EPOX 61BXA-M Bedienungsanleitung

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 1.1

January 02, 2002

User’User’

User’ss

ManualManual

Manual

A Pentium 4 Processor based AGPA Pentium 4 Processor based AGP

A Pentium 4 Processor based AGP

(4X) mainboard (100MHz)(4X) mainboard (100MHz)

(4X) mainboard (100MHz)

SupporSuppor

Supports PC1600/2100/PC2700ts PC1600/2100/PC2700

ts PC1600/2100/PC2700ts PC1600/2100/PC2700

ts PC1600/2100/PC2700

MemorMemor

Memory Modulesy Modules

y Modulesy Modules

y Modules (DDR Memor(DDR Memor

(DDR Memor(DDR Memor

(DDR Memory)y)

y)y)

600024D11

Frequently Asked Questions For POST Port Only

The Below is the list of some basic POST Codes and their possible problems and

solutions. For more detail information about POST Codes, please refer to

Appendix E on this manual.

POST CODE Problem Solution

FFh or CFh 1.BIOS chip replace inverse

2.Update wrong BIOS

3.Mainboard problem

4.ADD-ON Card insert

inappropriate

1.Make sure BIOS chip replace

appropriate

2.Make sure all Hardware

Device insert appropriate

3.Swap mainboard

C1h – C5h

E1h – EEh

A1h – A7h

1.Memory insert inappropriate

2.Memory compability problem

3.Memory Bad

4.SPD Data incorrect

1.Make sure insert Memory

appropriate

2.Swap Memory

2Dh 1.Error occurs in VGA BIOS

2.VGA Card insert inappropriate

1.Swap VGA Card

2.Make sure insert VGA Card

appropriate

26h 1.Over clock fail 1. Clear CMOS or press insert key

to power on

07h – 12h

1.Init Keyboard Controller

2.RTC

1. Make sure insert K/B & Mouse

appropriate

2.Swap Battery

Table of Contents

Section 1 Introduction

Components Checklist..............................................1-1

Overview

Intel Pentium 4 Processors ......................................1-2

Accelerated Graphics Port .......................................1-3

Utlra ATA66/100 .......................................................1-3

Hardware Monitoring................................................ 1-4

Mainboard Form-Factor............................................1-5

I/O Shield Connector ................................................ 1-6

Power-On/Off (Remote) .......................................... 1-6

System Block Diagram ............................................. 1-7

Section 2 Features

Mainboard Features...................................................2-1

Section 3 Installation

Mainboard Detailed Layout ......................................3-2

Easy Installation Procedure

CPU Installation ........................................................3-3

Jumper Settings ......................................................... 3-5

System Memory Configuration ................................3-7

Device Connectors....................................................3-9

STR Function ............................................................. 3-13

Section 4 Award BIOS Setup

Main Menu ................................................................ 4-1

Standard CMOS Setup............................................... 4-3

Advanced BIOS Features...........................................4-7

Advanced Chipset Features .......................................4-11

Integrated Peripherals ............................................... 4-14

Page

Power Management Setup ........................................4-19

PNP/PCI Configuration Setup .................................. 4-23

PC Health Status........................................................4-25

Frequency/Voltage Control....................................... 4-27

Defaults Menu ........................................................... 4-29

Supervisor/User Password Setting ........................... 4-30

Exit Selecting ............................................................ 4-31

Section 5 Driver Installation

845 and Sound Driver Installation ............................5-1

Appendix Appendix A

Avance Media Player User’s Guide.......................... A-1

Appendix B

EEPROM BOIS Remover ......................................... B-1

Appendix C

Update Your System BIOS ........................................ C-1

Appendix D

GHOST 5.1/6.03 Quick User’s Guide (Optional) ... D-1

Appendix E

Post Codes (Optional) .............................................. E-1

Introduction

Page 1-1

Section 1

INTRODUCTION

Components Checklist

USERS

MANUAL

Package Contents

A. (1) Mainboard

B. (1) Users manual

C. (1) Floppy ribbon cable

D. (1) ATA-66 100 Hard drive ribbon

cable

E. (1) Driver and utility

Optional Item

F. (1)ATA-33 Hard drive ribbon

cable

G. (1) USB Cable

Introduction

Page 1-2

Intel Pentium 4 processors

Formally known as the Willamette, the PentiumTM 4 is the next generation IA-32

processor from Intel. This next generation design is based upon a new micro-

architecture that brings higher clock speeds and performance than previous

processors could deliver. Among other advanced features the Pentium 4 offers

Streaming SIMD extensions 2, Advanced Dynamic Execution, Hyper Pipelined

Technology, and a data transfer rate of 400MHz system bus.

Streaming SIMD Extensions 2

Building upon the foundations of core features of their previous line of proces-

sors the Pentium III, this new version introduces Streaming SIMD Extensions 2

technology commonly referred to as SSE2. But what does this mean? SIMD stands

for Single Instruction Multiple Data. Usually, processors process one data

element in one instruction, called Single Instruction Single Data, or SISD. In

contrast, with Single Instruction Single Data (SISD), SIMD has the ability to

process more than one piece of data element during one instruction.

This technology is useful for 3D graphics applications that handle considerable

amounts of floating-point numbers. With SIMD applications such as 3D graphics

will be able to processor more data per instruction when equates to better

performance. This technology adds 144 new instructions to the CPU core that can

be used in a wide variety of applications. Software programmers can for example,

take advantage of these new instructions and write more optimized code that take

advantage of newer SIMD double-precision floating-point, integer, and cache

ability instructions. In theory this will enable better next generation services such

as Interactive Digital TV to be produced.

Advanced Dynamic Execution

Advanced Dynamic Execution describes the improved implementation and

abilities over the older P6 processor lines out-of-order decoupled super scalar

execution. Dynamic execution allows instructions to the processor to be executed

without the need to do so in order. The ability to do this can add a significant

performance increase versus ordered execution.

Hyper Pipelined Technology & 00MHz System Bus

Hyper Pipelined Technology doubles the pipeline depth the Pentium 4 delivers to

20 stages. This significantly increases the performance and frequency capabilities.

Pentium 4 also introduces a 400MHz system bus as opposed to the 100 and

Introduction

Page 1-3

133MHz bus seen in previous Pentium III processors. This allows 3.2Gbytes per

second of throughput while the Pentium III had a limited 1.06Gbyte s throughput.

Willamette will reportedly be introduced in the 0.18-micron using aluminum.

For more information about all the cool new features the Pentium delivers

check out the Intel website at http://www.intel.com

Accelerated Graphics Port

(AGP or A.G.P.)

Typically, 3D graphics rendering requires a tremendous amount of memory, and

demands ever increasing throughput speed as well. As 3D products for the

personal computer become more and more popular, these demands will only

increase. This will cause a rise in costs for both end users and manufacturers.

Lowering these costs as well as improving performance is the primary motivation

behind AGP. By providing a massive increase in the bandwidth available between

the video card and the processor, it will assist in relieving some of these pressures

for quite sometime.

The board provides the AGP 2.0 interface. The AGP Interface Specification

revision 2.0 enhances the functionality of the original AGP Interface Specifica-

tion (revision 1.0) by allowing 4X data transfers (4 data samples per clock) and

1.5 volt (power supply) operation. The AGP 2.0 interface, along with SDRAM

memory technology, allows graphics controllers to access main memory at over

1GB s. In order to match the 2X and 4X AGP Card. The board used the Universal

AGP connector.

Ultra ATA/66/100

The board provides two channel Ultra ATA 66 100 Bus Master IDE controllers,

that support Ultra ATA 66 100 protocols, perfect for such demanding applications

as real-time video, multimedia, and high performance operating system. A new

IDE cable is required for Ultra ATA 66 100. This cable is an 80 conductor cable;

however the connectors are, of course, backwards compatible with ATA 33.

Introduction

Page 1-4

Hardware Monitoring

Hardware monitoring allows you to monitor various aspects of your systems

operations and status. The features include CPU temperature, voltage and RPM of

fan.

Introduction

Page 1-5

Mainboard Form-Factor

The board is designed with ATX form factor - the latest industry standard of

chassis. The ATX form factor is essentially a Baby-AT baseboard rotated 90

degrees within the chassis enclosure and a new mounting configuration for the

power supply. With these changes the processor is relocated away from the

expansion slots, allowing them all to hold full length add-in cards. ATX defines

a double height aperture to the rear of the chassis which can be used to host a

wide range of onboard I O. Only the size and position of this aperture is

defined, allowing PC manufacturers to add new I O features (e.g.; TV input, TV

output, joystick, modem, LAN, audio, etc.) to systems. This will help systems

integrators differentiate their products in the marketplace, and better meet your

needs.

 By integrating more I O down onto the board and better positioning the

hard drive and floppy connectors material cost of cables and add-in cards is

reduced.

 By reducing the number of cables and components in the system, manufac-

turing time and inventory holding costs are reduced and reliability will

increase.

 By using an optimized power supply, it's possible to reduce cooling costs

and lower acoustical noise. An ATX power supply, which has a side-

mounted fan, allows direct cooling of the processor and add-in cards

making a secondary fan or active heatsink unnecessary in most system

applications.

PCI slots

Expandable I/O

Figure 2: Summary of ATX chassis features

CPU located near

Power Supply

Single chassis fan

for system

Floppy / I E

connectors

5 1/4"

Bay

3 1/2"

Bay

AT X

Power

Supply

AGP slot

ATX power

connector

Introduction

Page 1-6

I/O Shield Connector

The board is equipped with an I O back panel. Please use the appropriate I O shield

(figure 3).

Power-On/Off (Remote)

The board has a single 20-pin connector for ATX power supplies. For ATX power

supplies that support the Remote On/Off feature, this should be connected to the

systems front panel for system Power On Off button. The systems power On Off

button should be a momentary button that is normally open.

The board has been designed with Soft Off" functions. You can turn Off the system

from one of two sources: The first is the front panel Power On Off button, and the

other is the "Soft Off" function (coming from the BOARDs onboard circuit control-

ler) that can be controlled by the operating system such as Windows® 95 98 and

Windows® 2000 to Shutdown the system.

Note: For maintaining the DDR SDRAM power during STR (ACP S3) function, it is

strongly recommend to use ATX power supplies that have a +5VSB current of

(>=) 1A (1000mA). Please check the 5VSBs specification that has been printed

on the ATX power supplys outer case.

Figure 3: I/O back panel layout

Figure 4: Simple ATX Power ON/OFF Controller

MIC

parallel port Joystick/Midi port

USB port

COM1 COM2 Speaker

Line_in

PS/2 Mouse

PS/2

K YBOARD

ATX POW R SUPPLY

20-pin

Case (chassis) Power ON/OFF button

Inhaltsverzeichnis

Andere EPOX Hauptplatine Handbücher

EPOX

EPOX EP-4PEAE 11 Bedienungsanleitung

EPOX

EPOX MU-4PEA800 Bedienungsanleitung

EPOX

EPOX MVP4F Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

EPOX

EPOX EP-4B2AE Bedienungsanleitung

EPOX

EPOX EP-8KTA Bedienungsanleitung

EPOX

EPOX IP-4PCI2E Series Bedienungsanleitung

EPOX

EPOX ProNiX EP-9NPAJ Bedienungsanleitung

EPOX

EPOX V370A Bedienungsanleitung

EPOX

EPOX LXR Bedienungsanleitung

EPOX

EPOX EP-3VCA Bedienungsanleitung

EPOX

EPOX P2-133A Bedienungsanleitung

EPOX

EPOX 8U1697 GLI Bedienungsanleitung

EPOX

EPOX EP-6CXA2C Bedienungsanleitung

EPOX

EPOX EP-MVP3C Bedienungsanleitung

EPOX

EPOX EP-MVP3G-M Bedienungsanleitung

EPOX

EPOX EP-7KXA Bedienungsanleitung

EPOX

EPOX EP-6ZXM Bedienungsanleitung

EPOX

EPOX EP-61BXC-A Bedienungsanleitung

EPOX

EPOX EP-3WEF2 Bedienungsanleitung

EPOX

EPOX EP-MVP4G Bedienungsanleitung

EPOX

EPOX KP6-LA Bedienungsanleitung

EPOX

EPOX EP-8kem Bedienungsanleitung

EPOX

EPOX MVP4A Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

Epson

Epson S5U13700P00C000 Bedienungsanleitung