Envirovent FILTERLESS EXTRACT FAN SELV Series Kurzanleitung

FILTERLESS EXTRACT FAN

INSTALLATION GUIDE FOR ENGINEER / INSTALLER

SELV - IPX5

230V - IPX4

AFTER INSTALLATION THE END USER SHOULD

KEEP THIS GUIDE FOR FUTURE REFERENCE

DO NOT THROW AWAY

Filterless Extract Fan

01423 859 395

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

Safety

Read and understand these instructions before beginning

installation. The unit should be installed by a competent person.

Check there is space to ﬁt the unit in your chosen location. As

standard it can be installed using 100mm or 125mm inside diameter

duct. With the optional adaptor, a 150mm duct can also be used.

The unit can be wall mounted as standard, or ceiling, recess, inline

and window mounted using optional kits (see page 15 for further

information). The unit cannot be wall mounted upside down (with the

electronic boards at the bottom) as this will void the warranty.

Ensure the operation of the unit does not affect the operation of open-

ﬂue appliances. If you are unsure, please consult local regulations

or a qualiﬁed gas engineer. Consider the external cowl location in

relation to open-ﬂues from appliances e.g. boilers. You must ensure

the cowl is positioned a minimum distance of 300mm away in all

directions.

In kitchens, if the unit is ﬁtted above a cooker, it must be installed a

minimum distance of 1 metre above any hob, and not have a pullcord

ﬁtted.

This unit is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities or lack of experience

and knowledge, unless they have been given supervision and usage

instruction by a person responsible for their safety.

Children should be supervised to ensure they do not play with the unit.

Cleaning and user maintenance must not be performed by children.

AFTER INSTALLATION THE END USER SHOULD

KEEP THIS GUIDE FOR FUTURE REFERENCE

DO NOT

THROW AWAY

Electrical Connection

The unit must be able to be disconnected from the Mains supply

after installation. When wiring the unit to the Mains power supply,

a suitable local isolator must be incorporated in the ﬁxed wiring in

accordance with the IET Wiring Regulations.

Connection to the ﬁxed wiring must be made outside the unit in a

suitable location, following IET Wiring Regulations.

The power cable running into the cable gland must remain the

supplied ﬂexible cable (not a solid core lighting and mains cable). If

any other type of cable is forced into the cable gland, the unit will be

damaged, voiding the warranty.

If the mains cable is damaged, it must be replaced by EnviroVent, an

authorized service agent, or a similarly qualiﬁed person in order to

avoid a hazard.

Do not remove or tamper with the electronic circuit boards inside the

product. The unit requires a continuous electrical power supply and

should not be wired through a light switch.

Wiring Regulations

All wiring must comply with Building Regulations and the current

IET Wiring Regulations (BS7671 in the UK) or equivalent standards for

other countries. The ﬁnal installation should be examined and tested

by a qualiﬁed electrician.

Filterless Extract Fan

01423 859 395

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

Diagrams

Duct Adaptor

Rear Carcass

Central Cartridge

Impeller

Front Cover

195mm

129mm

174mm

78mm 99mm 56mm

99mm

248mm

AFTER INSTALLATION THE END USER SHOULD

KEEP THIS GUIDE FOR FUTURE REFERENCE

DO NOT

THROW AWAY

Wiring Diagrams

230V

SELV

220V - 240V

50/60Hz

Mains Supply

220V - 240V

50/60Hz

Mains Supply

Local

Isolator

Local

Isolator

SELV Power

Supply Connector

Block

Connect the local isolator to the Mains as part of the ﬁxed wiring.

Connect the N and L connectors of the fan power cable to the

local isolator.

The red 12V cable from the unit must be connected to the red cable

on the SELV power supply using the supplied terminal block. The

black 12V cable from the unit must be connected to the black cable

on the SELV power supply using the supplied terminal block.

+12V DC (Red)

0V DC (Black)

Filterless Extract Fan

01423 859 395

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

About the Product

Function

The EnviroVent Filterless Extract Fan has been developed to improve

indoor air quality, reduce humidity levels in kitchens and bathrooms

and resolve condensation and mould problems. It is designed to

operate continuously for up to 5 years without a major service.

Humidity Tracking

As standard, the unit is ﬁtted with Intellitrac®Technology to sense the

relative humidity in the room (not included on 2-speed variant). Once

above the setpoint, the fan speed will increase as humidity levels rise

and decrease as humidity levels fall. This intelligent function reduces

energy costs, motor wear, and ensures a long life for the product.

Pullcord

If your Filterless Extract Fan includes a pullcord, it can be used to

engage the maximum extraction rate for odour control. Pull down

on the cord to increase the unit to the maximum extraction rate. Pull

down again to decrease the unit back to the low extraction rate.

Cartridge Replacement

If necessary, the central cartridge can be exchanged for a replacement.

The removed cartridge can be returned to EnviroVent for recycling.

This allows the front cover, rear carcass and duct to remain intact

throughout the life of the property, eliminating the wasteful disposal

of non-biodegradable material to landﬁll sites.

AFTER INSTALLATION THE END USER SHOULD

KEEP THIS GUIDE FOR FUTURE REFERENCE

DO NOT

THROW AWAY

Installation

ISOLATE THE MAINS SUPPLY BEFORE BEGINNING THE INSTALLATION

1. Loosen the two screws on the bottom of the unit, leave the screws

in place and remove the front cover.

2. Pull the central cartridge out from inside the rear carcass.

3. Disconnect the green connector end of the power cable from the

unit then set the central cartridge to one side.

4. Connect the power cable and local isolator to the Mains as in the

wiring diagrams shown on page 5. Then tighten the cable gland on

the rear carcass.

1 2

Filterless Extract Fan

01423 859 395

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

5. Insert the rear carcass into the wall duct.

6. Fix to the wall using four of the labelled ﬁxing holes and the four

screws and wall plugs provided.

7. If using a backdraught shutter, insert it fully. The disc must open

towards the outside of the property.

(Do not ﬁt this if the unit is ceiling mounted).

8. Insert provided caps into the ﬁxing holes at the top of the rear

carcass (1, 2, 3).

Not using these will void the IP rating and warranty.

5 6

AFTER INSTALLATION THE END USER SHOULD

KEEP THIS GUIDE FOR FUTURE REFERENCE

DO NOT

THROW AWAY

9. Reconnect the green power connector to the unit.

10. Insert the central cartridge into the rear carcass. Do not trap any

of the cables. Fix in place using the four supplied screws.

11. To change unit settings, adjust switches 1 and 2 on the central

cartridge.

a) Default 230V duty is kitchen + humidity tracking.

b) Default SELV duty is bathroom + humidity tracking.

9 10

11b SELV11a 230V

Switch 1:

Left = Humidity Tracking

Right = Two Speed

Switch 2:

Left = Kitchen Duty

Right = Bathroom Duty

Switch 1:

Left = Humidity Tracking

Right = Two Speed

Switch 2:

Not in use.

Bathroom Duty only

L R

2PCB RELEASE

DO NOT TOUCH

L R

1 2 PCB RELEASE

DO NOT TOUCH

Filterless Extract Fan

01423 859 395

SHOULD YOU ENCOUNTER ANY PROBLEMS

INSTALLING THIS UNIT, CALL US ON:

12. Now apply the adhesive foam pad over the switches.

Not using this will void the warranty and IP rating.

13. Ensure the impeller is ﬁtted correctly, the two clips should both

be engaged.

14. Replace the front cover ensuring the pullcord sits into the slot.

Then tighten the two screws.

The unit will not operate without the front cover in place.

15. The mains supply can now be reactivated.

12 13

OFF ON

Foam Pad

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Envirovent Lüfter Handbücher

Envirovent

Envirovent cyclone 7 Bedienungsanleitung

Envirovent

Envirovent VENTY ECO2 Air Kurzanleitung

Envirovent

Envirovent energisava250 Bedienungsanleitung

Envirovent

Envirovent MEV SPIDER Bedienungsanleitung

Envirovent

Envirovent SILENT 100 Handbuch

Envirovent

Envirovent SILENT MV Series Montageanleitung

Envirovent

Envirovent CYCLONE 7 230V Series Kurzanleitung

Envirovent

Envirovent Eco dMEV+ Bedienungsanleitung

Envirovent

Envirovent POWER-170 Montageanleitung

Envirovent

Envirovent PIV AIR SOURCE Bedienungsanleitung

Envirovent

Envirovent SELV Kurzanleitung

Envirovent

Envirovent PIV Bedienungsanleitung

Envirovent

Envirovent ECO DMEV+ LC Bedienungsanleitung

Envirovent

Envirovent fliterless infinity fan 230v Kurzanleitung

Envirovent

Envirovent ATMOS WALL Bedienungsanleitung

Envirovent

Envirovent IPX4 Bedienungsanleitung

Envirovent

Envirovent MEV SPIDER Bedienungsanleitung

Envirovent

Envirovent Slimline 150 Kurzanleitung

Envirovent

Envirovent ECO dMEV LC Handbuch

Envirovent

Envirovent energiSava 300 Bedienungsanleitung

Envirovent

Envirovent MEV 160 Bedienungsanleitung

Envirovent

Envirovent ECO DMEV Bedienungsanleitung

Envirovent

Envirovent SLIMLINE 300 Kurzanleitung

Envirovent

Envirovent kudos Handbuch

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung