enware ET1400F Leitfaden
Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: +61 2 8556 4000 info@enware.com.au
I00292_Jan 20
EMERGENCY TANK SHOWER
AND EYE WASH
Assembly | Commissioning | Maintenance
INSTALLATION COMPLIANCE
Installaon of emergency showers, eye and eye/face wash equipment shall be in accordance with
AS4775 or ANSI Standard Z358.1 whichever is applicable to the installaon.
Tank Shower frame is not Cyclone Rated when mounted on FRP Grid Base. Tank Shower frame with privacy panels is Category B
Cyclone Rated when bolted to the specied concrete slab and when tank is at least half full of water.
Note: Tank shower must be installed as per manufacturer’s drawings and installaon instrucons.
ET1400F ET1400FP
ET1400FB
(with powder coang opon)
ET1400FBP
2 Call 1300 369 273 www.enware.com.au
1. Remove the tank lid.
Lid is secured with M12 bolts. Use a 19mm socket (or
equivalent) to unscrew the bolts.
2. The `oat’ has been xed in place with a carabiner onto
the eyelet loop so that it is secure during transportaon.
When removing the carabiner for assembly, please be
careful to lower the oat slowly unl oat and chain come
to a stop; if it is dropped quickly it can cause damage to
the ow controller and/or the oat (SEE IMAGE 1).
Check that the chain has not become entangled during
transportaon.
prior to installation
FLOAT
IMAGE 1
ASSEMBLING THE FRAME
The Flat Pack frame* is a frame that comes in 6 parts, and will
need to be assembled on site before commencing (SEE IMAGE 2).
The Flat Pack frame is located inside the tank for transportaon,
ready to be lied out of the tank via the slings aached to the
frames, by using a forkli or a crane.
Each frame component is secured by the xing bolts supplied.
Use 120mm long bolts for vercal xings and 70mm long bolts for
horizontal xings, with smaller M12 washers and nuts.
An-Seize is pre-applied on bolt threads. Apply more An-Seize if
required. Tighten all bolts rmly but do not over-ghten.
*Enware Tank Shower Sales Codes:
ET1400F - Tank, at pack frame
ET1400FP - Tank, at pack frame, side panels
ET1400FB - Tank, at pack frame, foot base
ET1400FBP - Tank, at pack frame, foot base, side panels
assembly
IMAGE 2
Float connected
to ow controller
by chain
www.enware.com.au Call 1300 369 273 3
ASSEMBLING RELOCATABLE FOOT BASE (ET1400FB, ET1400FBP)
1. The Foot Base is supplied as shown, with four FRP Grang
Mats, and ve Clamping Plate Sets. SEE IMAGE 3
IMAGE 4
2. Posion the Grang Mats as shown, taking note of the
orientaon of the pre-installed Mounng Plates.
SEE IMAGE 4
IMAGE 6IMAGE 5
IMAGE 3
3. Join the Grang Mats by using Clamping Plate Sets as shown.
SEE IMAGE 5 & 6
www.enware.com.au Call 1300 369 273 4
TANK INSTALLATION
4. Find the coil of eyewash hose supplied inside the tank.
Uncoil the hose and feed the hose through the top back
frame as shown (SEE IMAGE 9), with the free end loose,
ready for connecon to the tank.
Insert the other end of hose into the push-t connector on
the eyewash, and push unl it booms out.
IMAGE 9
IMAGE 8
MOUNTING PLAT E
INSTALLING ONTO GROUND SURFACE
Secure the tank shower frame onto the ground, a relocatable
foot base or concrete foong. Use appropriate xing bolts or
anchors through the Mounng Plates to x the shower frame
securely to the ground.
For installaon requiring cyclone wind category rang, see
page 7.
Important: Ensure the frame is installed on a at, level
surface.
INSTALLING ONTO GROUND WITH RELOCATABLE FOOT BASE
Place the Foot Base onto a at, level surface.
The ground surface must be well compacted and have a
maximum slope of 1% when installed on subgrade.
All four corners of the Frame have Mounng Plates to allow
the Frame to be bolted to the Foot Base.
Aach the Bolts and Washers into the corresponding
Mounng Plates already on the Foot Base, and x the Frame
onto Foot Base assembly. Use An-Seize compound on all
bolts to allow for any disassembly and relocaon of the
shower unit in future.
Install ramps up to the Foot Base on all sides, to reduce the
risk of trip hazard.
IMAGE 7
installation
5 Call 1300 369 273 www.enware.com.au
5. Check that the tank is not lled with water before installing
tank to the frame.
Li the tank onto the frame using a forkli or a crane. When
liing using a sling, use the four liing lugs located on the top
corners of the tank.
Take care to align the bolt mounng holes on the frame
with the matching threaded holes on the boom of the tank
assembly (SEE IMAGE 10).
Tank is ONLY to be lied when completely empty of water.
6. Use 80mm bolts (x10) and two larger washers (Acetyl and
stainless steel supplied) for each bolt, to x the tank in place.
Acetyl (plasc) washer should be placed closest to the frame,
so that the Acetyl washer is sandwiched between the frame
and stainless steel washer (SEE IMAGE 11).
Apply An-Seize onto bolt thread before ghtening.
Tighten bolts rmly but do not over-ghten.
7. Insert the eyewash hose into the bulk head ng, and push
unl it booms out (SEE IMAGE 12). (The ng is a push-t
connector and does not require further ghtening.)
IMAGE 10
IMAGE 11
IMAGE 12
6 Call 1300 369 273 www.enware.com.au
8. Locate the inlet ll assembly and t to the Inlet connecon of
the tank (SEE IMAGE 13).
The union connecon will have to be disassembled to screw
the top elbow in. Use appropriate thread sealing tape, to seal
the inlet connecon.
NOTE:
Inlet connecon for inlet ll assembly is noted by an arrow
directed into tank.
Overow outlet is noted by an arrow out of tank.
Assemble union connecons for inlet ll assembly, then
secure the inlet ll assembly onto tank frame using brackets
supplied. The frame has pre-drilled holes to accomodate
the 2x bracket xing screws (M6 head cap screws). Place
rubber clamps around the plasc pipe to secure the inlet ll
assembly onto bracket.
9. Reach inside boom access of tank, and pull the acvaon
valve arm down. Use appropriate step ladder to do so.
Aach shower acvaon pull handle to the acvaon valve
arm using the nut and bolt supplied (SEE IMAGE 14).
INSTALLATION IS NOW COMPLETED AND THE TANK SHOWER IS
READY TO BE COMMISSIONED.
SEE PAGE 6 FOR COMMISSIONING.
IMAGE 13
IMAGE 14
7 Call 1300 369 273 www.enware.com.au
Note: Tank Shower frame is not Cyclone Rated when
mounted on FRP Grid Base.
Tank Shower frame with privacy panels is Category B Cyclone
Rated when bolted to the specied concrete slab and when
tank is at least half full of water.
MOUNTING ANCHORS
The frame is to be anchored to the reinforced concrete
foong specied below, using the 6 mounng plates on the
frame (SEE FIGURE 1).
Each mounng plate has provision for 4 or 2 anchor bolts/rods
(NOT SUPPLIED), for a total of 20 to fully anchor the frame.
The 20 anchors must be of an M12 Stainless Steel Epoxy type
with 150mm embedment into the reinforced concrete foong
to meet Cercaon Requirements.
FOUNDATION: The foong is to be founded upon a minimum
150kPa material.
CONCRETE SPECIFICATIONS
ELEMENT SLUMP AGGREGATE
SIZE
CEMENT
TYPE F’C - MPA
FOOTING
SLAB
80mm 20mm max. GP 32
REINFORCED CONCRETE FOOTING SPECIFICATIONS
Reinforced concrete foong is to be a minimum
2000 x 2000 x 200mm (SEE FIGURE 2) with 16mm Diameter
Bars (with a Tensile Stress Capacity of 500 MPa) running at
200mm each way both top and boom (SEE FIGURE 3).
Foong must have a 50mm top and edge cover
and a 65mm boom cover.
CONCRETE NOTES
1. All workmanship and materials shall be in accordance
with AS3600-2001 concrete structures code.
2. Concrete quality and clear concrete cover are to be as
specied.
3. Concrete element sizes do not include thickness of any
applied nishes.
4. All concrete shall be mechanically vibrated. The vibrator
shall not be used to spread concrete.
5. Reinforcement is shown diagramacally, not necessarily
shown in true projecon.
6. All reinforcement shall be rmly supported on plasc
or MS plasc pped or galvanised chairs placed at not
greater than 800mm centres both ways.
cyclone wind catergory B requirements
200
2000
2000
FIGURE 2
FIGURE 1
FIGURE 3
Cross Secon showing reinforcement bars in one direcon
200
8 Call 1300 369 273 www.enware.com.au
1. Aach water source to the 40mm inlet camlock ng
(SEE IMAGE 15).
Use only clean water to ll the tank.
2. Turn on water supply and commence lling.
3. Take note of the water level indicator (SEE IMAGE 16).
When it reaches the yellow level, acvate the shower and
eye wash to ush the line and to test operaon.
When acvang the eye wash for the rst me, take the
aerators out of eye wash outlet to clear the line of any
debris.
Check for any leaks in joints and connecons.
4. Turn shower and eye wash o, and connue to ll.
Replace aerators onto the eye wash outlet.
5. Once water starts to ow out from the internal overow,
turn o the infeed water and disconnect from the 40mm
camlock ng. (SEE IMAGE 15)
COMMISSIONING COMPLETE
Shower and eyewash are now commissioned and tank shower
and eyewash are ready for use.
commissioning
IMAGE 15
IMAGE 16
FULL
EMPTY
9 Call 1300 369 273 www.enware.com.au
Descripon Part Number Image
FIXINGS-FLATPACK FRAME TO PALLET ET14SP002
10 X BOLTS
M16X80
10 X ACETAL WASHERS
10 X SS316
WASHERS M16
WATER LEVEL ASSEMBLY ET14SP003
TEMPERATURE GAUGE ET14SP004
SIGNAGE SHOWER - EYEWASH STAINLESS STEEL ET14SP005
FLOW CONTROLLER - ORIFICE PLATES ET14SP006
SHOWER ROSE ASSEMBLY ET14SP007
spare parts
10 Call 1300 369 273 www.enware.com.au
Descripon Part Number Image
PULL HANDLE ASSEMBLY ET14SP008
EYEWASH CONNECTOR KIT ET14SP009
EYEWASH OUTLET KIT ET14SP010
ASSEMBLED
FOOT BASE CLAMP KIT ET14SP011
ASSEMBLED
FOOT BASE CENTRE CLAMP KIT ET14SP012
ASSEMBLED
FOOT BASE CLAMP M10X25 SCREW - SET OF 6 ET14SP013
FOOT BASE PANEL - 1 PANEL ET14SP014
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere enware Sanitärprodukte Handbücher
enware
enware CUBISTA ENM6420 Bedienungsanleitung
enware
enware EMW803A-150 Bedienungsanleitung
enware
enware AQUABLEND ESQX ATWB C2L3 Bedienungsanleitung
enware
enware DET5071A-660B Bedienungsanleitung
enware
enware AQUABLEND SQX ATM606 Bedienungsanleitung
enware
enware AQUABLEND ESQX TOUCH FREE SERIES Montage- und Bedienungsanleitung
enware
enware aquablend 2000 Bedienungsanleitung
enware
enware LEVA Series Bedienungsanleitung
enware
enware LEVA Bedienungsanleitung
enware
enware EMD815 Bedienungsanleitung
enware
enware Wellbeing Livia LIV80WSET Bedienungsanleitung
enware
enware ET14BMSLL Bedienungsanleitung
enware
enware ENM620 Montageanleitung
enware
enware ECE030 Montageanleitung
enware
enware DET5071A-CNBSN Bedienungsanleitung
enware
enware TFC714700 Montage- und Bedienungsanleitung
enware
enware Oras Safira Bedienungsanleitung
enware
enware IFO6861 Bedienungsanleitung
