Enttec Playback Bedienungsanleitung
This page Blank
ENTTEC Wing User Manual 2
Table of Contents
This page Blank..........................................................................................2
Contents........................................................................................................4
Contacting ENTTEC.....................................................................................4
Warranty.......................................................................................................5
Introduction...................................................................................................
Features.........................................................................................................
Shortcut Wing..........................................................................................
Playback Wing.........................................................................................7
Programming Wing..................................................................................7
Getting Started ............................................................................................7
Ethernet Connection.................................................................................7
Using the wing with LightFactory................................................................8
Connecting the wing................................................................................8
..................................................................................................................9
Mapping the wing in LightFactory.........................................................10
The Programming Wing and LightFactory............................................11
Configuring the wing..................................................................................2
NMU-based Configuration.........................................................................2
Art-Net Mode .............................................................................................2
Updating the firmware...........................................................................30
Appendix 1..................................................................................................34
Appendix 2..................................................................................................3
ENTTEC Wing User Manual 3
Contents
When you open the packaging, you should find these items in the box:
•ENTTEC Wing
•User Manual
•9V Power supply (pn: 79104)
•Cross over cable (pn:79101)
•Straight cable (pn:79102)
•IP address Label
•CD
If one of these items is missing please contact your local dealer.
The user manual for all ENTTEC Wings is the same. Please
refer to the se tion relating to that spe ifi produ t.
Contacting ENTTEC
To contact us, please send an email to: [email protected]
Tel: + 1 3 97 3 5755 GMT+10
Fax: + 1 3 97 3 5 88
To write us:
ENTTEC Pty Ltd
Unit 17/5 Samantha Court
Knoxfield, VIC 3180
AUSTRALIA
ENTTEC Wing User Manual 4
Warranty
ENTTEC warrants that the product it manufactures and sells will be free
from defects in materials and workmanship for a period of 1 year from the
date of shipment from an authorized ENTTEC wholesaler. If the device
proves defective within the respective period, ENTTEC will repair or
replace the defective hardware at its sole discretion. If the failure is due to
an operator error the user accepts to pay for any charge relating to the
diagnosis of the hardware, faulty parts or shipping from our factory.
ENTTEC makes no warranty of any kind, express or implied,
in luding without limitation the implied warranties of mer hantability
and fitness for a parti ular purpose. In no event shall ENTTEC be
liable for indire t, spe ial or onsequential damages.
Opening the unit voids the warranty as des ribed above.
ENTTEC Wing User Manual 5
Introduction
Thank you for buying the ENTTEC Wing. At ENTTEC we are proud of
our products and we hope you will enjoy them as much as we enjoy
making them.
This manual was written primarily to describe operation of the ENTTEC
Wing with ENTTEC LightFactory software. This is referred to as the
ENTTEC MODE of operation. There is another mode of operation, called
the Art-Net mode, which is covered in a separate section. Finally, other
programs are planning to support the wings, and their operation as it
relates to those software titles will be explained in full by those vendors.
Firstly, un-pack the unit from the box.
On the rear panel, you will find :
•RJ45 Ethercon connector for a 10Base-T Ethernet connection
•Status Led indicating if the device is powered up and running
•Activity Led indicating the presence of packets on the network
•Link led indicating the presence of an Ethernet connection
•9V AC or DC power connector
The unit has no power switch and can be left on continuously.
Features
Shortcut Wing
•Ethernet Interface
•0 High quality Cherry MX Keys
•2 Digit 7 Segment LED display
•PAGE UP & PAGE DOWN Keys
•Upgradeable firmware
ENTTEC Wing User Manual
Playback Wing
•Ethernet Interface
•40 High quality Cherry MX Keys
•10 High Quality 0mm Faders
•2 Digit 7 Segment LED display
•PAGE UP & PAGE DOWN Keys
•Large GO & BACK Keys
•Upgradeable firmware
Programming Wing
•Ethernet Interface
•2 High quality Cherry MX Keys
•PAGE UP & PAGE DOWN Keys for Encoder
•9 Window Keys
•25 Operational & Function Keys
•19 Key Numeric Keypad
•4 Arrow Keys and Backspace
•3 Rotary Encoders
•4 line 20 character LCD Display
•Upgradeable firmware
Getting Started
Ethernet Connection
Firstly, you need to connect your wing and the computer running
LightFactory. If you have an available Ethernet port on your computer, you
can connect your Wing directly to your computer using a cross-over patch
lead. If your Ethernet port is already in use, or you are using more than one
Wing, you will need to connect the computer and the Wing/s to an Ethernet
Hub or Switch using a standard Ethernet patch cable. Do not use power
over Ethernet hubs or switches.
Once you’ve connected the Wing and the computer the Link LED should
ENTTEC Wing User Manual 7
light up immediately. If not, check the Ethernet cable you’ve used is the
correct type (ie – cross over or straight through) and is in good working
order, and the computer and hub/switch are functioning correctly.
You may see the Activity LED blinking occasionally if there is activity on
the Ethernet network.
Using the wing with ightFactory
Connecting the wing
Make sure the wing is connected correctly and powered up.
Start Light factory and go to the File->System Properties->External Wings
This screen will display the connected wings.
In the event you see a warning on the screen, this is due to the fact the IP
ranges of your computer and the wing do not match. This means for
ENTTEC Wing User Manual 8
example that the wing would have an IP of 10.7.81.1 1 and your computer
192.1 8.0.23. In this case both devices are not on the same subnet and
cannot talk to each other properly.
You can either change the IP of the wing to be in the same subnet as the
computer (see “Configuring the Wing” on page 11 for details), or change
the IP of the computer to be in the same subnet as the wing.
For example if the wing has an IP of 10.7.81.1 1 , you would set the
computer to ip 10.7.81.1 with a net mask of 255.255.255.0
You can check your computer’s IP address by clicking on 'Start' then 'Run',
type cmd (enter). This will open a command window, then type: ipconfig
and press enter
This will display the IP address of your computer.
ENTTEC Wing User Manual 9
Mapping the wing in LightFactory
The wing is automatically configured by LightFactory:
–Playback wing:
–Page 0, Fader 1 on the wing is linked to Submaster 1 and Playback
1 in LightFactory.
–Page 1, Fader 1 corresponds to Submaster 101 and Playback 11.
–Page 2, Fader 1 corresponds to Submaster 201 and Playback 21.
–etc.
–Shortcut Wing:
–Page 0, Button 1 is linked to Shortcut 1 in LightFactory.
–Page 1, Button 1 corresponds to Shortcut 101
–Page 2, Button 1 corresponds to Shortcut 201
–etc
–Programming Wing
–Paging does not apply, except for the assignment of Attributes to
the Encoders, which are a special case and which are explained by
text display on the wing's LCD readout when the feature is in use.
–This wing has many other features that are unique to it which may
require further explanation. If using it with LightFactory, those
features are discussed in the next section. For other software titles
that may support the wing as well, please consult their User Manual
for equivalent information pertaining to that software.
ENTTEC Wing User Manual 10
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Enttec Controller Handbücher
Enttec
Enttec PIXEL PORT Bedienungsanleitung
Enttec
Enttec OCTO MK2 Bedienungsanleitung
Enttec
Enttec PIXELATOR MINI Benutzerhandbuch
Enttec
Enttec PIXELATOR MINI Gebrauchsanweisung
Enttec
Enttec OCTO MK2 Bedienungsanleitung
Enttec
Enttec PIXELATOR MINI Bedienungsanleitung
Enttec
Enttec DIN-ODE MK2 Bedienungsanleitung
Enttec
Enttec Evo Bedienungsanleitung
Enttec
Enttec PIXELATOR MINI Bedienungsanleitung
Enttec
Enttec DATAGATE MK2 Gebrauchsanweisung
Enttec
Enttec DMXEtherGate Mk2 Bedienungsanleitung
Enttec
Enttec Pixel Octo Bedienungsanleitung
Enttec
Enttec Open DMX Ethernet Bedienungsanleitung
Enttec
Enttec Pixelator Bedienungsanleitung
Enttec
Enttec S-PLAY NANO Bedienungsanleitung
Enttec
Enttec Din Pixie Bedienungsanleitung
Enttec
Enttec DMXPLAYBACK MK2 Bedienungsanleitung
Enttec
Enttec S-PLAY Bedienungsanleitung
Enttec
Enttec OCTO MK2 Bedienungsanleitung
Enttec
Enttec OCTO Bedienungsanleitung
