Endress+Hauser ITEMP TMT82 Technische Daten

Products Solutions Services

Brief Operating Instructions

iTEMP TMT82

2-channel temperature transmitter

These instructions are Brief Operating Instructions; they do

not replace the Operating Instructions included in the scope of

supply.

Detailed information can be found in the Operating

Instructions and the additional documentation.

Available for all device versions via:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

KA01095T/09/EN/18.19

71463446

2019-12-17

iTEMP TMT82

2 Endress+Hauser

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

iTEMP TMT82 Table of contents

Endress+Hauser 3

Table of contents

1 Important document information ................................................. 3

1.1 Function of document and how to use ....................................................... 3

1.2 Symbols ............................................................................. 4

1.3 Tool symbols ..........................................................................5

1.4 Registered trademarks .................................................................. 5

2 Basic safety instructions .......................................................... 5

2.1 Requirements for the personnel ............................................................ 5

2.2 Designated use ........................................................................ 6

2.3 Operational safety ......................................................................6

3 Incoming acceptance and product identification ................................... 6

3.1 Incoming acceptance .................................................................... 6

3.2 Product identification ................................................................... 7

3.3 Scope of delivery ....................................................................... 9

3.4 Certificates and approvals ................................................................ 9

3.5 Transport and storage ................................................................... 9

4 Mounting ....................................................................... 10

4.1 Mounting requirements ................................................................ 10

4.2 Mounting ........................................................................... 11

4.3 Post-mounting check .................................................................. 15

5 Electrical connection ............................................................ 16

5.1 Connection conditions .................................................................. 16

5.2 Quick wiring guide .................................................................... 16

5.3 Connecting the sensor cables ............................................................. 17

5.4 Connecting the transmitter .............................................................. 19

5.5 Special connection instructions ........................................................... 20

5.6 Post-connection check ..................................................................21

6 Operating options ............................................................... 22

6.1 Measured value display and operating elements ............................................... 22

6.2 Configuration of transmitter and HART® protocol .............................................. 25

7 Commissioning .................................................................. 25

7.1 Post-installation check ................................................................. 25

7.2 Switching on the transmitter ............................................................. 25

7.3 Enabling configuration ................................................................. 26

1 Important document information

1.1 Function of document and how to use

1.1.1 Document function

These instructions contain all the essential information from incoming acceptance to initial

commissioning.

Important document information iTEMP TMT82

4 Endress+Hauser

1.1.2 Safety Instructions (XA)

When using in hazardous areas, compliance with national regulations is mandatory. Separate

Ex-specific documentation is provided for measuring systems that are used in hazardous

areas. This documentation is an integral part of these Operating Instructions. The installation

specifications, connection data and safety instructions it contains must be strictly observed!

Make sure that you use the right Ex-specific documentation for the right device with approval

for use in hazardous areas! The number of the specific Ex documentation (XA...) is provided

on the nameplate. If the two numbers (on the Ex documentation and the nameplate) are

identical, then you may use this Ex-specific documentation.

1.1.3 Functional safety

Please refer to Safety Manual SD01172T/09 for the use of approved devices in protective

systems according to IEC 61508.

1.2 Symbols

1.2.1 Safety symbols

Symbol Meaning

DANGER

A0011189-EN

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will

result in serious or fatal injury.

CAUTION

A0011191-EN

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can

result in minor or medium injury.

NOTICE

A0011192-EN

NOTE!

This symbol contains information on procedures and other facts which do not result

in personal injury.

1.2.2 Symbols and notation for certain types of information

Symbol Meaning

A0011193

Tip

Indicates additional information.

A0011194

Reference to documentation

Refers to the corresponding device documentation.

A0011195

Reference to page

Refers to the corresponding page number.

A0011196

Reference to graphic

Refers to the corresponding graphic number and page number.

1., 2., 3. Series of steps

iTEMP TMT82 Basic safety instructions

Endress+Hauser 5

1.3 Tool symbols

Symbol Meaning

A0011220

Flat blade screwdriver

A0011219

Crosstip screwdriver

A0011221

Allen key

A0011222

Open-ended wrench

A0013442

Torx screwdriver

1.4 Registered trademarks

HART®

Registered trademark of the HART® FieldComm Group

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill the

following requirements:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Before beginning work, the specialist staff must have read and understood the instructions

in the Operating Instructions and supplementary documentation as well as in the

certificates (depending on the application)

‣Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

‣Being instructed and authorized according to the requirements of the task by the facility's

owner-operator

‣Following the instructions in these Operating Instructions

Incoming acceptance and product identification iTEMP TMT82

6 Endress+Hauser

2.2 Designated use

The device is a universal and user-configurable temperature transmitter with either one or

two sensor inputs for for a resistance thermometer (RTD), thermocouples (TC), resistance and

voltage transmitters. The head transmitter version of the device is intended for mounting in a

terminal head (flat face) as per DIN EN 50446. It is also possible to mount the device on a DIN

rail using the optional DIN rail clip. The device is also optionally available in a version suitable

for DIN rail mounting as per IEC 60715 (TH35).

If the equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Operational safety

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the hazardous

area (e.g. explosion protection or safety equipment):

‣Based on the technical data on the nameplate, check whether the ordered device is

permitted for the intended use in the hazardous area. The nameplate can be found on the

side of the transmitter housing.

‣Observe the specifications in the separate supplementary documentation that is an integral

part of these Instructions.

Electromagnetic compatibility

The measuring system complies with the general safety requirements as per EN 61010-1, the

EMC requirements as per the IEC/EN 61326 series and the NAMUR recommendations NE 21.

NOTICE

‣The device must only be powered by a power unit that operates using an energy-limited

electric circuit according to UL/EN/IEC 61010-1, chapter 9.4 and requirements of table 18.

3 Incoming acceptance and product identification

3.1 Incoming acceptance

1. Unpack the temperature transmitter carefully. Is the packaging or content damaged?

 Damaged components may not be installed as the manufacturer can otherwise not

guarantee compliance with the original safety requirements or the material

resistance, and can therefore not be held responsible for any resulting damage.

2. Is the delivery complete or is anything missing? Check the scope of delivery against your

order.

iTEMP TMT82 Incoming acceptance and product identification

Endress+Hauser 7

DELIVERY NOTE

A0037102

Does the nameplate match the ordering information on the delivery note?

TMT72

A0024858

Are the technical documentation and all other necessary documents provided? If

applicable: are the Safety Instructions (e.g. XA) for hazardous areas provided?

If one of these conditions is not satisfied, contact your Endress+Hauser Sales Center.

3.2 Product identification

The following options are available for identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

• Enter the serial number from the nameplate in the W@M Device Viewer

(www.endress.com/deviceviewer): All data relating to the device and an overview of the

Technical Documentation supplied with the device are displayed.

• Enter the serial number on the nameplate into the Endress+Hauser Operations App or scan

the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser Operations App:

all the information about the device and the technical documentation pertaining to the

device is displayed.

3.2.1 Nameplate

The right device?

Compare and check the data on the nameplate of the device against the requirements of the

measuring point:

Incoming acceptance and product identification iTEMP TMT82

8 Endress+Hauser

11-42V 012345678910

xx.yy.zz

TMT82- XXXXX/XX

iTEMP

Made in Germany 201x

D-87484 Nesselwang

Ser.no.:

FW:

Input:

12345678ABCDEFGH

Dev.Rev: x

Ext. ord. cd.:

XXXXXXXXXXXXX#

A0014561

 1 Nameplate of the head transmitter (example, Ex version)

1 Power supply, current consumption and extended order code

2 Serial number, device revision, firmware version and hardware version

3 Data Matrix 2D code

4 2 lines for the TAG name

5 Approval in hazardous area with number of the relevant Ex documentation (XA...)

6 Approvals with symbols

7 Order code and manufacturer ID

0044

iTEMP®TMT82

Made in Germany 2012 D-87484 Nesselwang

TAGXXXXXXXXXXX

Order code: TMT82-xxx/xx

Ext. ord. cd.: XXXXXXXXXXX

Ser. no.: XXXXXXXXX

Input: 12-42 V

Current cunsum.: 23,0 mA

EH 08.001X

II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C

II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C

Install per XA0xxxxT/09/a3/xx.xx

A0017924

 2 Nameplate of DIN rail transmitter (example, Ex version)

1 Product name and manufacturer ID

2 Order code, extended order code and serial number, DataMatrix 2D code, FCC-ID (if applicable)

3 Power supply and current consumption, output

4 Approval in hazardous area with number of the relevant Ex documentation (XA...)

5 Fieldbus communication logo

6 Firmware version and device revision

7 Approval logos

8 2 lines for the TAG name

iTEMP TMT82 Incoming acceptance and product identification

Endress+Hauser 9

3.2.2 Name and address of manufacturer

Name of manufacturer: Endress+Hauser Wetzer GmbH + Co. KG

Address of manufacturer: Obere Wank 1, D-87484 Nesselwang or www.endress.com

3.3 Scope of delivery

The scope of delivery of the device comprises:

• Temperature transmitter

• Mounting material (head transmitter), optional

• Hard copy of multi-language Brief Operating Instructions

• Functional Safety Manual (SIL mode)

•Additional documentation for devices which are suitable for use in the hazardous area (0

1), such as Safety Instructions (XA...), Control or Installation Drawings (ZD...).

3.4 Certificates and approvals

The device left the factory in a safe operating condition. The device complies with the

requirements of the standards EN 61 010-1 "Safety Requirements for Electrical Equipment for

Measurement, Control, and Laboratory Use" and with the EMC requirements as per the

IEC/EN 61326 series.

3.4.1 CE/EAC mark, Declaration of Conformity

The device meets the legal requirements of the EU/EEU guidelines. The manufacturer

confirms that the device is compliant with the relevant guidelines by applying the CE/EAC

mark.

3.4.2 Functional safety

The two device versions (head transmitter/DIN rail device) are optionally available for use in

safety systems as per IEC 61508.

• SIL 2: Hardware version

• SIL 3: Software version

3.5 Transport and storage

Carefully remove all the packaging material and protective covers that are part of the

transported package.

Storage temperature

• Head transmitter: –50 to +100 °C (–58 to +212 °F)

Option: –52 to +85 °C (–62 to +185 °F), Product Configurator, order code for "Test,

Certificate, Declaration", option "JN"

• DIN rail device: –40 to +100 °C (–40 to +212 °F)

Mounting iTEMP TMT82

10 Endress+Hauser

4 Mounting

4.1 Mounting requirements

4.1.1 Dimensions

24.1 (0.95)

33 (1.3)

! 44 (1.73)

! 7 (0.28)

! 5 (0.2)

A0007301

 3 Head transmitter version with screw terminals. Dimensions in mm (in)

A Spring travel L ≥ 5 mm (not for US - M4 securing screws)

B Mounting elements for attachable measured value display

C Interface for contacting measured value display

The same dimensions apply to the version with spring terminals. Exception: Height of

housing H = 30 mm (1.18 in).

17.5 (0.69) 114.9 (4.52)

100 (3.94)

112.8 (4.44)

A0017808

 4 DIN rail transmitter version. Dimensions in mm (in)

Andere Handbücher für iTEMP TMT82

Inhaltsverzeichnis

Andere Endress+Hauser Sender Handbücher

Endress+Hauser

Endress+Hauser Liquisys M CCM223 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT182 Bedienungsanleitung

Endress+Hauser

Endress+Hauser HMX50 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT125 Technische Daten

Endress+Hauser

Endress+Hauser Cerabar PMC71B Bedienungsanleitung

Endress+Hauser

Endress+Hauser cerabar S Bedienungsanleitung

Endress+Hauser

Endress+Hauser Commubox FXA291 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT80 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Mycom S CPM 153 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Flowmeter Proline 200 Technische Daten

Endress+Hauser

Endress+Hauser Proline 300 Modbus RS485 Technische Daten

Endress+Hauser

Endress+Hauser TMT122 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP PCP TMT 121 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquisys CUM 252 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquisys M CPM223 Bedienungsanleitung

Endress+Hauser

Endress+Hauser CM14 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT182 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquisys M CLM223 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquiline CM442R Bedienungsanleitung

Endress+Hauser

Endress+Hauser Liquisys M CUM 223 Bedienungsanleitung

Endress+Hauser

Endress+Hauser iTEMP TMT84 Technische Daten

Endress+Hauser

Endress+Hauser RMA42 Technische Daten

Endress+Hauser

Endress+Hauser iTEMP TMT86 Technische Daten

Endress+Hauser

Endress+Hauser Deltabar M PMD55 Technische Daten

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung

Endress+Hauser iTEMP TMT82 Technische Daten

Beliebte Sender Handbücher anderer Marken