Emos P5603R Bedienungsanleitung

2101106001_31-P5603R_00_01_PRINT 80 × 90 mm

P5603R

GB Thermostat

CZ Termostat

SK Termostat

PL Termostat

HU Termosztát

SI Termostat

RS|HR|BA|ME Termostat

DE Thermostat

UA Tермостат

RO|MD Termostat

LT Termostatas

LV Termostats

EE Termostaat

BG Tермостат

FR Thermostat

IT Termostato

ES Termostato

NL Thermostaat

Other countries Thermostat

www.emos.eu

GB | Thermostat

The P5603R thermostat is designed for controlling heating and air-con-

ditioning systems.

Important

• Before the rst use, make sure to carefully read the instruction

manual for the thermostat, as well as the manual for the boiler or

air-conditioning equipment.

• Turn o power supply before installing the thermostat!

• Installation should be carried out by a qualied person!

• Follow applicable standards during installation.

Technical specications:

Switched load: max. 230 V AC; 6 A for resistive load; 2 A for inductive

load

Temperature measurement: 0°C to 40°C with 1°C resolution; accuracy

±0.5°C

Temperature setting: 5°C to 30°C in 1°C increments

Temperature dierential setting: 0.4°C

Power supply: 2× 1.5 V type AA (LR6) batteries

Accessories: 2 screws, 2 wall plugs

Dimensions and weight: 40 × 93 × 86 mm; 135 g

Description of the Thermostat (See Fig. 1)

1 – screen

2 – temperature setting wheel

3 – battery compartment

4 – fastening of the rear cover by screws

Screen Description (See Fig. 2)

1 – low battery indication

2 – temperature

3 – °C/°F temperature unit

4 – heating or cooling operating mode

Procedure for Removing the Front of the Thermostat (See Fig. 1)

INSTALLATION

Attention:

Before changing the thermostat, disconnect the heating/air-conditioning

system from the mains power in your at. This will prevent potential injury

by electric current.

Read the thermostat manual carefully before using the device for the

rst time.

Turn o power supply before installing the thermostat!

Follow applicable standards during installation.

Placement of the Thermostat

The placement of the thermostat signicantly aects its functioning. Choose

a location where family members spend most of their time,

preferably on the inside wall where air circulates freely, with no direct

sunlight. Do not place the thermostat

in the vicinity of heat sources (such as TV sets, radiators, fridges), or close

to a door (due to frequent shocks or vibrations). If you do not follow these

recommendations, the thermostat will not maintain room temperature

correctly.

Installation of the Thermostat

The rear cover of the thermostat has 6 pre-made openings for mounting

onto a wall.

Remove the rear cover and use the enclosed screws and wall plugs to

mount the thermostat to a wall.

The connection terminals are protected by a plastic cover, see Fig. 3.

Connect the wires leading out of the junction box to the marked terminals

on the thermostat in accordance with the wiring diagram.

Wiring Diagram

Voltage connection diagram for connecting thermostat P5603R to a boiler

with an „NO“ contact:

Max 230 V 6(2) A 230 V~N

NO NCCOM

Heating device requiring

230 V power supply, e.g.

central heating pump. Thermostat

* When connecting a cooling device to the thermostat, connect the „L“

phase conductor to the „NC“ terminal.

Zero-voltage connection diagram for connecting thermostat P5603R to

a boiler with an „NO“ contact:

Max 230 V 6(2) A

COM

NO NCCOM

Heating device requiring

zero-voltage contact, e.g.

gas boiler. Thermostat

Putting the Device into Operation

1. Remove the back portion of the thermostat and insert 2× 1.5 V AA

batteries. Only use 1.5 V alkaline batteries; do not use rechargeable

1.2 V batteries.

2. Replace the back of the thermostat.

3. The thermostat now has an active screen and is operational.

If the thermostat is not working properly, please check the polarity of the

batteries and whether they are suciently charged, or reset the thermostat

by removing and reinserting the batteries.

If appears on the screen, replace the batteries in the thermostat.

Setting Temperature

To increase temperature, turn the wheel right.

To reduce temperature, turn the wheel left.

The set temperature will be shown on the screen for 5 seconds, then the

room temperature will be shown instead.

Choosing Operating Mode

Unscrew the rear cover of the thermostat.

There is a DIP switch on the back of the thermostat which is used to set

the following functions.

Available Functions in HEATING Mode

cooling mode o 1 ON heating mode on

CHRONO mode o 2 CHRONO mode on

6 cycles/h 3 3 cycles/h

°F unit of temperature 4 °C unit of temperature

CHRONO (TPI) Mode

CHRONO mode, also known as TPI (Time Proportional and Integral) is an

algorithm that has a simple memory capable of „learning“ how to reach

and maintain room temperature. It has a basic calculating capability: It

uses collected data and current temperatures and predicts how long heat

needs to be generated (the boiler must remain on). It is a type of intelligent

control, since heat delivery lasts until the desired value is reached, then

the boiler is turned o to improve energy eciency.

The mode runs in cycles, with their length measured as number of cycles

per hour. During normal use, it is dicult to notice the dierence in the way

the heating system runs. However, it is noticeable that the thermostat runs

for a shorter period of time when room temperature starts approaching the

set temperature. Once the set temperature is reached, the operating cycles

become shorter to maintain the temperature. TPI calculates the speed at

which the room loses heat and prevents the room from getting colder by

activating heating as needed.

Setting CHRONO (TPI) Cycles

In heating mode, the CHRONO function can be set to 3 or 6 cycles per hour.

3 cycles are recommended for controlling underoor heating or controlling

a heat pump.

6 cycles are recommended for controlling a gas boiler or a zone valve.

Temperature Dierential Setting

If you turn o the CHRONO function, the thermostat will activate/deactivate

based on the temperature dierential.

The temperature dierential (hysteresis) is the dierence in temperature

required for switching the system on and o.

The dierential value is 0.4°C.

If, for example, you set the temperature in heating mode to 20°C, the

thermostat activates heating as soon as room temperature drops to 19.6°C

and switches heating o when temperature reaches 20.4°C.

Available Functions in COOLING Mode

cooling mode on 1 ON heating mode o

delay o 2 delay on

4 minute delay 3 2 minute delay

°F unit of temperature 4 °C unit of temperature

Delay prevents the thermostat from switching because of short-term

temperature changes – protects the boiler from frequently activating and

deactivating.

Upkeep and Maintenance

The product is designed to serve reliably for many years if used properly.

Here are some tips for proper operation:

• Read the manual carefully before using the product.

• Do not expose the product to direct sunlight, extreme cold, humidity

and sudden changes in temperature. This would reduce measuring

accuracy.

• Do not place the product in locations prone to vibration and shocks –

may cause damage.

• Do not subject the product to excessive force, impacts, dust, high

temperatures or humidity – doing so may cause malfunction, shorten

battery life, damage batteries and deform plastic parts.

• Do not expose the product to rain or high humidity, dropping or

splashing water.

• Do not place any open ame sources on the product, e.g. a lit candle,

etc.

• Do not place the product to places with inadequate air ow.

• Do not insert any objects into the product‘s vents.

• Do not tamper with the internal electrical circuits of the product – doing

so may damage the product and will automatically void the warranty.

The product should only be repaired by a qualied professional.

• To clean the product, use a slightly moistened soft cloth. Do not use

solvents or cleaning agents – they could erode the plastic parts and

cause corrosion of the electric circuits.

• Do not immerse the product in water or other liquids.

• In the event of damage or defect of the product, do not perform any

repairs by yourself. Have it repaired in the shop where you bought it.

Inhaltsverzeichnis

Sprachen:

Andere Emos Thermostat Handbücher

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung