Emerson Liebert GXT3 6000VA RTL630 Bedienungsanleitung

1 SL-23185QS6L630_Rev0_09-2012

Liebert®GXT3™

Quick Start Guide –6000VA RTL630 Models

The Liebert GXT3 is shipped with the following items:

•Terminal Block Communication terminals

•Compact disc with:

oLiebert MultiLink®

oConfiguration program

oUser manual (electronic version)

•USB cable, one; 2m (6-1/2 ft.) long

•Rack handles with mounting hardware

•Plastic tower support base, one set

•Plastic Bezel

•Warnings, safety instructions booklet and WEEE recycling sheet (ISO 14001 compliance)

If the UPS is intended to be installed in the Tower orientation, locate the support base and spacers then assemble the two

stand assemblies with an even number of spacers in each assembly. Insert the UPS between the support base

assemblies with adequate space between the assemblies as shown in the picture below. Note the display should be

located on the upper half of the unit in the Tower orientation. To rotate the display with the bezels removed, depress the

grooved tabs on the sides and rotate it 90 degrees clockwise. If the USP is to be installed in a rack enclosure, follow the

instructions provided with the rack mounting hardware for proper installation.

The UPS is cord and plug connected using a L6-30P input plug. All wiring should be done in accordance to all local and

national electrical codes.

The UPS is equipped with output receptacles; connect the equipment to be protected to the output receptacles.

The GXT3-6000RTL630 is compatible with IT Power Systems. To configure the unit for operation on the IT Power

system, remove the 2 screws securing the cover plate in the lower right hand side on the rear of the unit and disconnect

the jumper, then replace the cover and secure with the screws.

IT Power System

Connector

(with cover removed)

DISCONTINUED

2 SL-23185QS6L630_Rev0_09-2012

The Liebert®GXT3™6000 VA models ship without the internal battery installed. Located the internal battery kit, model

number GXT3-240BATKIT, and follow these steps to install the battery.

1. Loosen and remove the screws on the battery door and remove the battery door and set aside the screws and

door for reassembly

2. Insert the two battery trays and connect the plugs to the mating receptacles

3. Gently push the battery wiring into the compartment making sure that the wiring will not be pinched when the

battery door is reinstalled.

4. Reinstall the battery door and secure using the screws that were removed in step 1.

5. Locate the plastic bezel from the shipping box and attach the bezel to the UPS taking care to align the fastening

clips on both ends before inserting them into the holes.

6. If your application requires the use of external battery cabinets for longer back up time requirements, connect the

first battery cabinet to the UPS with the cable provided with the battery cabinet. Note: it does not matter which

connector is used on the battery cabinet. If more than one battery cabinet is used the additional cabinets then

connect to the adjoining battery cabinet.

IT Power System

Access Cover

External Battery

Cabinet Connector

for

GXT3-240VBATTUL

Input Circuit Breaker

Maintenance

Bypass Breaker

Output Circuit Breakers

Battery Kit Handle

Internal Battery Kit

(1 of 2)

GXT3-240BATBKIT

Liebert GXT3 UPS

GXT3-6000RTL630

DISCONTINUED

3 SL-23185QS6L630_Rev0_09-2012

The Liebert®GXT3™UPS is ready to be powered.

1. Ensure the maintenance bypass breaker is in the open position and that the guard is secured in place.

2. Ensure that the REPO connector on the rear of the unit has a jumper between pins 1-2 of the REPO connector or

properly wired to an Emergency Power Off circuit (normally closed).

3. Install any optional Intellislot communication card into the Intellislot port on the rear of the unit.

4. Close the input breaker in the panelboard that provides input power to the UPS

5. Close the input breaker on the rear of the UPS unit. Note: the UPS will now have power and the AC Input

indicator on the display should illuminate. The UPS will also begin to charge the internal batteries at this point, so

there will also be battery capacity LEDs illuminated.

6. The Liebert GXT3 UPS has customizable settings that might be required depending on the application. Please

review the CD that ships with the UPS unit for the steps to use the configuration program and make any

necessary changes. Once that is complete, proceed to the next step.

7. Close all output breakers on the rear of the UPS

8. If external battery cabinets are used, close all breakers on the rear of each battery cabinet

9. Press and hold for about 4 seconds, the “ON” button on the UPS display. Note: this will apply power to the output

receptacles via the internal bypass and the bypass indicator will be illuminated along with an audible beep.

10. Over the next several seconds the UPS will perform the self checks and startup routine then automatically

transfer the connected equipment to the inverter power. Once that is complete, the bypass indicator will turn off

and the inverter indicator will illuminate.

The UPS is now running in normal operation mode providing protected, filtered power to the connected equipment.

6000VA

DISCONTINUED

4 SL-23185QS6L630_Rev0_09-2012

Troubleshooting

The following symptoms indicate the Liebert®GXT3™is malfunctioning:

•The relative indicators illuminate, indicating the UPS has detected a problem.

•An alarm buzzer sounds, alerting the user that the UPS requires attention.

In addition to the fault indicator being illuminated, one or more of LED segments of battery level indicator will also be

illuminated to provide a diagnostic aid to the user, as shown below

The descriptions are listed in the following table

Indicator

Diagnosis/Audible alarm

A - E

On bypass from output overload (half-second beep every half-second)

On bypass due to over temperature condition (1-second beep every 4 seconds)

On bypass due to DC bus overvoltage (1-second beep every 4 seconds)

On bypass due to DC/DC power supply failure (1-second beep every 4 seconds)

PFC failure (1-second beep every 4 seconds)

On bypass due to inverter failure (1-second beep every 4 seconds)

A&B

UPS Failure (includes dual-fan failure, single-fan failure under certain conditions and

battery charger failure) and continuous alarm

A&C

UPS failed battery test (2-second beep every 60 seconds)

A&D

Maintenance bypass switch on (continuous)

A&E

Bypass feedback (1-second beep every 4 seconds)

B&C

REPO (one quarter-second beep at quarter-second intervals)

B&E

Short circuit on the output

C&E

UPS shutdown by command from communication (USB or Liebert IntelliSlot®port)

(no audible alarm)

AC Input Indicator

LED flashing

L-N reverse

Battery Indicator

Flashing

Internal battery source not available (continuous audible alarm); check battery

connection, power down and reboot UPS

Bypass Indicator

Flashing

Utility power voltage or frequency is out of tolerance; bypass is unavailable

Single-Phase UPS & Server Cabinets Technical Support

[email protected]

800-222-5877

Outside North America: +00800 1155 4499

Emerson Network Power Worldwide Locations

United States

1050 Dearborn Drive

P.O. Box 29186

Columbus, OH 43229

800-222-5877

Europe

Via Leonardo Da Vinci 8

Zona Industriale Tognana

35028 Piove Di Sacco (PD) Italy

+39 049 9719 111

Fax: +39 049 5841 257

Asia

29/F, The Orient Square Building

F. Ortigas Jr. Road, Ortigas Center

Pasig City 1605

Philippines

+63 2 687 6615

Fax: +63 2 730 9572

DISCONTINUED

Inhaltsverzeichnis

Andere Emerson UPS Handbücher

Emerson

Emerson 10 kVA Bedienungsanleitung

Emerson

Emerson Liebert Nfinity 12-20kVA Bedienungsanleitung

Emerson

Emerson ECP-024 Bedienungsanleitung

Emerson

Emerson Liebert PowerSure PST Bedienungsanleitung

Emerson

Emerson GXT5000R-208 Bedienungsanleitung

Emerson

Emerson Liebert GXT4-5000RT208 Bedienungsanleitung

Emerson

Emerson Liebert PSA Bedienungsanleitung

Emerson

Emerson Liebert NX Bedienungsanleitung

Emerson

Emerson Liebert APM 15-90kVA Bedienungsanleitung

Emerson

Emerson Liebert Series 610 Bedienungsanleitung

Emerson

Emerson SolaHD SDU DC UPS B Series Bedienungsanleitung

Emerson

Emerson Liebert ITA Bedienungsanleitung

Emerson

Emerson Liebert GXT4-5000RT230 Bedienungsanleitung

Emerson

Emerson LIEBERT NX 40-120KVA Bedienungsanleitung

Emerson

Emerson Liebert APM 90 Bedienungsanleitung

Emerson

Emerson Liebert itON BX Bedienungsanleitung

Emerson

Emerson Liebert itON BX Bedienungsanleitung

Emerson

Emerson Liebert GXT3-5000RT230 Bedienungsanleitung

Emerson

Emerson Liebert NXL 250-400kVA Bedienungsanleitung

Emerson

Emerson Liebert PSP500MT3-230U Bedienungsanleitung

Emerson

Emerson 7400M Series Bedienungsanleitung

Emerson

Emerson Liebert NX 400V Bedienungsanleitung

Emerson

Emerson Liebert eXM Bedienungsanleitung

Emerson

Emerson Liebert GXT3-3000RT120 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung