Eneo PXD-2080Z03 B Montageanleitung

Full Manual

1/2.9" Network Camera

PXD-2080Z03 B

Table of contents

1. Safety Instructions and Notes….......................................................................................................

2. General Descriptions............................................................................……………………………...

3. Supplied Items......................................................................................……………………………...

4. Part names…………………………….…...................................................…………………………...

5. Installation Instructions......................................................................................……………………...

6. Setup Menu ……………............................................................................…………………………...

7. Specifications ………………………………………………..................................................................

8. Dimensional Drawings ……………………………………………..........................................................

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of

uninsulated "dangerous voltage" within the product's enclosure that

may be of sufficient magnitude to constitute a risk of electric shock

to persons.

Warning(NTSC version) -- This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Caution -- Any changes or modifications in construction of this device which are not expressly approved by

the party responsible for compliance could void the user's authority to operate the equipment.

Mains power quality should be that of a typical commercial environment. If the user of the model requires

continued operation during power mains interruptions, it is recommended that the model be powered from

an uninterruptible power supply (UPS) or a battery.”

Notice -- The images used in manual are processed to help comprehension and may

differ from actual appearance of the camera.

WARNING

NEVER USE THIS CAMERA

1. IN WATER.

2. IN AREA WHERE HAS SHOCK OR VIBRATION WHICH RESULTS IN THE

PROBLEM FOR AUTO FOCUSING.

Caution

To prevent electric shocks

and risk of fire hazards, do

NOT use other than specific

power source.

WARNING

1. Safety Instructions and Notes

• Please read this safety and operating instructions before putting the camera into

operation.

• Keep the manual in a safe place for later reference.

• Pay attention to safety when laying the connection cable and observe that the cable is not

subjected to

heavy loads, kinks or damage and no moisture can get in.

• Never open the device such as boards or lens.

The warranty becomes void if repairs are undertaken by unauthorized persons.

• Maintenance and repair have to be carried out only by authorized service centers.

• Use only a mild detergent to clean the housing.

• Keep clean the window surface from the dirt or dust, which may reflect the infrared light to

the lens at night..

• The camera should never be operated beyond the technical specifications. This can lead

to destruction.

• The camera should never be operated in water.

2. General Descriptions

This Network camera realizes the natural and crisp image as you see the scene in front of

you by adopting Auto Focus Full HD(1920x1080p) camera module.

Highly detailed pictures can be achieved and color reproducibility deserves attention.

With 3X Optical Zoom and 32X Digital Zoom,

- Offers the flexible observation

- Provides max. 96X zoom

With ICR mechanism,

- Enhances its sensitivity about 10X at night time

- Can accepts the infrared light

With 24VAC/12VDC dual power design,

- Offers the flexibility of installation

- Ensures the reliability

Main features are;

•Onvif / PSIA Conformance

•Optical 3X Auto Focus Zoom • Digital 32X Zoom

•f3~9mm, 3X Day & Night Zoom Lens

•1920x1080p(30fps/25fps)

•Wide Dynamic Range

•Sense Up(~x8) / AGC(0~20) / 3D Noise Reduction

•SMART MOTION ZOOM(Automatic Zoom IN/OUT when motion is detected)

•Pointing Zoom which enables the flexible zooming at any area

•Motion Detection / Motion Deblur / Privacy Mask / Defog

•Focusing Status Indicator on Screen

- (Blue) Focusing in process

- (White) Focusing Completed

•Pixel Defect Compensation

•ID / TITLE / ZOOM RATIO Display

•H / V / HV FLIP

•Lens Refresh / Lens Initializing Set / LSC(Lens Shade Compensation)

•Enhanced Sensitivity by DSS technology

•Menu Control via either Local Joystick or WEB

•OSD Menu & CVBS Video Sub-out for Easy installation and Maintenance

•H.264/MJPEG dual streaming with TI DM365/368 engine

•Full duplex 2 way Audio, Alarm IN/OUT

•Max 30fps live view @ 1920x1080p

•MICRO SD memory card slot for Local recording

•PoE (Power Over Ethernet), IEEE 802.3af

•Input voltage: 24VAC/12VDC dual type of Local power

•Circuit protection against faulty connection in Power Polarity

•Isolated power supply against ground loop problem.

•Built in cooling Fan and Heating function

•Anti-Scratch Hard Coated Clear Bubble

•Changeable surface mount and flush mount

•Perfect 3-Axis gimbal

•2 High power LEDs

• IP 67 / IK 10 Protection

3. Supplied Items

• 1x MegaPixel Network AF Zoom Camera

• 1x Installation and Operating Instructions

• 1x ①Pipe hole cap

• 1x ②Pipe Spacer

• 1x ③L-shape hex wrench

• 3x ④Wrench Bolt for surface mount

• 4x ⑤Anchors

• 4x ⑥Mount screws

• 1x ⑦BM Screw

• 1x ⑧Sub-out cable

• 1x ⑨Coupler for RJ45 Cable

• 1x ⑩EMI Ferrite Core

①

②

③

⑤

⑥

⑧

⑦

⑨

④

⑩

4. Control and Part names

ⓐLens

ⓑLight sensor for IR LEDs

ⓒIR LEDs

ⓓIP RESET

ⓔMICRO SD Card Slot

ⓕRTx Status Indicator

ⓖOSD control joy stick

ⓗVideo Sub-output

ⓘMount holes(x3) for dome base

ⓙClear bubble

ⓚRing cover fixing screws(x3)

ⓛRing cover

ⓜSurface mount holes(x4)

ⓝDome base fixing screw taps(x3)

ⓞPipe hole

ⓟPipe spacer

ⓕ

ⓖ

ⓘ

ⓗ

ⓐ

ⓑ

ⓒ

ⓔ

ⓞ

ⓝ

ⓜ

Surface Mount Base

ⓙ

ⓚ

ⓛ

ⓟ

ⓓ

Dome Bubble Assembly

5. Installation

5.1 Installation Instructions

•Make sure the power is removed before the installation.

•Follow the order for applying power.

First, connect the low voltage (AC24V or DC12V), then plug the AC adapter to AC outlets to avoid an

improper reset from power jitter and a damage from the surge voltage when no load.

Joy stick

VIDEO

SUB-OUT

connector

WARNING NEVER USE THIS CAMERA

1) in WATER.

2) in area where has SHOCK or VIBRATION which results in the problems for Auto Focus operation.

Zoom & Focus Adjustment

(Only works when OSD Menu is not operating)

▲Zoom In

▼Zoom Out

◀Focus Near

▶Focus Far

SYMBOL descriptions for joystick operation;

-▲,▼,◀,▶denotes the directions of Joystick lever

operation.

☟

denotes the long press down straightly

for about 2 seconds.

IP Reset (Press over 10 sec by stick driver)

5.2 Surface mount

Surface mount

base

⑥Mount screws

and ②pipe hole

cap for surface

mount base

Dome base

assembly

④Wrench bolts

for fitting to

surface mount

base

Dome bubble

assembly

L-Wrench

Quick installation guides;

1. Locate the mounting template at the installation position

and drill the ceiling or wall if needed.

2. Place Surface mount base on pre-drilled position and fix it

through

ⓙ

Surface mount holes(x4) by using ⑥Mount screws.

Assemble the cable pipe, otherwise tighten

①

pipe hole cap.

3. Open Dome bubble assembly by loosening

ⓘ

Ring cover

fixing screws(x3)

CAUTION

Extreme care should be taken NOT to scratch the dome

surfaces and to protect it from dirt or dust at any time.

4. ⓕMount holes(x3) for dome base and ⓚhole should be

aligned before fixing Dome base assembly to Surface mount

base by using ④Wrench bolts. And tighten ④wrench bolts

5. Route the power/ video cable to the connecting place.

CAUTION

Care should be taken the cable is NOT to be damaged,

kinked or exposed in the hazardous area.

6. Set the camera’s angle (Pan, Tilt, inclination)

7. Adjust ZOOM/FOCUS by OSD menu or manual

8. Put Dome bubble assembly over Dome camera assembly and

tighten

ⓗ

Ring cover fixing screws(x3) by using

③

L-shape hex

wrench

CAUTION

Tighten enough

ⓗ

Ring cover fixing screws(x3) so that

there should be NO gap between

ⓔ

Lens and

ⓖ

Clear bubble to avoid the light inflow from IR LEDs.

Ceiling or wall

5.3 Flush mount

⑥Mount screws

Dome base

assembly

Quick installation guides;

1. Locate the mounting template at the installation position

and drill the ceiling or wall if needed.

2. Open Dome bubble assembly by loosening

ⓘ

Ring cover

fixing screws(x3)

CAUTION

Extreme care should be taken NOT to scratch the dome

surfaces and to protect it from dirt or dust at any time.

3. Place Dome base assembly on pre-drilled position and fix it

through

ⓕ

mount holes(x3)

by using ⑥Mount screws.

(Use three screws only out of ⑥Mount screws(4x))

4. Route the power/ video cable to the connecting place.

CAUTION

Care should be taken the cable is NOT to be damaged,

kinked or exposed in the hazardous area.

5. Set the camera’s angle (Pan, Tilt, inclination)

6. Adjust ZOOM/FOCUS by OSD menu or manual

7. Put Dome bubble assembly over Dome camera assembly and

tighten

ⓗ

Ring cover fixing screws(x3) by using ③L-shape hex

wrench

CAUTION

Tighten enough

ⓗ

Ring cover fixing screws(x3) so that

there should be NO gap between

ⓔ

Lens and

ⓖ

Clear bubble to avoid the light inflow from IR LEDs.

Ceiling or wall

Dome bubble

assembly

L-Wrench

Inhaltsverzeichnis

Andere Eneo Sicherheitskamera Handbücher

Eneo

Eneo MEB-55M2812M0A Bedienungsanleitung

Eneo

Eneo IED-62F0036M0A Bedienungsanleitung

Eneo

Eneo IPD-75M3610M0A Bedienungsanleitung

Eneo

Eneo IND-32F0016P0A Bedienungsanleitung

Eneo

Eneo IED-62F0036P0A Bedienungsanleitung

Eneo

Eneo ICB-68M3611M5A Bedienungsanleitung

Eneo

Eneo MEB-62V2713P0A Bedienungsanleitung

Eneo

Eneo IPP-72A0023MIA Bedienungsanleitung

Eneo

Eneo IPP-62A0012M0A Bedienungsanleitung

Eneo

Eneo HDD-2018PTZ1080 Bedienungsanleitung

Eneo

Eneo INP-75A0033MIA Bedienungsanleitung

Eneo

Eneo NXD Series Bedienungsanleitung

Eneo

Eneo VKCD-1321SFM/MF Bedienungsanleitung

Eneo

Eneo NXP-880F21 Bedienungsanleitung

Eneo

Eneo HDD-2080M2810IR D Bedienungsanleitung

Eneo

Eneo VKC-1367IR-1850 Bedienungsanleitung

Eneo

Eneo HDD-2080Z03IR D Bedienungsanleitung

Eneo

Eneo ICB-62M2713MAA Bedienungsanleitung

Eneo

Eneo IPD-72M2713MAA Bedienungsanleitung

Eneo

Eneo Fastrax III EDC-3362 Bedienungsanleitung

Eneo

Eneo IPC-53M2812M0A Bedienungsanleitung

Eneo

Eneo MED-62V2713M0A Bedienungsanleitung

Eneo

Eneo ICB-73M2712MWA Bedienungsanleitung

Eneo

Eneo MEB-62F0036P0A Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung