Encore Classic 26SP100 Programmierhandbuch

MANUAL

OPERATORS/PARTS

26SP100

OPERATORS MANUAL

SECTION



SIGNAL WORDS

This symbol means “Attention! Become

Alert! Your Safety is Involved!” The symbol

is used with the following signal action words

to attract your attention to safety messages.

The message that follows the symbol con-

tains important information about safety.

Signal Word:

 WARNING:

The signal action word “ WARNING” denotes

that a hazard exists on or near the machine

that can result in injury or death if proper

precautions are not taken.

 CAUTION:

The signal action word “CAUTION” is a

reminder of safety practices on or near the

machine that could result in personal injury if

proper precautions are not taken.

NOTES:

The signal action word “NOTES” denotes

relevant information to assist you in the

performance of a task.

GENERAL

This manual contains techincal data on the

following Encore commercial mowers.

26SP100

INTRODUCTION

Your mower was built to the highest

standards in the industry. However, the

prolonged life and maximum efficiency of

your mower depends on you following the

operating, maintenance and adjustment

instructions in this manual.

We encourage you to contact your local

Encore dealer for repairs. All Encore dealers

are informed of the latest methods to service

this equipment and provide propmt and

efficient service. They carry a full line of

Encore service parts. This manual includes a

parts section to help in correctly ordering

parts when necessary.

A replacement Operator’s Manual is available

from your Encore Dealer or by contacting

Encore Manufacturing Co., Inc., Service

Department at PO Box 888, Beatrice, NE

68310. Please indicate the complete model

and serial number of your Encore product.

The “Right” and “Left”,”Front” and “Rear” of

the machine are referenced from the

operator’s perspective when in the normal

operating position and facing forward travel

direction.

GENERAL SAFETY INSTRUCTIONS

READ THIS OPERATOR’S MANUAL and

instructions furnished with attachments.

Perform only those maintenance procedures

described in this manual. If major repairs are

ever needed or assistance is desired, contact

an Authorized Encore Dealer. To ensure

optimum performance and safety, always

purchase genuine Encore replacement parts

and accessories.

GENERAL RULES OF SAFETY FOR

OPERATION.

The follow general rules of safety should be

followed whenever THE MOWER IS

BEENING USED. Good judgement and

common sense should always prevail.

1. Read and thoroughly understand this

manual, and all decals on unit, before

attempting to operate.

 WARNING:

DO NOT allow children to operate the

machine. DO NOT allowanyadulttooperate

the machine without proper instruction.

2. DO NOT mow when children and/or

bystanders are present.

3. ALWAYS WEAR SUITABLE

CLOTHING when operating machine, proper

boots, gloves, and eye protection- NO

LOOSE-FITTING APPERL that could get

caught in the moving parts of machine.

4. Always be alert when operating

machine. Do not let outside interests distract

you.

5. Always clear area to be mowed of any

foreign objects (stones, wire, cans, bottles,

etc. That could be picked up and thrown by

mower.

6. Always be certain that any self-

propelling unit is DISENGAGED before

attempting to start engine.

7. Always disengage power, stop engine,

and remove spark plug wire, before

attempting any inspection, adjustment,

cleaning, or repair.

8. Use care when mowing around fixed

objects. Never deliberately run over foreign

objects as damage to machine and/or others

may result.

9. Never mow on a surface angle greater

than 15 degrees. Mow across a slope less

than 15 degrees, NEVER up and down.

10. Do NOT alter governor setting on

engine. Engine over speed could result in

severe damage and/or injury.

11. Keep all shields and safety devices

intact. DO NOT try to circumvent or disable

these features.

12. DO NOT mow at night or in times of

low visibility.

13. DO NOT operate engine in confined

air space where carbon monoxide fumes can

collect.

14. ALWAYS STOP ENGINE before

leaving mower unattended for any length of

time.

15. DO NOT operate machine without

muffler.

16. KEEP all nuts, bolts and screws tight.

Keep your High Wheel in good working

condition.

 CAUTION:

Neveradd fueltoa runningengine.ALWAYS

WAIT at least five minutes before refueling

and REFUEL WITH THE ENGINE OFF.

KEEP FUEL AWAY FROM SPARKS OR

FLAMES. WIPE AWAY any fuel spillage

BEFORE starting unit.

SET-UP AND MAINTIANENCE

 CAUTION:

Engine has not been serviced prior to delivery. Consult engine manual to

properly service engine before use.

1. Install handle by flipping handle into place using the bolts located in the

handle support. See diagram a. (Note that the handle frame is slotted so the

handle can be adjusted to the right operator height for operator comfort).

2. Install wheel drive engaging rod and adjust so that the drive cogs engage

the tire. See diagram (b & c). Note that the tires should be inflated to 30

pounds.

Diagram C

Diagram A

Diagram B

3. Drive chain may be adjusted by loosing the top bracket located by the cog

assemble (Refer to figure d) When adjusting the drive chain you must adjust

both sides equally. After adjusting the chain reset cog tension by removing the

pin in the yoke attached to the cog bracket and shortening the rod length to

increase cog pressure.

4. The drive belt maybe adjusted by loosening the bolts in the lower frame

support and shifting it forward of back. (Refer to f)

Figure D

Figure E

1 1/2"

3 1/4"

HEIGHTS ADJUSTMENTS:

Adjust cut setting by changing wheel heights according to figure (c).

Mower blade:

Check sharpness of mower blades after every 10 hours of operation. To sharpen

blades proceed as follows.

a. Block front of mower up.

Figure C

 CAUTION:

Stop engine and remove spark plug for safety.

b. Remove blade by turning bolt counter clockwise.

c. Blades should be discarded when worn excessively. See Sketch.

d. Sharpen blades with a hand file, electric grinder or blade sharpener. Wear

gloves and eye protection when sharpening. Grind blade at original bevel.

e. Check balance of blade by positioning the blade on a nail or blade balance

pedestal.

f. Reinstall blade making sure that the disc spring washer is bowl side up and re-

torque bolt to 90 ft pounds.

New Blade

25 Degrees When Notch Starts

Discard Blade

Dangerous!

Drive Lever

Throttle Control

Brake Bail Drive Bail

To Begin Operation

The throttle control/choke lever is located on left side of handlebar. To engage

choke, push throttle control lever all the way forward.

Choke as required and start engine.

With engine running, engage the brake bail by squeezing it to the handlebar.

Then push forward on the black plastic drive lever (located on left side of

handlebar just above the throttle control) until it locks into the forward position.

To drive machine forward, engage the

wheel drive bail (located on the

uppermost part of handlebar) by

squeezing it to the handlebar.

To stop machine from pulling forward,

release only the wheel drive bail.

To shut off engine: release the wheel

drive bail and the brake bail. Adjust the

throttle control to the engine stop

position.

1. 12 V electric starter

2. Oil drain plug

3. F uel fill

4. Fuel tank

5. Oil fill/Dips tick

6. Finger guard

7. R ope handle

8. Air cleaner

9. E ngine Model Type Code

xxxxx xxxx xx xxxxxxxx

10. Muffler/(Muffler guard, if equipped)/

(S park arres ter, if equipped)

11. S park plug wire

12 . R ota ting s c ree n

13. Blower housing

14. Fuel filter

15. Carburetor

712

GENERAL INFORMATION

ENGINE MODEL

T his is a single cylinder, L-head, air-cooled engine. It is a

low emissions engine.

MODE L S E R IE S 280000

Bore 3-7/16 in. (87.31 mm). . . . . . . . . . . . . . . . . . . . . . . . . .

S troke 3-1/16 in. (77.78 mm). . . . . . . . . . . . . . . . . . . . . . . .

Displacement 28.42 cu. in. (465.7 cc). . . . . . . . . . . . . . . .

Note: F or practical operation, the hors epower loading should

not exceed 85% of rated horsepower. E ngine power will de-

crease 3-1/2% for each 1,000 feet (300 meters) above sea

level and 1% for each 10 F (5.6 C) above 77 F (25 C).

Engine will operate satisfactorily at an angle up to 15 .

TUNE -UP S PE CIFICATIONS

Armature air gap 0.010 – 0.014 in. (0.25 – 0.36 mm). . .

S park plug gap 0.030 in. (0.76 mm). . . . . . . . . . . . . . . . . .

Va lve clea rance with valve s prings ins ta lled and pis ton 1/4 in.

(6 mm) past top dead center (check when engine is cold).

S ee R epair Manual P/N 270962.

Model 280000 intake .005 – .007 in. (.13 – .18 mm). . . . .

Model 280000 exhaust .009 – .011 in. (.23 – .28 mm). . .

C A UT ION: T his engine is shipped from B riggs &

S tratton without oil. C heck oil level before s tarting

e ngine. If you s ta rt the e ngine without oil, the e ngine

will be damaged beyond repair and will not be

covered under warranty.

OIL CAPACITY

E ngine Model S eries 280000 holds about 1-1/2

qts (48 ozs or 1.4 ltrs).

TYPE OF OIL TO USE

Us e a high quality detergent oil clas s ified “F or S ervice

SF, SG, SH, SJ” or higher, such as Briggs & Stratton

30W, Part Number 100005 (20 oz) or 100028 (48 oz).

Do not us e s pecial additives.

Choose a viscosity according to the table opposite.

Note: S ynthetic oil meeting ILS AC GF-2, API

certification mark and AP I service s ymbol

(shown at left) with “S J/CF E NE R GY CON-

S E R V ING ” or higher, is an acceptable oil at all

temperatures. Use of synthetic oil does not

alter required oil change intervals.

F-20 0 20 40 60 80 100

C-30 -20 -10 0 10 20 30 40

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

* C AUT ION: Air cooled engines run hotter than

automotive engines. The use of non-synthetic

multi-vis cos ity oils (5W-30, 10W-30, etc.) in

temperatures above 40 F (4 C ) will result in higher

than normal oil cons umption. W hen us ing a

multi-vis cos ity oil, check oil level more frequently.

** CAUTION: S AE 30 oil, if used below 40 F (4 C), will

res ult in hard s tarting and pos s ible engine bore

damage due to inadequate lubrication.

SAE Viscosity Grades

PARTS MANUAL

SECTION

Inhaltsverzeichnis

Andere Encore Rasenmäher Handbücher

Encore

Encore RAGE ER48FX730VX Bedienungsanleitung

Encore

Encore EDGE EE48FR691V32SS Bedienungsanleitung

Encore

Encore 32B100 Bedienungsanleitung

Encore

Encore Rage ER52FX730V Bedienungsanleitung

Encore

Encore 34K350Z Bedienungsanleitung

Encore

Encore EW32FS481V Bedienungsanleitung

Encore

Encore Hydro Series Handbuch

Encore

Encore Premier HydroPro 48K250WT Bedienungsanleitung

Encore

Encore RAGE ER48FX730VL Bedienungsanleitung

Encore

Encore Prowler EP60MX800EV5 Bedienungsanleitung

Encore

Encore Rage ER32FS600VL Bedienungsanleitung

Encore

Encore EE48FR691V32 Bedienungsanleitung

Encore

Encore Caliber EC52FX730V3 Bedienungsanleitung

Encore

Encore EDGE EE48FR691V32CE Bedienungsanleitung

Encore

Encore CALIBER EC52FX801V4 Bedienungsanleitung

Encore

Encore EE48LS2P82F32 Bedienungsanleitung

Encore

Encore EW36FS481VH Bedienungsanleitung

Encore

Encore Caliber EC52FX730V3CA Bedienungsanleitung

Encore

Encore EW28X11BX Bedienungsanleitung

Encore

Encore DART ED34FS600V Bedienungsanleitung

Encore

Encore 61K650P Bedienungsanleitung

Encore

Encore X-TREME 60K25X Bedienungsanleitung

Encore

Encore Fuzion F48B24 Bedienungsanleitung

Encore

Encore EDGE EE52FX691V34CA Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung