EnGenius EWS850-FIT Bedienungsanleitung

EWS850-FIT

EWS850-FIT Quick Start Guide

Quick Start Guide

EnGenius Fit Wi-Fi 6 2×2 Outdoor Wireless

Access Point

Quick Start Guide

Introduction

This Quick Start Guide is designed to guide you through the

installation of the Fit 2x2 access point, model EWS850-FIT,

including hardware mounting and configuration.

FIT Bridge Outdoor

Access Point

Mounting

Screw Kit x2

Mounting

Bracket

Pole Mounting

Strap x2

Ground Wire &

Screw Set

Product CardDetachable Antena:

2.4GHz Antenna x2

5GHz Antenna x2

Package Contents

• Wi-Fi 6 technology for high-performance Wi-Fi in high-density,

multi-device environments.

• Two spatial streams support up to 1,200 Mbps (5GHz) & 574

Mbps (2.4GHz).

• Multiple applications for cloud and on premises solutions.

Model: EWS850-FIT

System Requirements

• Google Chrome (57.0.2987.110 and later)

• Microsoft Edge (80.0.361.103 and later)

• Mozilla Firefox (52.0 and later)

Web Browser

EWS850-FIT Quick Start Guide

Hardware Overview

Reset Button:

Reset to default: Press and hold the reset button on the PoE adaptor for over 60 seconds, and the LED (PWR)

will start Fast Flashing (0.2 sec). Then, the device will be reset to factory default settings.

Bottom Cover

(Aluminum

Die-Casting)

Mounting

Holes Detachable Antennas

(SMA Type)

Top Cover

(UL Certified Plastic)

LED

Indicaters

LAN- 2.5 Gigabit Ethernet Port

(802.3at PoE)

LEDs

STATUS LED COLOR LED BEHAVIOR

Connecting to the management

(FitXpress/FitController)

PWR (Orange) Flashing (0.5 Sec.)

Management Connected

(FitXpress/FitController/Standalone)

PWR (Orange) Solid On

LAN Connected LAN (1G) LAN (2.5G) Solid On

LAN Transmitting LAN (1G) LAN (2.5G) Flashing

2.4GHz Radio On 2.4GHz (Green) Solid On

2.4GHz Transmitting 2.4GHz (Green) Flashing

5GHz Radio On 5GHz (Green) Solid On

5GHz Transmitting 5GHz (Green) Flashing

Firmware Upgrading PWR LAN 2.4GHz 5GHz Flashing (0.5 Sec.)

Reset to Default PWR (Orange) Fast Flashing

AP Location Mode PWR LAN 2.4GHz 5GHz Flashing (1.5 Sec. on ->0.5 Sec. off)

EWS850-FIT Quick Start Guide

1. Determine where the Access Point will be placed and

mark the location on the surface for the two mounting

holes. Use the appropriate drill bit to drill two 8.1mm

diagram and 26mm-deep holes on the marks.

2. Screw the Anchors into the holes until they are flush

with the wall.

3. Fasten the Mounting Bracket with the included

Screws into the Anchors.

Hardware Mounting

Wall Mount

The access point can be mounted on the Wall and Pole, and

please perform the steps for the appropriate installation.

Anchors Wall

Screws

Anchors

Wall

4. Hang the Access Point against the wall on the

Mounting Bracket. 5. Secure the Access Point on the Mounting Bracket

with the secure lock on the side.

Mounting Bracket

Wall

FIT Bridge Outdoor

Access Point

EWS850-FIT Quick Start Guide

1. Thread the open end of the Pole Mounting Strap

through the two tabs on the Mounting Bracket.

Pole Mount

2. Lock and tighten the Pole Mounting Strap to secure

the Mounting Bracket onto the pole.

3. Hang the Access Point onto the Mounting Bracket.

4. Secure the Access Point on the Mounting Bracket with the secure lock on the side.

Pole Mounting

Strap

Mounting

Bracket

Mounting

Bracket

Pole Mounting

Strap

EWS850-FIT Quick Start Guide

EnGenius Fit AP devices can be powered by any of the following:

• EnGenius Fit PoE switches or 802.3af/ 802.3at PoE+ compliant switches

• EnGenius PoE Injector (EPA5006GR)

Caution: Do not use both power sources at the same time.

Powering EnGenius Fit AP

Connecting to a PoE Switch

Connect the Ethernet cable from the EnGenius Fit AP directly to the PoE port of the PoE switch.

EnGenius Fit

Access Point

Ethernet Cable

AP is power by a PoE Switch

EnGenius Fit

PoE Switch

Powering with a PoE Injector

(A) Connect one end of the Ethernet cable into the LAN (PoE) port of EnGenius FIT AP and the other end to the PoE port

on the PoE Adapter.

(B) Connect the power cord with the PoE Adapter and plug the other end into an electrical outlet.

network.

Note: Please make sure to use Cat6 RJ45 Ethernet cables.

EnGenius Fit

Access Point

EnGenius

PoE Injectors

Gateway/Router/

Network Switch

(A)

(B)

EWS850-FIT Quick Start Guide

On-Premises Management

Management Plane

Cloud Management

EnGenius Fit provides flexible options to manage your devices based on your network planning and deployment.

Option A: Cloud Management

Option B: On-Premises Management

Option C: Standalone Configuration

Manage and monitor the Access Point through the FitXpress Platform with a mobile app or through the web portal.

FitXpress App (iOS/ Android)

If you want to manage the device in on-premises mode, you need an onsite management station running the FitController

connected to the same Layer 2 network.

FitController

FitController is a custom-built appliance with optimized network management software installed to ease onsite

deployment without manual server configurations.

Scan to download FitXpress app

Standalone Configuration

Using your computer, you can connect to the same network (subnet) as the Access Point and use the web browser to

access the device’s local web GUI page for configurations whenever the device is set to Standalone mode.

Download the FitXpress mobile app App Store click here

Download the FitXpress mobile app Google Play click here

EWS850-FIT Quick Start Guide

Option A: Cloud Management with FitXpress

Step 1: Connecting Ethernet

Connect the Ethernet cable from the EnGenius Fit AP directly to the

DHCP-enabled network and make sure the AP can reach the Internet.

Gateway/Router/ Network Switch

DHCP-Assigned IP EnGenius Fit

Access Point

Internet

Step 2: Register Device

You can register the access point with the FitXpress app.

1. Open the FitXpress mobile app and create an account.

2. Login and go to the Devices section. Click the Add (+) button.

3. Scan the QR code on the back of the device via the app.

Scan QR-code for device registration

EWS850-FIT Quick Start Guide

4. If the camera successfully scans the QR code, the app will display the device information. You can tap “Register” to

complete the registration.

Step 3: Connect to FitXpress

Once the device is powered on and ready to connect to the Internet, the PWR LED will stay Solid On, which means the

device is now connected to the FitXpress platform. It will automatically download the default configuration settings from

FitXpress for automated provisioning.

When the Access Point is connected to the FitXpress Platform for the first time, it will automatically check the latest

firmware version available. If a firmware upgrade is required, it might take 8~10 minutes to complete the process. All LED

indicators will be Flashing (0.5 sec) till the process is finished.

Step 4: Manage with the FitXpress

EWS850-FIT Quick Start Guide

EnGenius Fit

PoE Switch

Gateway

FitController EnGenius Fit

Access Point

Option B: On-premises Management with FitController

Step 1: Connecting Ethernet

Connect the Ethernet cable from the EnGenius Fit AP directly to the DHCP-enabled network, which is the same Layer-2

network as FitController.

Step 2: Log in to the FitController

Launch your web browser to access the login page of FitController and create an account. Enter the email address and

password that you created and click Sign In.

The FitController default IP address in DHCP client mode will get an IP address (e.g. X.X.X.X:8080) from the DHCP

server. If FitController cannot get an IP address from the DHCP server, the default IP address will be 192.168.1.250:8080.

Internet

EWS850-FIT Quick Start Guide

Step 5: Manage with FitController

Navigate to the left side menu to configure & manage your network and view network statistics using the FitController

management interface.

Step 4: Pairing the Device

1. Go to access point or switch list.

2. Select the newly added device and click “Pairing” to allow the access point to build an encrypted connection between

the device and FitController.

Step 3: Register Device and Assign to Network

1. Go to the system > Inventory page and click “Register Device (+)”.

2. FitController will list all EnGenius Fit devices discovered from the same L2 network in the Pending Approval section.

Select the device and Click “Register” to add to inventory. You can also tap “Manually” tab and register Fit device by

entering Serial Number.

3. From the Inventory page, Select the newly added device and click “Assign to Network” to add the device to your

personalized network.

Inhaltsverzeichnis

Andere EnGenius Drahtloser Zugangspunkt Handbücher

EnGenius

EnGenius EOC1650 Bedienungsanleitung

EnGenius

EnGenius ECB7510 Bedienungsanleitung

EnGenius

EnGenius ENH500 Bedienungsanleitung

EnGenius

EnGenius EAP150 Bedienungsanleitung

EnGenius

EnGenius ECB600 Bedienungsanleitung

EnGenius

EnGenius EOC1650 Bedienungsanleitung

EnGenius

EnGenius ENH710EXT Bedienungsanleitung

EnGenius

EnGenius ENH900EXT Bedienungsanleitung

EnGenius

EnGenius EAP9550 Bedienungsanleitung

EnGenius

EnGenius EAP 11AC Series Bedienungsanleitung

EnGenius

EnGenius ECB300 Bedienungsanleitung

EnGenius

EnGenius ECB7510 Bedienungsanleitung

EnGenius

EnGenius ECB-3220 Bedienungsanleitung

EnGenius

EnGenius ENS202EXT Bedienungsanleitung

EnGenius

EnGenius ENS202 Bedienungsanleitung

EnGenius

EnGenius EOC1650 Bedienungsanleitung

EnGenius

EnGenius EOC-5610 Bedienungsanleitung

EnGenius

EnGenius ENH700EXT Bedienungsanleitung

EnGenius

EnGenius X-TRA RANGE ERB300H Bedienungsanleitung

EnGenius

EnGenius EOC5611P Bedienungsanleitung

EnGenius

EnGenius EW310AP Bedienungsanleitung

EnGenius

EnGenius EWS550AP Bedienungsanleitung

EnGenius

EnGenius EOC-2610 Bedienungsanleitung

EnGenius

EnGenius ENS500EXT Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung