EMS HFG01 Bedienungsanleitung

Products User Manual Template – Issue 2

Document number Y0321/DOC/038 Rev. 2

Author: ...............................................................

D Cullen BEng (Hons), MSc, CEng, CMgr, MIET, MIEEE, MCMI

Test Instrumentation Manager

Checked: .....................................................................................

M S Anslow MEng, CEng, MIET MIEEE

Senior Engineer (Products)

Approved: ................................................................

D Cullen BEng (Hons), MSc, CEng, CMgr, MIET, MIEEE, MCMI

Test Instrumentation Manager

HFG01

Operation

Manual

HFG01 Operation Manual

York EMC Services Page 2 of 21 Doc. No. Y0321/DOC/038 Rev. 2

HFG01

Operation Manual

Document Number

Y0321/DOC/038

HANGE

ISTORY

HEET

Date Issue Pag/Para

Description

30/03/2017 1 - 1

Issue

11/11/17 2 Safety instructions updated

UNCONTROLLED ELECTRONIC COPY

Users should satisfy themselves that they are in possession of the most up to date

version of this manual by calling +44 (0) 330 4303456 or by emailing

[email protected]

HFG01 Operation Manual

York EMC Services Page 3 of 21 Doc. No. Y0321/DOC/038 Rev. 2

Limited Warranty

York EMC Services warrants each HFG01 to be free

from defects in material and workmanship for a period of

one year from the date of shipment to the purchaser.

This warranty extends to the original purchaser only. It

does not apply to any product or parts subject to misuse,

neglect, accident, unauthorised service or abnormal

conditions of operation.

In the event a product covered by this warranty fails,

York EMC Services, will, without charge, repair and

recalibrate the instrument if returned to their test

laboratory within one year of the original purchase –

provided that York EMC Services examination discloses,

to its satisfaction, that the product is defective. York EMC

Services may, at its option, replace the product in lieu of

repair. If the defect was caused by misuse, neglect,

accident, unauthorised service or abnormal conditions of

operation, repairs will be billed at a nominal cost. In such

cases, an estimate will be provided before work is

started, if requested by the purchaser.

For warranty service, contact York EMC Services.

Provide the serial number of the equipment and

complete details regarding the failure. You will then be

given shipping instructions. Return the instrument to the

factory. Repairs will be made and the equipment will be

returned to you. York EMC Services assumes no

responsibility for loss of, or damage to, products in

transit.

HFG01 Operation Manual

York EMC Services Page 4 of 21 Doc. No. Y0321/DOC/038 Rev. 2

DISCLAIMER

THE HFG01 HAS BEEN DESIGNED TO PRODUCE HARMONIC AND FLICKER

DISTURBANCES TO THE POWER SUPPLY TO WHICH THE TEST PORT HAS

BEEN CONNECTED, AND AS SUCH IT IS ONLY INTENDED TO BE

CONNECTED TO SUITABLE TEST EQUIPMENT. CONNECTION TO THE

PUBLIC MAINS DISTRIBUTION NETWORK IS NOT PERMITTED.

YORK EMC SERVICES LTD ASSUMES NO LIABILITY FOR ANY DAMAGE

THAT MAY RESULT FROM THE USE OF THIS EQUIPMENT OUTSIDE ITS

RECOMMENDED OPERATING CONDITIONS.

PRECAUTIONS

THE HFG01 MUST NOT BE OPERATED WITH THE TEST SUPPLY INPUT

PLUGGED DIRECTLY INTO A PUBLIC MAINS SUPPLY SYSTEM.

WHEN OPERATED, THE HFG01 WILL CAUSE HARMONIC AND FLICKER

EMISSIONS TO THE SUPPLY CONNECTED TO THE TEST SUPPLY INPUT.

HFG01 Operation Manual

York EMC Services Page 5 of 21 Doc. No. Y0321/DOC/038 Rev. 2

INTRODUCTION................................................................................................. 6

DESCRIPTION.................................................................................................... 7

DESCRIPTION OF SYMBOLS ........................................................................... 8

SPECIFICATION................................................................................................. 9

4.1

PERATING MODES

......................................................................................... 9

4.2

ARMONICS AND FLICKER MEASUREMENT SYSTEM TEST SUPPLY

......................... 9

4.3

PERATOR INDICATORS

.................................................................................. 9

4.4

OWER REQUIREMENTS

.................................................................................. 9

4.5

NCLOSURE

..................................................................................................10

4.6

OMPLIANCE

.................................................................................................10

4.7

NVIRONMENT

...............................................................................................10

OPERATION......................................................................................................11

5.1

ONTROLS AND INDICATORS

...........................................................................11

5.2

UPPLYING POWER TO THE

HFG01.................................................................12

5.3

PERATING MODES

........................................................................................12

5.4

NABLING THE TEST

.......................................................................................13

5.5

ERFORMING A TEST

......................................................................................13

5.6

ROUBLESHOOTING A TEST

.............................................................................14

OUTPUT PERFORMANCE................................................................................16

6.1

LICKER

OAD

PERATION

.............................................................................16

6.2

ARMONICS

OAD

PERATION

.......................................................................16

6.3

ALIBRATION

.................................................................................................17

SAFETY.............................................................................................................18

ELECTROMAGNETIC COMPATIBILITY ..........................................................19

8.1

ENERAL

......................................................................................................19

8.2

MISSIONS

....................................................................................................19

8.3

MMUNITY

......................................................................................................19

8.4

-A

PPLICABILITY

.......................................................................................19

MAINTENANCE AND CALIBRATION...............................................................20

9.1

ISPOSAL

.....................................................................................................20

HFG01 Operation Manual

York EMC Services Page 6 of 21 Doc. No. Y0321/DOC/038 Rev. 2

1 I

NTRODUCTION

The Harmonics & Flicker Generator 01 (HFG01) has been designed by York EMC

Services for the purpose of providing an easy and reliable way to externally check

the performance of measurement systems used for testing against the EN/IEC

61000-3-2 harmonics and interharmonics and EN/IEC 61000-3-3 flicker standards.

The HFG01 allows the user to periodically verify their test equipment and its

operation together, helping to ensure compliance with standards and laboratory

quality procedures.

The HFG01 provides a series of harmonic and flicker disturbances of a nominal

but stable level. The HFG01 may therefore be used to verify the stability of a

measurement system. Additionally, due to its own stability it may be used as a

transfer standard from a calibrated system, or be used as a repeatable source of

interference for diagnostic and/or development design work.

HFG01 Operation Manual

York EMC Services Page 7 of 21 Doc. No. Y0321/DOC/038 Rev. 2

2 D

ESCRIPTION

The HFG01 simulates equipment under test (EUT), generating known, repeatable

levels of harmonic and flicker disturbance in one of four modes of operation.

The flicker test modes generate a fixed level of mains disturbance at a rate of 1 Hz

and 8.33 Hz. These modes support verification of the test systems used for EUT

flicker disturbance measurements as described in the EN/IEC 61000-3-3 test

standards.

The harmonics test modes are designed to produce a variety of harmonic-rich

current waveforms. These current waveforms support verification of the test

systems used for mains-powered equipment load current testing as described in

the EN/IEC 61000-3-2 test standards.

The HFG01 can be used with test systems operating at 230 Vac (nominal) supply

voltages and 50 Hz supply frequency. Connection to the test system is by a captive

lead pre-fitted with a CEE 7/7 European style plug thatfits directly with power outlet

used by a wide range of harmonics and flicker equipment.

The HFG01 itself is powered by a wide-input range AC/DC power supply unit that

is powered separately from the Test Supply under test. This ensures that the

disturbance signals generated by theHFG01 are not affected by the need to derive

the HFG01’s own supply needs from the Test Supply under test.

For ease of access all connections, user controls, and indicators are located on

the front panel of the HFG01. The HFG01 is supplied with the external power unit

with mains cable, manufacturer’s test certificate, and a CDROM containing digital

copies of the manual, test certificate, and files of the tabulated certificate data.

HFG01 Operation Manual

York EMC Services Page 8 of 21 Doc. No. Y0321/DOC/038 Rev. 2

3 DESCRIPTION

SYMBOLS

Symbols displayed on the product are listed below:

Caution

Protective Earth Terminal

Alternating current

HFG01 power supply on

HFG01 power supply off

Direct current

DC connector polarity

ESD handling precaution

Separate collection for WEEE-

Waste Electrical and Electronic

Equipment

HFG01 Operation Manual

York EMC Services Page 9 of 21 Doc. No. Y0321/DOC/038 Rev. 2

4 S

PECIFICATION

4.1 Operating modes

(See Section 5. Output Performance for details of typical measurement results)

4.1.1 Current harmonics

Frequency range 5 Hz to 2.0 kHz (50 Hz Test Supply)

Stability < 5% of the test limit in EN 61000-3-2 standard

4.1.2 Flicker disturbance

Flicker rate 1 Hz (50 Hz Test Supply only)

8.3 Hz (50 Hz Test Supply only)

Stability < 5% of the reading

4.2 Harmonics and flicker measurement system test supply

4.2.1 Test Supply ratings

Voltage 200 Vac to 253 Vac (230 Vac nominal input)

Current 3 A (peak)

Frequency 50 Hz

Power rating 500 W max

Connector CEE 7/7 European style plug for connecting the HFG01

to the Test Supply under test.

Insulation rating 3000 Vrms

4.3 Operator indicators

(See Section 4. Operation for a full description of the control and indicator functions)

4.3.1

Operation indicators

Test enabled / running

System alarm

4.4 Power requirements

HFG01

Input connector 2.1 mm DC power jack (inner conductor +ve)

Voltage input 24 Vdc

Power consumption 24 W max

Power supply unit

Input connector IEC plug

HFG01 Operation Manual

York EMC Services Page 10 of 21 Doc. No. Y0321/DOC/038 Rev. 2

Voltage input 100 Vac to 240 Vac (nominal)

Power consumption 50 W max

4.5 Enclosure

Overall dimensions (not including captive leads):

Length 330 mm

Width 320 mm

Height 170 mm

Weight 8 kg

4.6 Compliance

Safety Low Voltage Directive, 2014/35/EU

EMC EMC Directive, 2014/30/EU

4.7 Environment

4.7.1 Operating Temperature Range

Recommended Ambient 10ºC to 30ºC

Maximum Ambient 5ºC to 40ºC

4.7.2 Humidity

Relative humidity: 20% to 80% (non-condensing)

4.7.3 Protection

IP rating IP10

NOTE. Do not allow any obstructions to interfere with the operation of the fans, or

site the HFG01 such that airflow is restricted. Doing so will cause the equipment to

run at an increased temperature and in so doing may affect its operation.

Inhaltsverzeichnis

Andere EMS Tragbarer Generator Handbücher

EMS

EMS Piezon C51 Bedienungsanleitung

Beliebte Tragbarer Generator Handbücher anderer Marken

Kohler

Kohler 20EORZ Bedienungsanleitung

Powerhorse

Powerhorse 83171 Bedienungsanleitung

HURST

HURST ML-630-SI Bedienungsanleitung

ETQ

ETQ TG4000 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton 40265 Einrichtungshandbuch

ConMed

ConMed 7550 Bedienungsanleitung

Owon

Owon Waveform Generator Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

Power Stroke

Power Stroke PS906025 Bedienungsanleitung

Firefly

Firefly Cygnus CYG2400/460/24 Bedienungsanleitung

Draper

Draper PG950S Firmware-Update

PowerBoss

PowerBoss PowerBoss Bedienungsanleitung

SDMO

SDMO SH 4000 Bedienungsanleitung

EINHELL

EINHELL STE 5500 Bedienungsanleitung

Wanco

Wanco WI3000P Bedienungsanleitung

Full Boar

Full Boar FBT-3300 Bedienungsanleitung

Dwyer Instruments

Dwyer Instruments ASG Bedienungsanleitung

Westinghouse

Westinghouse WH1000i Series Bedienungsanleitung