY switch in DHM2position and connect DHM

to low speed connection on air handler/ furnace.

DHM

DHM2

Low Speed

Fan

DHM DRY

RH DHM2

Andere Handbücher für Inspire 1HDEZ-1521

Inhaltsverzeichnis

Andere Emerson Thermostat Handbücher

Emerson

Emerson Dixell XR35CX - 110VAC Bedienungsanleitung

Emerson

Emerson White Rodgers 1H11G-101 Bedienungsanleitung

Emerson

Emerson White-Rodgers P210 Bedienungsanleitung

Emerson

Emerson 80 Series Bedienungsanleitung

Emerson

Emerson 0037-7303A Bedienungsanleitung

Emerson

Emerson FG Produkthandbuch

Emerson

Emerson 1F78 Bedienungsanleitung

Emerson

Emerson White Rodgers 1E30N-910 Bedienungsanleitung

Emerson

Emerson Sensi Bedienungsanleitung

Emerson

Emerson Sensi Touch Bedienungsanleitung

Emerson

Emerson 1F86ST-0471 Bedienungsanleitung

Emerson

Emerson 1F95-1291 Bedienungsanleitung

Emerson

Emerson Delwarva Power Web-Programmable Thermostat Bedienungsanleitung

Emerson

Emerson Sensi 1F87U-42WF Installationsanleitung

Emerson

Emerson White-Rodgers 1F75H-21NP Bedienungsanleitung

Emerson

Emerson 1F85U-22NP Bedienungsanleitung

Emerson

Emerson White Rodgers 1F87-361 Bedienungsanleitung

Emerson

Emerson VERDANT VX Series Bedienungsanleitung

Emerson

Emerson 1F86-0471 Bedienungsanleitung

Emerson

Emerson 99 Bedienungsanleitung

Emerson

Emerson Lumity Wireless Touchscreen RTU Thermostat Bedienungsanleitung

Emerson

Emerson Sensi Touch Wi-Fi Thermostat Bedienungsanleitung

Emerson

Emerson Sensi Bedienungsanleitung

Emerson

Emerson 7903 Betriebsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung