Encore Networks BANDIT III Bedienungsanleitung

encor etworks

•

For information on trademarks, safety, limitations

of liability, and similar topics, see Notices.

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

BANDIT III Hardware Description

of 3 QuickStart Guides for the BANDIT III

his chapter provides information on the hardware for the BANDIT III™. The BANDIT III

is a high-end model in the BANDIT™ products, optimized for utility applications and

protocols.

The BANDIT III complies with the European Union's directive on restriction of hazardous

substances (ROHS). This directive places strict controls on pollutants, including the elimination

of lead in the manufacturing process.

The BANDIT III is available in a commercial chassis, with a standard hard plastic cover, or an

environmentally hardened chassis, with a metal cover. Hardened construction allows the

BANDIT III to operate over wide temperature ranges at remote sites that do not use

environmental control.

The BANDIT III, like all products in the BANDIT family, uses the ELIOS™ operating system.

In addition to its support of virtual private networks (VPNs) and its support of legacy protocols,

the BANDIT III can handle all variants of the Supervisory Control and Data Acquisition (SCADA)

protocol, both bit- and byte-oriented, with strong encryption of all traffic and complete remote

management capabilities after a simple plug-and-play installation.

Figure 1-1 shows the outer shell of a BANDIT III chassis. (Also see Section A.3.1, Physical

Specifications.)

Figure 1-1. BANDIT III Chassis

See the following sections:

•The BANDIT III Chassis

•Status LEDs

Home Module: BANDIT III Reference

Document 1

Version A.3, July 2014

Page 2

BANDIT III Reference Module, Document 1

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

1.1 The BANDIT III Chassis

The BANDIT III is a full-featured tabletop model in the BANDIT family, providing both

IPsec/SLE VPNs and legacy-protocol support. The BANDIT III offers enhanced

performance features, a full choice of connections for the expansion port, and support of up

to 30 simultaneous VPN tunnels. Like other BANDIT VPN devices, the BANDIT III’s VPNs

support DES and 3DES; in addition, the BANDIT II, the BANDIT III, and the VSR-1200 can

also support AES.

Note: For chassis and port specifications, see BANDIT III Hardware Specifications.

The BANDIT III is available in a basic chassis, a chassis with an Ethernet Switch Module. or

an E&M Signaling chassis, each with one DB25 serial port. The BANDIT III is also available

in an expanded chassis with four additional DB25 serial ports. See the following:

•Standard BANDIT III Chassis

•BANDIT III Chassis with Ethernet Switch Module

•Expanded BANDIT III Chassis with Internal Data Unit

•BANDIT III E&M Signaling Chassis

1.1.1 Standard BANDIT III Chassis

The basic BANDIT III chassis (Figure 1-2) contains LED indicators for the following items:

•Power

•Alarmstate

• Network Activity for the port on a card in the expansion port

• Network Activity for port 2 of a two-port card in the expansion slot1

• Carrier detect (CD) and activity (ACT) on the DB25 serial port

• 10base-T/100base-T (10/100), CD/ACT, and half-duplex/full-duplex (HD/FD) on the

WAN port

• 10/100, CD/ACT, and HD/FD on three LAN ports

• CD/ACT on the internal (cellular) wireless card’s internal port

• CD/ACT on the modem

The BANDIT III can hold one or two wireless cards for CDMA, EVDO CDMA, GPRS GSM,

or EDGE GSM wireless networks. One card is internal; the other can be installed in the

external expansion slot. Each wireless card for the BANDIT III includes an antenna. (A

plastic chassis can use an internal antenna or an external antenna but not both; a metal

chassis uses only an external antenna.)

1. The Network Activity 2 LED applies only to the dual T1/E1 CSU/DSU port.

BANDIT III Hardware Description

Page 3

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

Figure 1-2. BANDIT III Chassis, Front Panel, Basic Model

The BANDIT III is also available in an expanded model, with four additional DB25 RS232

serial ports. The expanded model includes all features of the basic BANDIT III, plus an

Internal Data Unit (IDU) consisting of four DB25 serial ports. The IDU provides additional

support for legacy functionality without the need for a peripheral device.

Figure 1-3 shows the expanded model, with individual Link LEDs near the top of the

faceplate for the four DB25 serial ports of the IDU and with one set of Link and Activity LEDs

for the IDU as a whole.

Figure 1-3. BANDIT III Chassis, Front Panel, Expanded Model

The basic BANDIT III chassis is available for 110/220 volts AC input power (Figure 1-4), for

-24/-48 volts DC input power (Figure 1-5), or for -12/-24 volts DC input power (Figure 1-6).

When you order a BANDIT III, you specify the type of input power it will use.

Note: Each DC-powered BANDIT III chassis also has a port for AC input power; you can

choose to connect or not to connect an AC power supply to the AC port. If you connect

both the DC port and the AC port to input power sources, the chassis will use the power

source that you connect first as the primary power source. The other power connection

will be on standby; it will provide power only if the primary power source fails.

If the primary power source fails, the standby power source immediately provides

power to the chassis and becomes the new primary power source. When the original

primary power source is restored, it becomes the new standby power source.

Consult your network administrator to determine whether your BANDIT III DC-

powered chassis will use only a DC input power configuration or will use a failover DC

and AC input power configuration.

Page 4

BANDIT III Reference Module, Document 1

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

Figure 1-4. BANDIT III Chassis, Rear Panel, Basic Model,

110/220 VAC Input Power

Figure 1-5. BANDIT III Chassis, Rear Panel, Basic Model,

-24/-48 VDC Input Power

(or Failover -24/-48 VDC and 110/220 VAC Input Power)

Figure 1-6. BANDIT III Chassis, Rear Panel, Basic Model,

-12/-24 VDC Input Power

(or Failover -12/-24 VDC and 110/220 VAC Input Power)

The following items are on the back of the basic BANDIT III chassis (Figure 1-4, Figure 1-5,

or Figure 1-6):

• Two ports (labeled “Cellular”) for antennas for wireless cards, for connection to wireless

networks

• Two earth ground connection screws

• A DB9 supervisory port for management

• A connector for AC input power

BANDIT III Hardware Description

Page 5

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

• If you ordered a chassis for DC power: A connector for DC input power (in addition to a

connector for AC input power)

• A V.90/V.92 modem port

• Four RJ45 10/100-Base-T Ethernet ports:

- One WAN port, typically used as the network uplink to the host

- Three LAN ports, typically connected to local IP devices

Note: The three Ethernet LAN ports on the BANDIT III constitute a LAN switch; you can

use them to create a small network.

• An expansion slot for a card that provides an additional port. The expansion slot accepts

one of several expansion cards for specific interfaces:

- Ethernet port, for a DMZ LAN

- DB25 serial port, configurable as RS-232, RS-449, V.35, or X.21

- 56k CSU/DSU port

-T1/E1CSU/DSUport

- Dual-port T1/E1 CSU/DSU port, with drop-and-insert capability

- A second wireless card; this can be the same type (CDMA, EVDO CDMA, GPRS GSM,

or EDGE GSM) as the internal wireless card or a different type from the internal

wireless card.

Note: For more information about ports for the expansion slot, see Ports in the BANDIT

Products.

•Analarmport

• A DB25 serial port

1.1.2 BANDIT III Chassis with Ethernet Switch Module

The BANDIT III is also available with an Ethernet Switch Module (ESM) comprising six LAN

ports. This BANDIT III chassis is available for -12/-24 volts direct DC input power

(Figure 1-7) or for 5 volts DC input power via the AC power adapter. The DC chassis can use

a failover DC and AC input power configuration.

Figure 1-7. BANDIT III Chassis, Rear Panel, Basic Model,

with Ethernet Switch Module, -12/-24 VDC Input Power

(or Failover -12/-24 VDC and 110/220 VAC Input Power)

Page 6

BANDIT III Reference Module, Document 1

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

The BANDIT III chassis with an ESM provides all features of the standard BANDIT III

chassis, plus 6 additional LAN ports (the ESM).

The ESM ports are configured by selecting the LAN port in the menus for port configuration.

(See the Port Configuration Module.) The ESM functions as a unit, in conjunction with the

LAN DMZ switch.

1.1.3 Expanded BANDIT III Chassis with Internal Data Unit

As stated earlier, the BANDIT III is also available in an expanded model, with an Internal

Data Unit (IDU) comprising four DB25 serial ports, for additional VPN functionality. The

expanded BANDIT III chassis is available for 110/220 AC volts input power (Figure 1-8), for

-24/-48 volts DC input power (Figure 1-9), or for -12/-24 volts DC input power (Figure 1-10).

As stated earlier, each DC chassis can use a failover DC and AC input power configuration.

Figure 1-8. BANDIT III Chassis, Rear Panel, Expanded Model,

110/220 VAC Input Power

Figure 1-9. BANDIT III Chassis, Rear Panel, Expanded Model,

-24/-48 VDC Input Power

(or Failover -24/-48 VDC and 110/220 VAC Input Power)

BANDIT III Hardware Description

Page 7

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

Figure 1-10. BANDIT III Chassis, Rear Panel, Expanded Model,

-12/-24VDC Input Power

(or Failover -12/-24 VDC and 110/220 VAC Input Power)

In summary, there are two chassis models:

•Basic(Figure 1-2) or expanded (Figure 1-3). For each chassis model, there are:

- Three standard input-power port configurations (110/220 VAC, -24/-48 VDC, or

-12/-24 VDC). The three configurations for the basic model are shown in Figure 1-4,

Figure 1-5, and Figure 1-6. The three configurations for the expanded model (with four

IDU serial ports) are shown in Figure 1-8, Figure 1-9, and Figure 1-10. These total six

physical port configurations for the BANDIT III chassis.

- Two failover input-power configurations (-24/-48 VDC with 110/220 VAC or

-12/-24 VDC with 110/220 VAC). Each BANDIT III chassis that uses DC input

power—basic (Figure 1-4 and Figure 1-5) and expanded (Figure 1-9 and

Figure 1-10)—can instead use a failover DC and AC power option. This failover power

capability adds four power configuration options for the BANDIT III chassis.

• The six port configurations and the four additional power configurations total ten

standard port and power configurations for the BANDIT III chassis.

1.1.4 BANDIT III E&M Signaling Chassis

For information on this chassis and its functions, see The BANDIT III E&M Signaling Chassis.

1.1.5 BANDIT III Port and Power Configurations

Table 1-1 lists the BANDIT III’s standard port and power configurations.

Note: Also see The BANDIT III E&M Signaling Chassis.

Page 8

BANDIT III Reference Module, Document 1

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

Note: For chassis and port specifications, see BANDIT III Hardware Specifications.

Warning: Always follow safety procedures when working with electrical equipment.

See Basic Safety Guidelines.

1.1.6 Throughput

The BANDIT III chassis has the following system throughput:

• LAN to WAN, without encryption: 9,000 packets/second, with incoming and outgoing

traffic at 64 bytes/packet

• LAN to WAN, with encryption and decryption: 1,800 packets/second, with incoming

traffic at 50 bytes/packet and outgoing traffic at 100 bytes/packet

1.1.7 Power Supply

The BANDIT III is available in models that accept power from a DC power source (at

-24/-48 VDC or -12/-24 VDC) or in models that accept power from an industry-standard

autosensing 100/240 VAC adapter connected to an AC power source. A BANDIT III DC-

powered chassis will also accept input from an AC power supply. The BANDIT III’s AC

power supply converts the AC input power to 5 VDC at 3 amps output for use by the

BANDIT III chassis.

Table 1-1. BANDIT III Chassis Standard Port and Power Configurations

Chassis

Model

IDU Serial

Ports

Input Power

Configuration

Input Power Details

110/220 V

-24/-48 V

-12/-24 V

Basic

and

ESM

AC •

DC •

•

Failover DC

and ACa

••

Expanded

•AC •

•DC •

••

•Failover DC

and ACb

••

•••

a. This is a basic DC chassis (-24/-48 VDC or -12/-24 VDC), with standby AC power.

b. This is an expanded DC chassis (-24/-48 VDC or -12/-24 VDC), with standby AC power.

BANDIT III Hardware Description

Page 9

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

1.1.8 Supervisory Port

A Supervisory cable connects the BANDIT III’s DB9 Supervisory port to the DB9 serial port

of a computer with a control console (such as a PC).

Note: If the Supervisory connection is through a Universal Serial Bus (USB) port on the

control console computer (such as a personal computer, PC), use an appropriate adapter—

for example, a DB9-to-USB adapter.

If you wish, you can give the BANDIT III an IP address; then you can configure and monitor

the BANDIT III over the LAN. This frees the DB9 Supervisory port for use as an additional

serial port for legacy applications.

For specifications of the DB9 serial port, see Section A.1.1, DB9 Supervisory Port, in BANDIT

III Hardware Specifications.

1.1.9 Standard Network Ports

The following sections discuss the BANDIT products’ port connections to network devices.

•Section 1.1.9.1, Ethernet Ports

•Section 1.1.9.2, Modem Port

•Section 1.1.9.3, Serial Port

•Section 1.1.9.4, Wireless Ports

Also see Section 1.1.10, Expansion Ports.

Note: The BANDIT’s data ports can be configured in the software. The data rates for

synchronous and asynchronous data ports are shown in Table A-10 and Table A-11.

1.1.9.1 Ethernet Ports

The BANDIT III has one WAN Ethernet port and three LAN Ethernet ports. The external

expansion slot can hold an additional Ethernet port. Each 10/100-Base-T Ethernet connection

is implemented over unshielded twisted-pair (UTP) wire, using a standard RJ45 connector.

Figure A-3 shows the RJ45 connector pins. Table A-3 lists the RJ45 pin configuration.

See the following sections:

•Section 1.1.9.1.1, The WAN Ethernet Port

•Section 1.1.9.1.2, The LAN Ethernet Port

•Section 1.2.1, Ethernet DMZ Port for the Expansion Slot

1.1.9.1.1 The WAN Ethernet Port

Table 1-2 lists the WAN port’s interface options.

Table 1-2. WAN Port Interface Options

Standard

• BANDIT III: 10/100-Base-T, with an RJ45 connector

Page 10

BANDIT III Reference Module, Document 1

Go to

Table of

Contents

o to

Top

Doc

Go to

List of

All Docs

1.1.9.1.2 The LAN Ethernet Port

Table 1-3 shows the interface options for the LAN port.

The LAN Port has the following IP features:

• Static routing

• Standard RIP V1, V2 routing

• Prioritization on Layers 2 and 3

• DiffServ marking and classification for end-to-end prioritization

• IP Quality of Service

• Dynamic bandwidth allocation

• 802.1q VLAN tagging

• VRRP (RFC 3768)

• Fragmentation and reassembly (MTU) LAN

• DHCP server, client, relay; Bootp

• SNMP, MIB II

•ARP;ProxyARP

• Routing over VPN tunnels

1.1.9.2 Modem Port

An internal modem resides in the BANDIT III. Connect the modem port to an RJ11 telephone

jack.

1.1.9.3 Serial Port

The BANDIT III uses a DB25 serial port.

Table 1-4 lists the BANDIT III’s DB25 serial port interface options. Table 1-5 lists the BANDIT

III’s DB25 serial port protocol options. For the BANDIT III’s DB25 serial port pin

configuration, see Table A-5. Use the BANDIT III software to set the DB25 serial port as DCE

or DTE.

Table 1-3. LAN Port Interface Options

Standard

• BANDIT III: 10/100-Base-T, with an RJ45 connector

Table 1-4. BANDIT III DB25 Serial Port Interface Options

Standard

• Serial:

- RS-232 (256 kbps sync, 230 kbps async)

Inhaltsverzeichnis

Andere Encore Networks Netzwerk-Hardware Handbücher

Encore Networks

Encore Networks EN-1000 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung