Kohler K-6228 Montageanleitung

Installation and Care Guide

Wall-Mount Kitchen Sink Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-6228

1095311-2-J

Tools and Materials

Before You Begin

CAUTION: Risk of property damage. Before ﬁnishing the

wall, make sure the supply lines are connected to the mixer

valve with the cold line plumbed on the left and the hot line

plumbed on the right.

IMPORTANT! Unless otherwise indicated, the illustrations in this

document show installation for a handle located to the right of the

spout. The valve is designed for handle installation on the right.

Special steps will need to be performed to position the handle to the

left of the valve.

NOTICE: For exterior wall installations, be sure proper wall

insulation is installed to prevent frozen pipes.

NOTE: For service parts information, visit your product page at

www.kohler.com/serviceparts.

Observe all local plumbing and building codes.

Shut off the water supply.

Carefully inspect supply tubing for any sign of damage.

The supplied plaster guard will also be used to assemble the

valve. The supplied spout tool will also be used for alignment of

the spout escutcheon.

2x4 Lumber

#10 Wood Screws

Plumbers Putty

Solder

Propane Torch

Tube Cutter

1-3/16" and 2-3/16"

Hole Saw

5/64"

3/32"

1095311-2-J 2 Kohler Co.

1. Prepare the Site

IMPORTANT! The illustration shows hole locations for a right side

handle. Reverse the holes for left side handle installation.

NOTE: The mixer valve requires special framing and support.

Construct framing for right side handle installation according to

the dimensions shown. Reverse the holes for left side handle

installation.

Verify the framing is level and will be parallel to the ﬁnished

wall. Adjust as needed.

Loosely attach the mixer valve to the framing with one or two

wood screws (not provided).

Using the ﬂat portion of the mixer valve as a guide, level the

mixer valve.

Fully tighten the wood screw(s).

16"

(406 mm)

(152 mm)

1-3/4"

(44 mm)

These

surfaces

to be flush.

1-1/2"

(38 mm)

Ø 2-3/16"

(56 mm)

Ø 1-3/16"

(30 mm)

3-1/2"

(89 mm)

Kohler Co. 3 1095311-2-J

2. Install the Supplies

CAUTION: Risk of property damage. When installing the

handle on either the right or the left side of the spout,

connect the supplies to the mixer valve with the cold supply

line plumbed on the left and the hot supply line plumbed on

the right. For left side handle installation, disregard the cold

label on the mixer valve.

IMPORTANT! The illustration shows a right side handle

installation. The supply can also be installed with the handle on the

left side.

Install 1/2″supply lines to the mixer valve with the cold supply

on the left and the hot supply on the right.

Temporarily remove and retain the plaster guard/tool and spout

plug.

Position a bucket in front of the spout shank, then turn on the

water supplies to the mixer valve.

Slowly open the valve stem. Allow hot and cold water to ﬂow

from the water supplies for approximately 1 minute to remove

any debris.

Close the valve stem. Check all connections for leaks.

Reattach the plaster guard/tool and spout plug.

Cold Supply

Plaster

Guard/Tool

Spout Plug

Mixer Valve

Hot Supply

Valve Stem

Spout

Shank

1095311-2-J 4 Kohler Co.

3. Complete the Finished Wall

IMPORTANT! The illustration shows hole locations for a right side

handle. Reverse the holes for left side handle installation.

Measure and mark the hole centers 6″(152 mm) apart from each

other.

Using a hole saw, drill a 1-3/16″(30 mm) hole for the spout and

a 2-3/16″(58 mm) hole for the handle.

Complete the ﬁnished wall.

6" (152 mm)

Ø 1-3/16"

(30 mm)

Finished Wall

Ø 2-3/16"

(56 mm)

Kohler Co. 5 1095311-2-J

4. Install the Spout

NOTE: Anchors are required when installing to materials such as

glass, mirror, and ceramic tile. The anchors and fasteners are not

supplied. Select appropriate fasteners and anchors for the ﬁnished

wall material.

If Anchors Are Required

Position the wall ﬂange over the spout plug (not shown) with the

three holes at the 2, 6, and 10 o’clock positions. Mark the hole

locations on the wall.

Drill holes at each of the marks, using the drill bit size and type

appropriate for the ﬁnished wall material.

All Installations

Conﬁrm there are three setscrews pre-installed in the wall ﬂange.

Make sure they do not protrude into the inside diameter of the

wall ﬂange. Adjust as necessary using a 3/32″hex wrench.

Apply plumbers putty or other suitable sealant to the back of the

wall ﬂange.

Slide the wall ﬂange over the spout plug (not shown).

Position the three holes on the wall ﬂange at the 2, 6, and 10

o’clock positions, then secure the ﬂange with three wood screws

or other appropriate fasteners (not provided).

Remove the spout plug.

Temporarily place the escutcheon on the wall ﬂange.

Setscrews Escutcheon

Apply sealant

to the back of

the flange.

Spout

Setscrew

Wood Screws

1095311-2-J 6 Kohler Co.

Install the Spout (cont.)

Thread the spout onto the mixer valve until the spout is fully

seated. If necessary, unthread the spout for alignment.

Slide the escutcheon away from the ﬁnished wall to access the

setscrew holes.

Using a 3/32″hex wrench, tighten the three setscrews in the wall

ﬂange until the setscrews contact the spout. Fully tighten the

setscrews.

Slide the escutcheon back against the ﬁnished wall and onto the

wall ﬂange.

With the escutcheon setscrew hole at the 6 o’clock position, use a

5/64″hex wrench to secure the escutcheon with a setscrew.

Kohler Co. 7 1095311-2-J

5. Adjust the Valve - Right Handle

CAUTION: Risk of property damage. The water supply

must be shut off before performing these steps.

CAUTION: Risk of property damage. At the maximum

valve body extension, a detent will be encountered. To avoid

leakage, do not extend the valve beyond this detent. If the

valve needs to be extended further, install deep rough-in kit

1107027. If the valve needs to be recessed further, install

shallow rough-in kit 1107026.

Shut off the water supply.

Remove the plaster guard/retaining ring tool.

Position a bucket at the spout outlet, then open the valve handle

to relieve water pressure. Leave the handle open.

Using the tool, loosen the threaded retaining ring until the valve

body disengages from the mixer valve.

Using a straight edge, adjust and hold the valve body ﬂush with

the ﬁnished wall.

NOTE: A screwdriver inserted through the holes in the plaster

guard/retaining ring tool can serve as a handle.

With the valve body ﬂush with the ﬁnished wall, retighten the

retaining ring with the tool.

Close the valve handle.

Turn on the water supply and check that the valve is functioning

properly.

Retaining Ring

Plaster Guard/

Retaining Ring Tool

1095311-2-J 8 Kohler Co.

6. Adjust the Valve - Left Handle

CAUTION: Risk of property damage. The water supply

must be shut off before performing these steps.

CAUTION: Risk of property damage. At the maximum

valve body extension, a detent will be encountered. To avoid

leakage, do not extend the valve beyond this detent. If the

valve needs to be extended further, install deep rough-in kit

1107027. If the valve needs to be recessed further, install

shallow rough-in kit 1107026.

IMPORTANT! Perform these steps when the handle will be located

on the left side of the spout.

Shut off the water supply.

Remove the plaster guard/retaining ring tool.

Position a bucket at the spout outlet, then open the valve handle

to relieve water pressure. Leave the handle open.

Using the tool, loosen the threaded retaining ring until the valve

body disengages from the mixer valve.

Retaining Ring

180˚

Plaster Guard/Tool

Valve Body

O-Rings

Spring Plunger

Kohler Co. 9 1095311-2-J

Adjust the Valve - Left Handle (cont.)

Pull out the valve body. The plaster guard/retaining ring tool can

be threaded onto the valve body to get a better grip when pulling

it out.

Rotate the valve body 180 degrees from the original position. This

allows the handle to move up when turning the water on.

Verify the o-rings on both the valve body and the mixer valve are

undamaged.

Verify the spring plunger is installed and is ﬂush with the surface

of the valve body.

Reinstall the valve body into the mixer valve until fully seated.

Using a straight edge, adjust and hold the valve body ﬂush with

the ﬁnished wall.

NOTE: A screwdriver inserted through the holes in the plaster

guard/retaining ring tool can serve as a handle.

With the valve body ﬂush with the ﬁnished wall, retighten the

retaining ring with the tool.

Close the valve handle.

Turn on the water supply and check that the valve is functioning

properly.

1095311-2-J 10 Kohler Co.

Andere Handbücher für K-6228

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler HiRise K-7337 Montageanleitung

Kohler

Kohler PINOIR K-2015 Montageanleitung

Kohler

Kohler K-T314 Bedienungsanleitung

Kohler

Kohler Revival K-2950-1 Montageanleitung

Kohler

Kohler K-2515 Montageanleitung

Kohler

Kohler K-12286-4 Montageanleitung

Kohler

Kohler Sterling SC2522SBG Montageanleitung

Kohler

Kohler K-98835T-L Bedienungsanleitung

Kohler

Kohler MODERN LIFE K-21842T Bedienungsanleitung

Kohler

Kohler K-19909 Montageanleitung

Kohler

Kohler Purist 7505D Bedienungsanleitung

Kohler

Kohler ATOM 28956X-4 Bedienungsanleitung

Kohler

Kohler K-T16236 Bedienungsanleitung

Kohler

Kohler BRAZN K-702242T Bedienungsanleitung

Kohler

Kohler K-9132 Bedienungsanleitung

Kohler

Kohler Caxton K-2216 Bedienungsanleitung

Kohler

Kohler K-7605 Bedienungsanleitung

Kohler

Kohler K-23984T-0 Bedienungsanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler K-T376 Montageanleitung

Kohler

Kohler K-13491 Montageanleitung

Kohler

Kohler Centerset K-15885 Montageanleitung

Kohler

Kohler Modernlife Touchless 77786K-TF-0 Bedienungsanleitung

Kohler

Kohler K-5805 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung