Epson Endeavor P60 Bedienungsanleitung

EPSON

User’s Guide

Printed on 50% recycled paper, 10% post-consumer content

IMPORTANT NOTICE

DISCLAIMER OF WARRANTY

Epson America makes no representations or warranties, either express or implied, by or

with respect to anything in this manual, and shall not be liable for any implied warranties

ofmerchantability and fitness for a particular purpose or for any indirect, special, or

consequential damages. Some states do not allow the exclusion of incidental or

consequential damages, so this exclusion may not apply to you.

system, or transmitted, in any form or by any means, electronic, mechanical,

photocopying, recording, or otherwise, without the prior written permission of Epson

America, Inc. No patent liability is assumed with respect to the use of information

contained herein. Nor is any liability assumed for damages resulting from the use of the

information contained herein. Further, this publication and features described herein are

subject to change without notice.

TRADEMARKS

EPSON is a registered trademark of Seiko Epson Corporation

EPSON Connection and EPSON Direct are service marks of Epson America, Inc.

General notice: Other product names used herein are for identification purposes only and

may be trademarks of their respective owners. EPSON disclaims any and all rights in

those marks.

Torrance, California, USA 2/94

Important Safety Instructions

Read all of these instructions and save them for later reference. Follow

all warnings and instructions marked on the computer.

Unplug the computer before cleaning. Clean with a damp cloth only.

Do not spill liquid on the computer.

Do not place the computer on an unstable surface or near a radiator

or heat register.

Do not block or cover the openings in the computer’s cabinet. Do not

insert objects through the slots.

Use only the type of power source indicated on the computer’s label.

Connect all equipment to properly grounded power outlets. Avoid

using outlets on the same circuit as photocopiers or air control

systems that regularly switch on and off.

Do not let the computer’s power cord become damaged or frayed.

If you use an extension cord with the computer, make sure the total

ampere rating of the devices plugged into the extension cord does

not exceed the cord’s ampere rating. Also, make sure the total of all

devices plugged into the wall outlet does not exceed 15 amperes.

Except as specifically explained in this User’s Guide, do not attempt

to service the computer yourself.

Unplug the computer and refer servicing to qualified service

personnel under the following conditions:

If the power cord or plug is damaged; if liquid has entered the

computer; if the computer has been dropped or the cabinet damaged;

if the computer does not operate normally or exhibits a distinct

change in performance. Adjust only those controls that are covered

by the operating instructions.

If you plan to use the computer in Germany, observe the following:

To provide adequate short-circuit protection and over-current

protection for this computer, the building installation must be

protected by a 16 Amp circuit breaker.

Beim AnschluB des Computers an die Netzversorgung muB

sichergestellt werden, daB die Gebäudeinstallation mit einem

16 A Überstromschutzschalter abgesichert ist.

iii

Importantes instructions de sécurité

Lire attentivement les instructions suivantes et les conserver pour les

consulter en cas de besoin. Observer soigneusement tous les

avertissements et directives marques sur l’ordinateur.

lDebrancher l’ordinateur avant de le nettoyer. N’utiliser qu’un chiffon

humide. Veiller a ne pas renverser de liquides sur l’appareil.

lNe pas placer l’ordinateur sur une surface instable ni pres d'une

source de chaleur.

lNe pas bloquer ni couvrir les orifices d’aération de l’appareil. Ne pas

introduire d’objets dans les ouvertures.

lUtiliser seulement le type de source d’alimentation électrique indiqué

sur l’etiquette.

lTout l’equipement doit être branche sur des prises de courant avec

contact de terre. Ne jamais utiliser une prise sur le même circuit

qu’un appareil a photocopies ou un systéme de controle de

ventilation avec commutation marche-arrêt automatique.

lS’assurer que le cordon d’alimentation de l’ordinateur n’est pas

abîme ni effiloché.

lDans le cas ou on utilise un cordon de rallonge avec l’ordinateur,

s’assurer que l’intensite en amperes requise pour tous les appareils

branches sur ce cordon ne soit pas superieure a la capacite du cordon.

S’assurer aussi que cette intenste ne depasse jamais la somme de 15

amperes pour l’ensemble des appareils.

lSauf dans les cas specifiques expliques dans ce manuel de l’usager,

ne pas essayer d’entretenir ou de reparer l’ordinateur soi-même.

lDebrancher l’ordinateur et contacter un technicien qualifie dans les

circonstances suivantes:

Si le cordon ou la prise sont abimes; si un liquide a pénétré a

l’intérieur de l’appareil; si on a laissé tomber l’appareil ou si le boîtier

est endommagé; si l’ordinateur ne fonctionne pas normalement ou

fonctionne dune manière très différente de l’ordinaire. N’ajuster que

les commandes décrites dans les directives.

lPour utiliser l’ordinateur en Allemagne, il est nécessaire que le

bâtiment soit muni d’un disjoncteur de 16 amperes pour proteger

l’ordinateur contre les courts-circuits et le survoltage.

Contents

lntroduction

Central Processing Unit (CPU)

System Memory

Cache Memory

Video

Mass Storage

System BIOS

PCI Auto-configuration

BIOS Upgrades

How to Use This Manual

Conventions Used in This Manual

Where to Get Help

Compu Serve On-line Support

Chapter 1 Seting Up Your System

Choosing a Location ........................ l-l

Setting the Input Voltage ...................... l-2

Checking the Power Cord ..................... l-3

Installing Optional Devices .................... l-4

Front Panel Features ........................ l-5

Back Panel Features ......................... l-6

Turning On the System ....................... l-6

Turning Off the System .......................

1-8

Chapter 2 Running the Setup Program

Starting the Setup Program

2-2

Setup Options

2-4

Standard CMOS Setup

2-5

Date

2-5

Time

2-5

Floppy Drive A:

2-5

Floppy Drive B:

2-5

DriveC,D,E,F:Type. .........................

Drive C, D, E, F: Timeout .........................

Keyboard .........................

Base Memory .........................

Extended Memory .........................

Advanced CMOS Setup .........................

Typematic Rate Programming .........................

Press Fl Message Display .........................

System Boot Up Num Lock .........................

System Boot Up Sequence .........................

System Boot Up CPU Speed .........................

Cache Memory .........................

Network Password Checking .........................

ISA Linear Frame Buffer .........................

Set Linear Frame Address To .........................

Disable Shadow Memory Size .........................

Disable Shadow Memory Base .........................

Base Memory Size .........................

IDE DMA Transfer Mode ................................

IDE Multiple Sector Mode .........................

Enhanced ISA LBA Translators .........................

Enhanced ISA Timing .........................

ISA IRQ 9, ISA IRQ 10, and ISA IRQ 11 ................

Peripheral Management Setup .........................

Programming Option .........................

On-board Floppy Drive .........................

On-board IDE Drive .........................

First Serial Port Address .........................

Second Serial Port Address .........................

Parallel Port Address .........................

IRQ Active State .........................

Parallel Port Mode .........................

Configure With BIOS Defaults .........................

Configure With Power-on Defaults ..................

Change Password .........................

Write to CMOS and Exit .........................

Do Not Write to CMOS and Exit .........................

2-5

2-6

2-7

2-8

2-9

2-10

2-l1

2-12

2-13

2-14

Chapter 3

Using Your Computer

Stopping a Command or Program......................... 3-l

Resetting the Computer .........................3-2

Using a Password .........................

3-3

Changing the Processor Speed .........................

3-3

Upgrading the BIOS .........................

3-5

Recovering an Interrupted BIOS Upgrade 3-7

Chapter 4

Installing and Removing Options

Removing the Computer’s Cover.........................

4-2

Replacing the Computer’s Cover .........................

4-3

Main System Board Map...............................

4-4

Main System Board Jumpers.........................

4-5

Installing an Expansion Board.........................

4-6

Removing an Expansion Board.........................

4-9

Installing SIMMs......................... 4-10

Removing SIMMs ......................... 4-14

Installing VRAM.........................

4-15

Removing VRAM ......................... 4-17

Post-installation Setup ......................... 4-17

Chapter 5

Installing and Removing Dives

Setting the Hard Disk Drive Jumpers.........................

5-2

Removing the Drive’s Mounting Frames .........................

5-3

Removing the 3.5-inch Drive Carrier .........................

5-4

Installing the 3.5-inch Drive Carrier .........................

5-6

Installing a 3.5-inch Drive .........................

5-7

Removing a 3.5-inch Drive .........................

5-8

Installing a 5.25-inch Drive .........................

5-9

Removing a 5.25-inch Drive

.........................

5-13

vii

Chapter 6

Using the video Utilities

Supported Video Refresh Rates

Supported Video Modes

Monitor List

Before You Run the Mach32 Installation Program

Starting the Mach32 Installation Program

Setting the Power-Up Configuration

Running the Graphics Adapter Diagnostics

Installing the Video Adapter Utilities

Installing the Windows Device Drivers

Using FlexDesk

Installing the Adapter Interface

Chapter 7

Troubleshooting

6-2

6-4

6-6

6-7

6-8

6-l1

6-12

6-13

6-18

Identifying Your System .........................

Error and Information Messages .........................

Beep Codes. .........................

Error Messages .........................

ISA NM1 Messages ............................

General Troubleshooting ..............................

Problems at Initial System Start-up .......................

Problems When the System was Running Correctly

Problems Running New Application Software

Miscellaneous Problems .........................

Appendix A Specifications

7-l

7-3

7-4

7-6

7-8

7-9

7-10

7-12

CPU and Memory ...........................A-l

Controllers ...............................A-3

Interfaces ................................ A-4

Mass Storage .............................. A-4

Keyboard ................................ A-5

Setup Program ............................. A-5

Physical Characteristics ........................A-5

Power Supply .............................A-5

Environmental Requirements .................... A-7

Tested Operating Environments .................. A-7

Viii

Safety Compliance ....................A-12

Options Available from EPSON....................A-8

System Memory Map....................A-9

System I/O Addresses....................A-10

System Board Interrupts....................A-11

DMA Channels....................A-12

Connector Pin Assignments

....................A-13

Index

Introduction

Your EPSON@ computer represents the state-of-the-art in PC

technology by incorporating the high-performance Intel@

PentiumTM microprocessor and PC1 bus architecture. Your

system includes the following features:

A 60 MHz Intel Pentium microprocessor

8MB of random access memory (RAM) on two 4MB single

in-line memory modules (SIMMs), expandable up to 128MB

256KB of secondary cache memory on the system board

Integrated AT1 Mach32 high-performance, local bus PC1

graphics controller with a 15-pin analog VGA port

1MB of video RAM (VRAM) expandable to 2MB using

eight 256KB VRAM modules

Two PC1 expansion slots (for one full-length board and one

half-length board)

Three 16-bit, ISA expansion slots (for one full-length board

and two half-length boards)

Super I/O controller integrating the serial ports, the

parallel port, the diskette drive, and the IDE hard disk

drive controller functions into a single chip

IDE ISA hard disk drive interface

Diskette drive controller supporting 2.88MB drives and

providing auto-sensing capabilities

System BIOS in a flash EEPROM including support for the

Setup program and PC1 adapter auto-configuration utility

Introduction 1

Andere Handbücher für Endeavor P60

Inhaltsverzeichnis

Andere Epson Desktop Handbücher

Epson

Epson ActionTower 2000 Bedienungsanleitung

Epson

Epson EISA Desktop Abmessungen

Epson

Epson Proper Method for Running Benchmark and Diagnostics... Abmessungen

Epson

Epson Equity 386/20 Abmessungen

Epson

Epson EL 486UC+ Bedienungsanleitung

Epson

Epson Endeavor L Bedienungsanleitung

Epson

Epson ExpressStation Bedienungsanleitung

Epson

Epson ActionDesk 4000 Abmessungen

Epson

Epson CW3S16 Canadian Product Bedienungsanleitung

Epson

Epson Endeavor VL Bedienungsanleitung

Epson

Epson ActionPC 2600 Installations- und Betriebshandbuch

Epson

Epson Equity 386SX/20 PLUS Bedienungsanleitung

Epson

Epson ActionTower 3000 Computer Bedienungsanleitung

Epson

Epson EQUITY II+ Abmessungen

Epson

Epson Express Station Express Station Bedienungsanleitung

Epson

Epson Equity 386/33 PLUS Installations- und Betriebshandbuch

Epson

Epson Progression 4 Bedienungsanleitung

Epson

Epson Powerspan Installations- und Betriebshandbuch

Epson

Epson Equity 386SX PLUS Bedienungsanleitung

Epson

Epson ActionDesk 4000 Bedienungsanleitung

Epson

Epson ActionDesk 4000 Bedienungsanleitung

Epson

Epson ActionTower 7500 Bedienungsanleitung

Epson

Epson ActionPC 2600 Bedienungsanleitung

Epson

Epson Apex 100 Abmessungen

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung