E+E Elektronik EE650 Bedienungsanleitung
GENERAL
The EE650 transmitter is designed for accurate measurement of air velocity in HVAC. It operates on the hot-film anemometer prin-
ciple and features the innovative, very robust E+E VTQ sensing element manufactured in thin-film technology combined with state-
of-the-art transfer molding.
The construction of the sensing head leads to a very low angular dependence which facilitate the installation. The mounting flange
allows for easy adjustment of the immersion depth.
The measuring range and the response time of EE650 can be selected with jumpers on the electronics board, see below
“Settings”.
EE650 is dedicated for heating, ventilation and air conditioning applications. For special applications do not hesitate to contact the
manufacturer or their local distributor.
CAUTION
• Accurate measurement results are conditioned by the correct positioning of the sensing probe in the air stream. Best accuracy
is achieved in laminar flow.
• Observe the minimum inlet and outlet path length, see page 4.
• Avoid mechanical stress onto the probe and mainly onto the sensing head.
• Observe the humidity working range 5 … 95% RH, non-condensing.
• Avoid installation in corrosive environment, as this may lead to sensor destruction.
SETTINGS
For performing EE650 settings via EE-PCS Product Configuration Software (download from www.epluse.com/configurator) the
working range jumper must be on HI.
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
t90
HI
MED
LO
I
U
Jumper t90
SLOW 4 sec.
(factory setting)
Jumper I
CURRENT
(factory setting)
no jumper
FAST 1 sec.
Jumper U
VOLTAGE
Jumper HI
0...20 m/s (0...4000 ft/min)
(factory setting)
Jumper MED
0...15 m/s (0...3000 ft/min)
Jumper LO
0...10 m/s (0...2000 ft/min)
Selection of response time t90
Selection of response time t90
Selection of output signal
Selection of ouput signal
Selection of measuring range
Selection of measuring range
EE650 - Air Velocity Transmitter for HVAC Applications
USER‘S GUIDE
CONNECTING DIAGRAM
AV
GND
V+
V / mA
1 ... V+ = supply voltage
2 ... GND = ground
3 ... AV = analogue output air velocity
Power supply
24 V AC/DC ±20% b ... brown
g ... green
y ... yellow
w ... white
s ... black
s w y g b
Remote sensor probe
TECHNICAL DATA
Measuring range
Working range 1) 0...10 m/s (0...2000 ft/min)
0...15 m/s (0...3000 ft/min)
0...20 m/s (0...4000 ft/min) (factory setting)
Output 1) 0 - 10 V -1 mA < IL< 1 mA
0...10 m/s / 0...15 m/s / 0...20 m/s 4 - 20 mA (factory setting) RL< 500 Ω(linear, 3-wires)
Accuracy at 20 °C (68 °F), 0.2...10 m/s (40...2000 ft/min) ± (0.2 m/s (40 ft/min) + 3 % of m. v.)
45 % RH, 1013 hPa 0.2...15 m/s (40...3000 ft/min) ± (0.2 m/s (40 ft/min) + 3 % of m. v.)
0.2...20 m/s (40...4000 ft/min) ± (0.2 m/s (40 ft/min) + 3 % of m. v.)
Response time τ90
1) 2) typ. 4 sec. (factory setting) or typ. 1 sec. at constant temperature
General
Power supply 24V AC/DC ± 20 %
Current consumption for AC supply max. 170 mA
for DC supply max. 70 mA
Electrical connection screw terminals max. 1.5 mm2 (AWG 16)
Cable gland M16x1.5
Electromagnetic compatibility EN61326-1 EN61326-2-3 ICES-003 ClassB
Industrial Environment FCC Part 15
Housing material Polycarbonate, UL94V-0 approved
Protection class Enclosure IP65 / NEMA 4, remote probe IP20
Temperature range working temperature probe -25 ... +50 °C (-13...122 °F)
working temperature electronic -10 ... +50 °C (14...122 °F)
storage temperature -30 ... +60 °C (-22...140 °F)
Working range humidity 5...95 % RH (non-condensing)
1) Selectable by jumper
2) Response time τ90 is measured from the beginning of a step change of air velocity to the moment of reaching 90% of the step.
DIMENSIONS MM (INCH)
6
60
Ø > 16
FOR CONDUIT
INSTALLATION
Cable gland
M16x1,5
90
~110 or 210
Ø > 13
80,6
19
101
155
15 155
46
Cable gland
M16x1,5
Type - Duct mount Mounting flange
Type - Remote sensor probe
CONFIGURATION AND ADJUSTMENT
The EE650 as ordered is ready for use immediately and requires no configuration by the user. If required, the optional E+E Product
Configuration Adapter (EE-PCA) and the E+E Product Configuration Software (EE-PCS) can be used for changing the factory
setup as well as for adjusting of the air velocity measurement. Additionally, it allows for setting the display backlighting and
orientation.
PC
HA011062
EE-PCA
V03
For product data sheets EE-PCS and EE-PCA please see www.epluse.com.
The E+E Product Configuration Software (EE-PCS) is free and can be downloaded from www.epluse.com/configurator.
MOUNTING
DRILLING IN THE WALL OF THE DUCT FOR INSTALLING THE MOUNTING FLANGE
Air flow
>16 (0.63")
60 (2.4")
The arrow engraved on the sensing head of EE650 indicates the direction of the air stream during factory adjustment. When
installing the EE650 probe, make sure that the arrow matches exactly the flow direction.
Air flow
CORRECT INCORRECT
The mounting flange allows for precise setting of the EE650 immersion depth in a duct. The entire sensing head must be in the air
flow to be measured.
Immersion depth = 30 % - 50 %
of the duct diameter
duct diameter
CORRECT INCORRECT
Air flow
POSITIONING OF AIR VELOCITY SENSOR IN A VENTILATION DUCT
The reliable and accurate measurement of air velocity depends on the correct positioning of the sensor in the ventilation duct.
Accurate measurements are only possible if the air velocity probe is positioned at a location with a laminar (to-turbulent) flow.
The required length of the calming section after a fault is a function of the tube diameter D. For a rectangular channel a x b applies:
+
<6D
<6D
>3D
>3D
>6D
>6D
>6D
Mounting the sensing probe in the middle of the
channel.
The optimal position is after the filter.
Please note sufficient distance.
Positioning the probe ahead of diffusor, at a place
with high flow rate.
Positioning the probe at a location with a laminar (to-
turbulent) flow.
Turbulent flows are caused by pipe bends, branches,
behind flaps, flans, air heaters, air coolers or cross-
sectional changes.
MAINTENANCE OF THE E+E AIR VELOCITY TRANSMITTERS
Due to the absence of moving parts, the E+E air velocity transmitters are not subject to wear. The construction (shape, dimensions
and materials) of the hot film air velocity sensor is per se highly insensitive to dust and dirt. No maintenance is required under
normal environmental conditions. For operation in polluted environment it is advisable to periodically clean the sensing head by
washing it in isopropyl alcohol, preferably in an ultrasound cleaner. Alternatively shake it gently few minutes in a pot with isopropyl
alcohol and let it dry free. Do not touch or rub the sensor and do not use any mechanical tools for cleaning.
INFORMATION +43 7235 605 0 / [email protected]
E+E Elektronik Ges.m.b.H.
Langwiesen 7 • A-4209 Engerwitzdorf
Tel: +43 7235 605-0 • Fax: +43 7235 605-8
[email protected] • www.epluse.com
LG Linz Fn 165761 t • UID-Nr. ATU44043101
Place of Jurisdiction: A-4020 Linz • DVR0962759
BA_EE650_e // v1.3 // Modifi cation rights reserved
USA
FCC notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CANADIAN
ICES-003 Issue 5:
CAN ICES-3 B / NMB-3 B
SCOPE OF SUPPLY
• EE650 Transmitter according to ordering guide
• Cable gland
• Mounting flange
• Mounting materials
• Protection cap
• Instruction manual
• Two self-adhesive labels for configuration changes (see user guide at www.epluse.com/relabeling)
• Test report according to DIN EN10204 - 2.2
ACCESSORIES
• Product configuration adapter see data sheet EE-PCA
• Product configuration software EE-PCS (free download: www.epluse.com/EE650)
• Power supply adapter V03 (see data sheet Accessories)
Inhaltsverzeichnis
Andere E+E Elektronik Sender Handbücher
E+E Elektronik
E+E Elektronik EE31 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE061 Series Gebrauchsanweisung
E+E Elektronik
E+E Elektronik EE65 Series Gebrauchsanweisung
E+E Elektronik
E+E Elektronik EE371 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE210 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE820 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE650 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE870 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE23 series Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE310 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE210 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE040 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE150 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE04 Series Gebrauchsanweisung
E+E Elektronik
E+E Elektronik EE210 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE355 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE360 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE360 Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE29 Series Bedienungsanleitung
E+E Elektronik
E+E Elektronik EE36 Series Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
