Eneo VMC-17LCDM Bedienungsanleitung
Installation and User's Guide
All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein
17.0"/19.0" TFT LCD MONITOR
Installation and Operating Instructions
VMC-17LCDM
VMC-19LEDM
1. SAFETY INSTRUCTION
Follow this safety instruction to use the monitor properly and prevent the damage.
Keep this user’s guide book for later use.
This safety instruction has “Warning” & “Caution” as below
Warning - If the user does not follow this instruction,
it may cause the serious damage to the user.
Caution - If the user does not follow this instruction, it may cause the slight
damage to the user or cause some damages to the monitor.
Warning
Keep away the monitor from the
direct sunlight and a heating appliance.
Never put objects of any kind into
this product as they may result in
a risk of fire or electric shock.
Connect the power cord to the wall
outlet tightly. If the power cord or plug
are defective and the wall outlet is not
tight, please do not use them.
Never remove the back cover and
touch the inside of the monitor.
If you need a service, please
contact the service center.
2
Installation and User's Guide
Warning
Do not install this monitor on the outside
and near water. It may cause damage to
the product, electric shock and fire.
For cleaning do not use liquid cleaners.
Never touch the power plug with wet-hands.
When lightning and thundering, unplug the
monitor from the wall outlet and never touch
it.
When smoking and noising from the monitor,
unplug the product from the wall outlet and
contact a service center.
Unplug this product from the wall outlet, when
it does not operate for a long time.
W
WA
AR
RN
NI
IN
NG
G:
:
How to fix
Do not open this product as it contains high voltage inside.
It may create an electric shock.
If the user disassembles and remove the back cover, it does not make sure
to make up for the damage and do a service and exchange the monitor.
Installation and User's Guide
3
Cautions
Install this monitor some distance
from the wall and do not install unless
proper ventilation is provided.
Place this product on a stable place.
If not, it may fall, causing serious
damages to the monitor and people.
The openings must not be blocked by
curtain, rug or other similar surface.
Before carrying the monitor, turn it off and
unplug the signal cables and the power cord
from the wall outlet.
When carrying this monitor, be careful
not to damage the panel and drop it.
It may cause some trouble.
Take the power plug out from the wall
outlet.
Do not pull the cable. It may snap the inner-
wires and cause overheating and fire.
Installation and User's Guide
4
Cautions
Install this monitor about 50cm far from
the eyes and an angle of 0~15 degrees
below eyes. Too close installation may
cause having weak sight.
Do not press the LCD panel with hands or
the sharpened material hardly.
Do not use the chemical liquid for cleaning.
It may cause fading and breakage.
For cleaning, unplug the monitor from the
wall outlet. Do net use the liquid cloth.
Use the soft cloth.
Installation and User's Guide
5
2. FCC RF INTERFERENCE STATEMENT
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures.
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio, TV technician for help.
● Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void
the users authority to operate such equipment.
DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio
interference regulation of Canadian Department of communications.
6
Installation and User's Guide
7
Installation and User's Guide
2
1. SAFETY INSTRUCTION
1-1 Warning
1-2 Caution
6
2. FCC STATEMENT
3-1 Parts
3-2 How to Install
8
3. INSTALLATION
12
4. OSD MENU SETTING
TABLE OF CONTENTS
17
7. TROUBLESHOOTING
4-1 INPUT Select
4-2 MENU Selection
4-3 PICTURE MENU on OSD
4-4 VOLUME MENU on OSD
4-5 SYSTEM MENU on OSD
4-6 FUNCTION MENU on OSD
19
5. FEATURES
18
6. APPENDIX
8
Installation and User's Guide
3. INSTALLATION
3-1 Parts
LCD Monitor
VGA Cable Power Cable
Remote Controller
Battery User Manual
Adapter
9
Installation and User's Guide
3-2 How to Install
KEY BUTTON
SHORT KEY FUNCTION
OSD Key Function
Activates and exit the OSD
Select input source, and select the OSD menu
Move the OSD menu and auto adjustment of RGB source
Decrease the level of volume and move the previous menu
Increase the level of volume and select rhe OSD menu
Turns the power ON or OFF. There will be a few seconds
delay before the display appears. The power LED (next to the
power switch) lights with green when the power is turned ON.
The power is turned off by pressing the power switch again
and the power LED goes red.
10
Installation and User's Guide
CONNECTION
1
VIDEO-2 IN / OUT
DC12V
DC adapter input
VIDEO-2 signal input / looping out
4
2
AUDIO (PC)
Stereo audio input for VGA
6
8
5
3
7
VIDEO-1 IN / OUT
VIDEO-1 signal input / looping out
HDMI
HDMI signal input
AUDIO (VIDEO)
Stereo audio input for VIDEO or S-VIDEO
S-VIDEO
VGA
S-VIDEO signal input
VGA (PC RGB) signal input
1 2 3 4 5 6 7 8
Andere Handbücher für VMC-17LCDM
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Eneo Monitor Handbücher
Eneo
Eneo VMC-27LEDM Benutzerhandbuch
Eneo
Eneo VM-FHD24 Bedienungsanleitung
Eneo
Eneo VMC-19LEDMD Bedienungsanleitung
Eneo
Eneo VMC-17LCD-HPC1 Bedienungsanleitung
Eneo
Eneo PCS-19/DVR-08 Bedienungsanleitung
Eneo
Eneo VMC-10.4LED-CM Bedienungsanleitung
Eneo
Eneo VMC-8LCD-CP01 Benutzerhandbuch
Eneo
Eneo VM-FHD10M Bedienungsanleitung
Eneo
Eneo VM-FHD27MPA Bedienungsanleitung
Eneo
Eneo VM-FHD12M Bedienungsanleitung
Eneo
Eneo VM-FHD24PF Bedienungsanleitung
Eneo
Eneo VMC-8LCD-CM01 Bedienungsanleitung
Eneo
Eneo VMC-27LEDM Bedienungsanleitung
Eneo
Eneo VM-17PD Bedienungsanleitung
Eneo
Eneo VM-HD19M Montageanleitung
Eneo
Eneo VTD-1 Bedienungsanleitung
Eneo
Eneo VMC-8LCD-CM01B Bedienungsanleitung
Eneo
Eneo VMC-8.4LCD-CM Bedienungsanleitung
Eneo
Eneo VMC-17LCD-OPC3 Bedienungsanleitung
Eneo
Eneo VM-FHD10M Bedienungsanleitung
