EMG 91 Service-Handbuch

Warranty

All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If

upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This

warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.

PO BOX 4394

SANTA ROSA, CA

95402 USA

P (707) 525-9941

F (707) 575-7046

EMGPICKUPS.COM

0230-XXXXX

*Note: Magnet Type: A (Alnico) C (Ceramic)

2.750

1.500 (38.1)

(86.3)

.430 MAX (TYP .400)

(10.9)

.527 MAX (TYP .500)

(13.4)

INSTALLATION INFORMATION

EMG MODELS: EMG-91

ABOUT THE EMG-91:

Their are several benefits to using an active pickup for an arch top. Firstly, the pickup can be designed for great tone because output level

is not an issue. In addition, the EMG design insures the pickup is virtually noiseless and doesn’t need string grounding. It is almost impossible

to ground the strings of an arch-top guitar, so the pickup needs to be noiseless in its design.

Mounting:

The EMG-91 is designed as a low-profile pickup for arch-top guitars. Because all arch-top guitars are different, mounting the pickup

is usually unique in most cases. The pickup can be mounted on its bottom surface to a pickguard, or can be mounted with the EMG-91 bracket kit.

It’s best to look over this sheet, as well as the EMG-91 Bracket kit instructions, consider the following options and then proceed.

Power:

The EMG-91 needs to be powered by a 9 Volt battery. This can be accomplished by putting a battery holder in the instrument, or using an inline

external battery box with a stereo cable from the instrument to the battery box and a patch cable from the battery box to the amp.

Volume and Tone Controls:

Some instruments have volume and tone controls mounted to the pickguard, some don’t. Some controls are low-profile, some are not.

Both the Volume and Tone Control for the EMG-91 are 25K Ohm (audio taper).

SPECIFICATIONS: MODEL:

Logo Color Silver

Magnet Type * C

Resonant Frequency (KHz) 4.05

Output Voltage (String) 1.00

Output Voltage (Strum) 3.00

Output Noise (60 Hz) -101

Output Impedance (Kohm) 10

Current @9V (Microamps) 80

Battery Life (Hours) 3000

Maximum Supply (Volts DC) 27

Diagram #2

One Pickup

One Volume

One Tone

TIP

RING

SLEEVE

Diagram #4

FROM TONE

OR VOLUME

BATTERY

NEG (-)

RED to BATTERY BUSS

Soldering to the 152B Panel Jack:

If your instrument has a long Panel Jack like the one below

you will have to solder the output cable as shown.

Ground (Black) to the Sleeve

Signal (White) to the Tip

Battery Negative (Black) to the Ring

- 9V +

Diagram #5

Solder the RED wire from the Battery Holder and/or

pickups and re-insert the Header into the insulation cover

Soldering to the battery buss:

If your instrument has an older EMG Pickup you can solder the

pickup RED wire to the buss. Simply use some needle nose pliers,

pull out the V+ header and solder the RED Wire from the pickup(s)

to any of the pins and then re-insert the header into the housing.

Installation Instructions:

EMG Models: EMG-91

91 Instructions Page 2

Installation (One Pickup Guitars):

1) Plug the pickup cable onto the EMG Pickup header as shown

in diagram #1 and route the cable to the control cavity.

If the cable is too long, wind up the excess and keep it

under the pickup if possible.

Master Volume control only

2) Refer to diagram #2. Plug both the Pickup cable and the output

cable onto the Volume control as shown, then go to step 4.

Master Volume and Tone control

3) Refer to diagram #3. Plug the Pickup cable onto the Volume

control as shown. Plug a coax cable from the Volume control

to the Tone control. Plug the output cable onto the tone

control as shown.

4) Connect the wires of the output cable to the output jack by

pushing the connectors on as shown.

WHITE wire to the TIP (T) contact,

BLACK wire to the SLEEVE (S) contact

BLACK Battery Negative wire to the RING (R) contact.

5) Using the battery buss, insert the RED wire of the pickup,

and the battery RED wire. Extra pins can be used for

EMG Accessories.

6) Put the battery in the insulating foam piece provided

and place it securely in the control cavity.

We suggest that you plug in the instrument and

test it before closing the control cavity.

OUTPUT

PASSIVE

TONE

FROM PICKUP

BATTERY

NEG (-)

RED

BATTERY

BUSS

OUTPUT CABLE

MASTER

VOLUME

- 9V +

Diagram #1

Insert the plug onto the 3 pin header

of the pickup as shown above.

Note the orientation arrow.

1.500

(38.1)

1.000

(25.4)

.500

(12.7)

.250

(6.35)

2.062 (52.37)

.100

(2.54)

D .120

(3.05)

R .062

(1.57)

91 Instructions Page 3

Beliebte Zubehör für Musikinstrumente Handbücher anderer Marken

Behringer

Behringer AIRPLAY GUITAR AG10 Bedienungsanleitung

FEURICH

FEURICH BASIC Bedienungsanleitung

thomann

thomann Harley Benton JA Bedienungsanleitung

NeoTech

NeoTech PAD-IT TUBA HARNESS Bedienungsanleitung

Duncan

Duncan SH-8n Invader Kurzanleitung

Palmer

Palmer The Junction PDI-09 Bedienungsanleitung

GuitarPCB

GuitarPCB Fuzzy Bee v2 Handbuch

Yamaha

Yamaha Tough-Terrain T-335 Bedienungsanleitung

LEWISMIDI

LEWISMIDI CZ Patch Library Bedienungsanleitung

Free The Tone

Free The Tone LB-2 Bedienungsanleitung

Duncan

Duncan Apollo Jazz Bass - neck Handbuch

dbx

dbx dB10 Bedienungsanleitung

TLA

TLA Tuning-Set CTS-32-C Bedienungsanleitung

Solo Music Gear

Solo Music Gear JEK-1 Bedienungsanleitung

Duncan

Duncan HyperSwitch Bedienungsanleitung

CNC Design

CNC Design QUAD COIL WINDER MK2 Bedienungsanleitung

FuzzDog

FuzzDog 3PDT Bedienungsanleitung

Hipshot

Hipshot Universal Mounting Plate Bedienungsanleitung