Enviro 50-1095 Bedienungsanleitung

PELLET STOVE

Bern

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE

OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY

OR EVEN DEATH

Contact your building or fire officials about restrictions and installation

inspection requirements in your area.

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED

PAPER.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

TECHNICAL MANUAL



50-1095

Introduction...................................................................................................................................3

Rating Label Location................................................................................................................3

Important Safety Data...............................................................................................................3

Safety Warnings And Recommendations.....................................................................................3

Installation.....................................................................................................................................5

Deciding Where to Locate your Pellet Appliance..........................................................................5

Removing Pellet Stove From Pallet.............................................................................................5

Appliance Dimensions and Specifications .................................................................................6

Clearances to Combustibles.......................................................................................................7

Alcove Clearances.....................................................................................................................7

Vent Termination Requirements.................................................................................................8

Exhaust Location......................................................................................................................9

Corner Through Wall Installation................................................................................................9

Horizontal Exhaust Through Wall Installation.............................................................................10

Through Wall With Vertical Rise and Horizontal Termination Installation - Freestanding................11

Inside Vertical Installations......................................................................................................12

Outside Vertical Installations....................................................................................................12

Hearth Mount Installation........................................................................................................13

Exterior Mounted Exhaust Blower.............................................................................................15

Typical Through Wall With Exterior Blower Kit Installation - Horizontal Termination......................16

Typical Through Wall With Exterior Blower Kit Installation - Vertical Termination..........................17

Thermostat Installation............................................................................................................18

Optional Slider/Damper Installation..........................................................................................18

Slider/Damper Set-Up..............................................................................................................19

Optional Panel Kit....................................................................................................................20

Optional Fan Kit.......................................................................................................................21

Troubleshooting............................................................................................................................22

Fuses.....................................................................................................................................24

Wiring Diagram.............................................................................................................................25

Parts List......................................................................................................................................26

Parts Diagram - Components..........................................................................................................28

Parts Diagram - Steel.....................................................................................................................29

Warranty...............................................................................................................................30

Installation Data Sheet..................................................................................................................31

Table of Contents

Introduction

* This manual is designed for the technician in conjunction with the owner’s manual. *

RATING LABEL LOCATION:

The rating label is located on the back of the unit.

IMPORTANT SAFETY DATA:

Please read this entire Owner’s Manual before installing or operating this ENVIRO Pellet

Stove. Failure to follow these instructions may result in property damage, bodily injury

or even death. Contact your local building or fire official to obtain a permit and any information on

installation restrictions and inspection requirements for your area.

To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering

to the installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information

with regards to your local building codes and installation restrictions.

Be sure to maintain the structural integrity of the home when passing a vent through walls, ceilings, or

roofs.

The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive

chimney pressure. It is very important to ensure that the exhaust system be sealed and airtight. The ash

pan and viewing door must be locked securely for proper and safe operation of the pellet stove.

Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper

combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by

adjusting the slider damper located on the left side of the stove.

When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the

home and bolted to the floor. Make sure that the structural integrity of the home is maintained and all

construction meets local building codes.

Minor soot or creosote may accumulate when the stove is operated under incorrect conditions such as an

extremely rich burn (black tipped, lazy orange flames).

If you have any questions with regard to your stove or the above-mentioned information, please feel free

to contact your local dealer for further clarification and comments.

SAFETY WARNINGS AND RECOMMENDATIONS:

Caution: Do not connect to any air distribution duct or system.

Do not burn garbage or flammable fluids such as gasoline, naptha or engine oil.

Unit hot while in operation. Keep children, clothing and furniture away. Contact

may cause skin burns.

SOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which

will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the

house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/

damper as needed to ensure proper combustion. See: “INSTALLATION SLIDER/DAMPER SETTING”.

Introduction

ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be

grounded. The grounded electrical cord should be connected to a standard 220-240 volts,, nominal

average 0.8 Amps (1.4 Amps peak), 50 hertz electrical outlet and also must be accessible. If this power

cord should become damaged, a replacement power cord must be purchased from a qualified ENVIRO

dealer. Be careful that the electrical cord is not trapped under the appliance and that it is clear of any hot

surfaces or sharp edges. This unit’s maximum power requirement is 184 watts (322 watts peak).

GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove

with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an ENVIRO

dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is

hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner,

or take a damp paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the

glass.

FLAMMABLE LIQUIDS: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter

fluid, or similar liquids to start or “freshen up” a fire in the heater. Keep all such liquids well away from

the heater while it is in use.

SMOKE DETECTOR: Smoke detectors should be installed and maintained in the structure when

installing and operating a pellet burning appliance.

OPERATION: The ash pan and door must be closed securely for proper and safe operation of the pellet

stove. Also ensure all gaskets on the door are checked and replaced when necessary.

INSTALLATION: Be sure to maintain the structural integrity of your home when passing a vent through

walls, ceilings, or roofs. It is recommended that the unit be secured into its position in order to avoid any

displacement.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

FRESH AIR: Outside Fresh Air is optional. Consider all large air moving devices when installing your unit

and provide room air accordingly. Limited air for combustion may result in poor performance, smoking

and other side effects of poor combustion.

If you have any questions with regards to your stove or the above-mentioned information, please feel

free to contact your local dealer for further clarification and comments.

SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF

YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED

FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, SHERWOOD

INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

Installation

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:

1. Check clearances to combustibles.

2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may

be obtained from a ventilated crawlspace.

3. Do not install the stove in a bedroom.

4. You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry

or metal chimney (must be lined if the chimney is over 6” (15 cm) diameter, or over 28 inches² (180

cm²) cross sectional area). An interior vent can be used with approved pipe passing through the

ceiling and roof.

5. Locate the stove in a large and open room that is centrally located in the house. This will optimize

heat circulation.

6. The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach the

nearest electrical outlet.

REMOVING PELLET STOVE FROM PALLET:

1. Remove the right and left hand cabinet sides by

loosening the three (3) T-20 Torx screws on the

back of the each panel.

2. Remove the screw located on the front of the

cabinet side, below the louvers and loosen the

screw behind the ash door.

3. Using a 5/16” socket of flat head screwdriver,

remove the three (3) wood screws that are holding

the bottom of the stove to the pallet. There is one

(1) screw behind each side panel and one (1) at the

back behind the back grill.

4. Close the side panels.

5. Install the four (4) leveling legs into the nuts in the

base.

Figure 1: Screws to take out to remove stove from

pallet.

Installation

APPLIANCE DIMENSIONS AND SPECIFICATIONS:

Figure 2: Dimensions of Bern.

15 1/2"

(393 mm)

18 7/8"

(481 mm)

17 1/2"

(444 mm) 19 5/8"

(497 mm)

17 7/8"

(455 mm)

34 3/4"

(883 mm)

Weight (with full hopper): 238 lb (108 Kg)

Hopper Capacity: up to 52 lb (23.6 Kg)

Voltage: 220 - 240 V

Max Current: 1.4 Amps

Consumption on High: 2.9 lb/hr (1.3 Kg/hr)*

Consumption on Low: 0.9 lb/hr (0.4 Kg/hr)*

(Note: Consumption will vary with the type of

fuel used.)

Installation

CLEARANCES TO COMBUSTIBLES:

Use a hearth pad that extends 6 inches (15 cm) in front of the unit when installing on a combustible

floor.

ALCOVE CLEARANCES:

This unit may be installed in an alcove. Maintain

these clearances to combustibles.

Minimum Alcove width 48 inches (122 cm)

Minimum Alcove height 48 inches (122 cm)

Maximum Alcove depth 48 inches (122 cm)

Install vent at clearances specified by

the vent manufacturer.

Side Wall

Back Wall

AdjacentWall

(20cm)

(8cm)

4" (8cm)













These dimensions are minimum clearances but it

is recommended that you ensure sufficient room

for servicing, routine cleaning and maintenance.

Side wall to unit 8 inches (20 cm)

Back wall to unit 4 inches (10 cm)

Corner to unit 4 inches (10 cm)

Figure 3: Bern Clearance to Combustibles.

Figure 4: Bern Minimum Alcove Size.

fumes such as stairwells, covered breezeway, etc.

2. Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shielding

or guards may be required.

3. Termination must exhaust above the inlet elevation. It is recommended that at least five feet of

vertical pipe be installed outside when the appliance is vented directly through a wall, to create some

natural draft to prevent the possibility of smoke or odor during appliance shut down or power failure.

This will keep exhaust from causing a nuisance or hazard from exposing people or shrubs to high

temperatures. In any case, the safest and preferred venting method is to extend the vent through the

roof vertically.

4. Distance from the bottom of the termination and grade is 12” (30 cm) minimum. This is conditional

upon the plants and nature of grade surface. The exhaust gases are hot enough to ignite grass, plants

and shrubs located in the vicinity of termination. The grade surface must not be lawn.

5. If the unit is incorrectly vented or the air to fuel mixture is out of balance, a slight discoloration of the

exterior of the house might occur. Since these factors are beyond the control of Sherwood Industries

Ltd, we grant no guarantee against such incidents.

NOTE: Venting terminals shall not be recessed into walls or siding.

Installation

VENT TERMINATION REQUIREMENTS:

IT IS RECOMMENDED THAT YOUR PELLET STOVE BE INSTALLED BY AN AUTHORIZED DEALER/INSTALLER.

Figure 5: Use in conjunction with Table 1 for allowable exterior vent termination locations.

Table 1: Use in conjunction with Figure 5 for allowable exterior vent termination locations.

Letter Minimum Clearance Description

A 24 in (61 cm) Above grass, top of plants, wood, or any other combustible materials.

B 48 in (122 cm) From beside/below any door or window that may be opened.

C 24 in (61 cm) From above any door or window that may be opened.

D 24 in (61 cm) To any adjacent building, fences and protruding parts of the structure.

E 24 in (61 cm) Below any eave or roof overhang

F 12 in (30 cm) To outside corner.

G 12 in (30 cm) To inside corner, combustible wall (vertical and horizontal terminations).

H 3 ft (91 cm) within a height of 15 ft (4.5

m) above the meter/regulator assembly

To each side of center line extended above natural gas or propane meter/regulator assembly or

mechanical vent.

I 3 ft (91 cm) From any forced air intake of other appliance

J 12 in (30 cm) Clearance to non-mechanical air supply inlet to building, or the combustion air inlet to any appliance.

K 24 in (61 cm) Clearance above roof line for vertical terminations.

L 7 ft (2.13 m) Clearance above paved sidewalk or paved driveway located on public property.

Air Supply Inlet Gas Meter Restriction Zone

(Termination not allowed)

Termination Cap

Opens

1. Do not terminate

the vent in any

enclosed or semi-

enclosed areas

such as a carport,

garage, attic,

crawlspace, narrow

walkway, closely

fenced area, under

a sundeck or porch,

or any location

that can build up

a concentration of

Installation

EXHAUST LOCATION:

83/4"

(222mm)

10 3/4"

(273mm)

Figure 6: Bern Inlet and Outlet Location.

Base of unit to center of flue 10” (273 mm)

Side of unit to center of flue 8” (222 mm)

[at center of unit]

Figure 7: Corner Installation.

CORNER THROUGH WALL INSTALLATION:

4" (8 cm)

(8 cm)

Wall thimble

manufactured

by pellet vent

manufacturer.

Installation

HORIZONTAL EXHAUST THROUGH WALL INSTALLATION:

Vent installation: install vent at clearances specified by the vent manufacturer.

A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces,

or a floor, or ceiling. Where passage through a wall or partition of combustible construction is desired,

the installation shall conform to CAN/CSA-B365 Installation Code for Solid-Fuel-Burning Appliances and

Equipment. Only use venting of L or PL type with an inside diameter of 3 or 4 inches (7.6 or 10.1 cm).

1. Choose a location for your stove that meets the requirements stated in this manual and allows

installation with the least amount of interference to house framing, plumbing, wiring, etc.

2. Install a non-combustible hearth pad

(where necessary).

3. Place the appliance 15” (37.5 cm) away

from the wall. If the stove is to be set on

a hearth pad, set the unit on it.

4. Locate the center of the exhaust pipe on

the stove. Extend that line to the wall.

Once you have located the center point on

the wall, refer to pellet vent manufacturer

installation instructions for correct hole

size and clearance to combustibles.

5. Install the wall thimble as per the

instructions written on the thimble.

Maintain an effective vapour barrier in

accordance with local building codes.

6. Install a length of 3” (75 mm) or 4” (100

mm) vent pipe into the wall thimble. The

pipe should install easily into the thimble.

7. Connect the exhaust vent pipe to the Figure 8: Straight through wall Installation.

Non-combustible

floor protection.

Existing floor

(combustible)

(15 cm)

(10 cm)

Wall

thimble

Rodent

mesh cap

45°

elbow

12"

(30.5 cm)

Exhaust Tube

3" (75mm) or 4" (100mm) "PL" or "L" vent

Wall Thimble

45° Elbow with screen or

Termination Cap

High Temperature RTV

Silicone Required

Figure 9: Venting to use with straight through wall Installation.

exhaust pipe on the stove.

Seal the connection with high

temperature silicone.

8. Push the stove straight back,

leaving a minimum of 4” (10

cm) clearance from the back

of the stove to the wall. Seal

the vent pipe to the thimble

with high temperature

silicone.

9. The pipe must extend at least

12” (30 cm) away from the

building. If necessary, bring

another length of pipe (PL

type) to the outside of the

home to connect to the

first section. Do not forget

to place high temperature

silicone around the pipe that

passes through the thimble.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Enviro Herd Handbücher

Enviro

Enviro EG28 BV Bedienungsanleitung

Enviro

Enviro C-10969 Bedienungsanleitung

Enviro

Enviro M55C-FS-2 Bedienungsanleitung

Enviro

Enviro M-55-FS Bedienungsanleitung

Enviro

Enviro MERIDIAN-2 Bedienungsanleitung

Enviro

Enviro 50-1266 Bedienungsanleitung

Enviro

Enviro C-10804 Bedienungsanleitung

Enviro

Enviro 50-1573 Bedienungsanleitung

Enviro

Enviro C-10985 Bedienungsanleitung

Enviro

Enviro M55C FS Bedienungsanleitung

Enviro

Enviro EG 28 Bedienungsanleitung

Enviro

Enviro 50-1574 Bedienungsanleitung

Enviro

Enviro Alliance EF3 Bedienungsanleitung

Enviro

Enviro M55-FS-2 Bedienungsanleitung

Enviro

Enviro 50-1220 Bedienungsanleitung

Enviro

Enviro 50-1385 Bedienungsanleitung

Enviro

Enviro EF THERMO EF THERMO 28 Bedienungsanleitung

Enviro

Enviro Meridian FS Bedienungsanleitung

Enviro

Enviro Kodiak 1200 FS Bedienungsanleitung

Enviro

Enviro EF THERMO EF THERMO 28 Bedienungsanleitung

Enviro

Enviro EF4 Bedienungsanleitung

Enviro

Enviro Westport Bedienungsanleitung

Enviro

Enviro C-10984 Bedienungsanleitung

Enviro

Enviro EF2 Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung