EPOX P2-133A Bedienungsanleitung

TRADEMARK

All products and company names are trademarks or

registered trademarks of their respective holders.

These specifications are subject to change without

notice.

Manual Revision 1.0

November 25, 1998

P2-133AP2-133A

P2-133A

A PentiumA Pentium

A Pentium®®

®®

®II or DeschutesII or Deschutes

II or DeschutesII or Deschutes

II or Deschutes

Slot1 Processor based AGPSlot1 Processor based AGP

Slot1 Processor based AGP

motherboard (100/66MHz)

FeaturesP2-133A

Page 1

FEATURES

P2-133A Features:

•P2-133A is based on the Pentium®II or Deschutes Processor operating at 233

~ 333MHz (66MHz) or 300 ~ 450MHz (100MHz) on Slot 1. The board is

configured by an Easy-Setting-Dual-Jumper (E.S.D.J.) to match your CPU

clock speed.

•Designed with VIA APOLLO PRO+ 693/596A AGPset.

•Supports up to 384 Mega of DRAM (minimum of 16 MB) on board, You can

use 168-pin DIMM x 3. It will automatically detect Extended Data Output

(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM) at

66MHz or 100MHz (please see Section 3-2).

•P2-133A will support Error Checking and Correcting (ECC) when using

paritys DRAM memory modules. This will detect multiple bit errors and

correct 1-bit memory errors.

•Supports (2) 16 bit ISA slots, (5) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The P2-133A supports (5) PCI

Bus Master slots and a jumperless PCI INT# control scheme which reduces

configuration confusion when plugging in PCI card(s).

•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary IDE

interfaces.

•Designed with Winbond W83977TF Multi I/O: (1) floppy port, (1) parallel port

(EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

•Includes a PS/2 mouse connector.

•Allows use of a PS/2 keyboard.

•Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com

please visit our Technical Support section for the latest updates)

FeaturesP2-133A

Page 2

•P2-133A utilizes a Lithium battery which provides environmental protection

and longer battery life.

•Supports the Universal Serial Bus (USB) connector. The VIA 82C596A chip

provides the means for connecting PC peripherals such as; keyboards,

joysticks, telephones, and modems.

•Built-in ATX 20-pin power supply connector.

•Software power-down when using Windows®95/98.

•Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely.

•Resume by Alarm - Allows your system to turn on at a preselected time.

•Power Loss Recovery - In the event of a power outage your system will

automatically turn itself back on without user intervention.

•Supports CPU Hardware sleep and SMM (System Management Mode).

•Supports Desktop Management Interface (DMI) facilitating the management

of desktop computers, hardware and software components and peripherals,

whether they are stand-alone systems or linked into networks. (optional)

•Supports Hot key, Any key or password Keyboard power ON function

(KBPO).

•Supports USDM software to offer motherboard various status on Windows®

95/98, or Windows®NT 4.0/5.0.

•Supports the CPU, PWR and Chassis fan Auto stop in sleep mode.

•Supports the System Power LED (PANEL) blinks in the sleep mode.

•Built-in WOL (Wake On LAN)Connector.

• Built-in SB-LINK Header for Creative Blaster®AWE64D PCI Bus Sound

Card.

Installation P2-133A

Page 3

Figure 1

P2-133A Detailed Layout

AGP SLOT

PCI Slot #1

PCI Slot #2

ISA Slot #1

ISA Slot #2

Battery

ATX Power Input

Winbond

83977

I/Oset

USB 1

(Top)

Mouse

(Top)

USB 0

(Bottom)

Keyboard

(Bottom)

IDE2

Secondary IDE

IDE1

FDD1

CPU Cartridge SLOT 1

J7:WOL

DIMM 2

DIMM 1 Bank 0

Bank 1

DIMM 3 Bank 2

Flash Memory

for BIOS

PCI Slot #3

PCI Slot #4

PCI Slot #5

COM 1COM 2COM 2

USB

PS/2

ESDJ

JP3

124MHz

112MHz

103MHz

100MHz

66MHz

AUTO

5.5X

4.5X

3.5X

1 2

25 26

133MHz

Parallel Port

SB_Link

CHASSIS FAN

POWER

FAN

JP13

JP1

POWER_ON

IR CONN.

RESET

SPK

KEYLOCK

CPU FAN

InstallationP2-133A

Page 4

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure Jumpers to match your hardware

Install memory chips

Device Connectors

Configure Jumpers

We design this motherboards with an ESDJ to make your installation fast and easy.

The following will describe all of the ESDJ that you are required to set before moving

on to step 2.

Note: The ESDJ as depicted as shown (Figure 1) in their correct physical

orientation.

JP13 Keyboard Power-ON function (refer the section 3-5)

JP13 = 1-2 - Enabled

= 2-3 - Disabled(Default)

J7 WOL (Wakup On Lan) Connector

Reserved for NIC (Network Interface Card) to

Wake the System.

JP1 = 1-2 - Run Mode (Default)

= 2-3 - Clear CM OS (momentarily)

JP1 CMOS Clear

J8 SB-LINK Header

Reserved for Creative SB-LINK (Sound Blaster

LINK ) with the Sound Blaster AWE64D PCI

Sound Card to Compatible DOS games and

Multimedia applications.

InstallationP2-133A

Page 5

Note: Based on the implementation of VIA Chipset Apollo Pro+, P2-133A is able

to provide two host bus frequencies -- either 66 or 100MHz for Slot1 processor

and memory operating. The default is set at 100MHz once Pentium®II processor

to be mounted onto this motherboard. However, no matter what kind of Slot1

processoryouinstalled,itshouldcomewithrightmemorymodulesfornormaland

stableoperation. For example, if you install aDeschutes processor, you should use

the SDRAM module with 100MHz based(or above) to match the CPU speed.

Furthermore,onething youmay needtobear inmind,before theCPU installation,it

is anyway our advice to use JP3 and set up right speed of Slot1 processor at any

time.

InstallationP2-133A

Page 6

System Memory Configuration

Memory Layout

The P2-133A supports (3) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized

DRAM). The DIMMs may be installed using just one chip.

•We recommend using SDRAM DIMM can not mixing

with EDO DIMM modules.

• The EDO DIMM only support pentium®II Processor at 66MHz, not

support Deschutes Processor at 100MHz.

• We recommend when installed the 100MHz Deschutes Processor

using DIMM SDRAM must be 125MHz (-8ns) bus speed. If used

100MHz (-10ns) SDRAM may be critical timing for the

motherboard.

• About the “PC/100 SDRAM spec.” information you may visit Intel’s

home page at:

http//developer.intel.com/design/pcisets/memory/index.htm

• DIMM SDRAM may be 83MHz (-12ns), 100MHz (-10ns) or

125MHz (-8ns) bus speed.

Figure 2 and Table 1 show several possible memory configurations using

DIMM 1 (M1)

DIMM 2 (M2)

DIMM 3 (M3)

Bank 0

Bank 1

Bank 2

-Synchronous

-SDRAM or EDO

DIMM

Figure 2

Installation P2-133A

Page 7

yromeMlatoT 1MMID )0knaB( 2MMID )1knaB( 3MMID )2knaB(

BM483= mumixaM

*MARDS/ODE ,BM23,BM61,BM8 1XBM821,BM46

BM652= mumixaM

*MARDS/ODE ,BM23,BM61,BM8 1XBM821,BM46

*MARDS/ODE ,BM23,BM61,BM8 1XBM821,BM46 enoN

BM821= mumixaM

*MARDS/ODE ,BM23,BM61,BM8 1XBM821,BM46 enoNenoN

Installation P2-133A

Page 8

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connections

(figure 12).

USB 1

(Top)

USB 0

(Bottom)

PS/2 Mouse

(Top)

PS/2 Keyboard

(Bottom)

Parallel Port

(Top)

Com1 Com2

(Bottom Left) (Bottom

Right)

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J5: Power Supply Fan Monitoring

• A plug-in for the Power supply so that BIOS can monitor the RPM’s

J6: Chassis Fan Power

• A plug-in for the chassis Fan Power

J7: WOL (Wake On Lan) Connector

J8: SB-LINK Connector

• 5-PIN Header for Creative Blaster® AWE64D PCI Sound Card.

PW2: ATX Power Connector

• 20-pin power connector

J2,J3:Chassis Panel Connector

• Keylock, Speaker, Reset, Sleep, Turbo LED and HDD LED

IDE1:Primary IDE Connector

IDE2:Secondary IDE Connector

FDD1:Floppy Controller Connector

Figure 12

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345

InstallationP2-133A

Page 9

Power On/Off - This is connected to the power button on the case.

Using the Soft-Off by Pwr-BTTN feature, you can choose either

Instant Off (turns system off immediately), or 4 sec delay (you need to

hold the button down for 4 seconds before the system turns off). When

the system is in 4 sec delay mode, we has added a special feature to

make the system go into suspend mode when the button is pressed

momentarily.

Device Connectors (continued)

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is

activate

KeyLock - Keyboard lock switch & Power LED connector

1. Power LED(+) 4. Keylock

2. N/C 5. GND

3. GND

J3 1

* The power LED lights when the

system is powered on and blinks in

SLEEP MODE (Suspend mode).

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

Andere Handbücher für P2-133A

Inhaltsverzeichnis

Andere EPOX Hauptplatine Handbücher

EPOX

EPOX BX3 Bedienungsanleitung

EPOX

EPOX EP-5BTXA-E Bedienungsanleitung

EPOX

EPOX EP-6VBA Bedienungsanleitung

EPOX

EPOX 6WEA4I Bedienungsanleitung

EPOX

EPOX EP-3VHA Bedienungsanleitung

EPOX

EPOX MVP4G Bedienungsanleitung

EPOX

EPOX nForce2 Ultra 400 Bedienungsanleitung

EPOX

EPOX EP-3VBA Bedienungsanleitung

EPOX

EPOX V370A Bedienungsanleitung

EPOX

EPOX EP-BX5 Bedienungsanleitung

EPOX

EPOX EP-8HDA5J Bedienungsanleitung

EPOX

EPOX EP-3VWM Bedienungsanleitung

EPOX

EPOX EP-BX6 Bedienungsanleitung

EPOX

EPOX P55-KV Bedienungsanleitung

EPOX

EPOX PP6-NF Bedienungsanleitung

EPOX

EPOX BX6 Bedienungsanleitung

EPOX

EPOX EP-6CXA2C Bedienungsanleitung

EPOX

EPOX EP-8kem Bedienungsanleitung

EPOX

EPOX EP-6ZXM Bedienungsanleitung

EPOX

EPOX 6XBA2 Bedienungsanleitung

EPOX

EPOX P55TV2 Bedienungsanleitung

EPOX

EPOX 9npa Bedienungsanleitung

EPOX

EPOX 3WXM4 Bedienungsanleitung

EPOX

EPOX kl-133m Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

Epson

Epson S5U13700P00C000 Bedienungsanleitung