Epson S1D13C00 Bedienungsanleitung
Rev. 1.0
S1D13C00
S5U13C00P01C100 Customer
Development Board User
Manual
Document Number: XB8A-G-001-01.0
Evaluation board/kit and Development tool important notice
1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration,
or development purposes only. Do not use it for other purposes. It is not intended to meet the requirements of
design for finished products.
2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a
consumer product. The user should use it properly and in a safe manner. Seiko Epson dose not assume any
responsibility or liability of any kind of damage and/or fire coursed by the use of it. The user should cease to
use it when any abnormal issue occurs even during proper and safe use.
3. The part used for this evaluation board/kit or development tool may be changed without any notice.
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written
permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice.
Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material
or due to its application or use in any product or circuit and, further, there is no representation that this material is
applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any
intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that
anything made in accordance with this material will be free from any patent or copyright infringement of a third
party. When exporting the products or technology described in this material, you should comply with the
applicable export control laws and regulations and follow the procedures required by such laws and regulations.
You are requested not to use, to resell, to export and/or to otherwise dispose of the products (and any technical
information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other
military purposes.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective
companies.
©SEIKO EPSON CORPORATION 2018-2019. All rights reserved.
S5U13C00P01C100 Board User Manual Seiko Epson Corporation i
(Rev. 1.0)
Table of Contents
1. Introduction ................................................................................................................ 3
2. Connecting the ET011TT2 EPD Panel ...................................................................... 5
3. Connecting to the Host MCU Board ......................................................................... 6
3.1 EK-TM4C1294XL Board .............................................................................................................6
3.2 Nucleo-F746ZG or Nucleo-F767ZI Board .................................................................................7
4. Jumpers Settings....................................................................................................... 8
5. Push-Buttons and EPD Panel Connectors .............................................................. 9
5.1 Push-Buttons ..............................................................................................................................9
5.2 Header for Hulk Power Board Connection (CN1) .................................................................10
5.3 FPC Connector for ET011TT2 Connection (CN2)..................................................................11
6. Pre-installed On-board Components ..................................................................... 12
6.1 16Mbytes QSPI Serial Flash (U2) ............................................................................................12
7. Host MCU Board Connections................................................................................ 13
7.1 Tiva C Series EK-TM4C1294XL Launchpad...........................................................................13
7.2 STM32 Nucleo-144 development board .................................................................................15
8. Parts List................................................................................................................... 17
9. S5U13C00P01C100 Schematics.............................................................................. 18
10. Revision History....................................................................................................... 20
ii Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
Introduction
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 3
(Rev. 1.0)
1. Introduction
The S5U13C00P01C100 is the S1D13C00 EPD Evaluation Board. It is a BoosterPack board with a connector
for the E Ink ET011TT2 EPD panel intended to be directly connected to the TI Tiva C Series EK-TM4C1294XL
Launchpad evaluation board for evaluating and developing embedded EPD applications using the Epson
S1D13C00 Memory Display Controller IC. It is possible to be controlled by the ST Nucleo-F746ZG or Nucleo-
F767ZI board through the S5U13C00M00C100 (STM32 Nucleo-144 development board) board.
Figure 1 shows the S5U13C00P01C100 EPD Evaluation Board.
Figure 1 – S5U13C00P01C100 EPD Evaluation Board
The S5U13C00P01C100 EPD Evaluation Board consists of:
A S1D13C00 Memory Display Controller (U1)
Four 2x10 connectors for Host Interface connection (J4, J5, J6 and J7) and +5V/+3.3V power
A 16Mbytes QSPI Serial Flash (U2)
A flexible printed circuit (FPC) connector (CN2) for connecting to a ET011TT2 EPD panel
An 18-pin right-angle header connector for connecting to other panels
Figure 1.1 shows the block diagram of S5U13C00P01C100, focused on interfaces. It has a host MCU interface
and three interfaces for displays. CN1 is an interface for E Ink’s HULK power board, CN2 is an interface for the
ET011TT2 panel module, and there are through holes for interface to a memory display panel. You can select
one of these interfaces to connect a panel module. CN2 interface is also possible to connect other E Ink panel
modules. The booster components on the S5U13C00P01C100 are similar circuits to HULK power board
suitable for the ET011TT2 panel module.
Introduction
4Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
Figure 1.1 – S5U13C00P01C100 Block Diagram for Interface
Regulator
Host
interface
Memory display interface
HULK power board interface
ET011TT2
panel module
interface
S1D13C00
Serial
Flash
Through holes
Booster
Components *
CN1
C
N
2
*Booster components are part of booster circuits of ET011TT2 panel module.
Connecting the ET011TT2 EPD Panel
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 5
(Rev. 1.0)
2. Connecting the ET011TT2 EPD Panel
Figure 2 – Connecting the ET011TT2 EPD Panel
Figure 2.1 – Connecting the HULK Power Board with ET011TT2 EPD Panel
Connecting to the Host MCU Board
6Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
3. Connecting to the Host MCU Board
3.1 EK-TM4C1294XL Board
Position the S5U13C00P01C100 EPD Evaluation Board on TOP of the EK-TM4C1294XL Launchpad Board,
press the two boards together with J4 connecting to X8, J5 connecting to X9, J6 connecting to X6, and J7
connecting to X7 respectively.
Figure 3 – Connecting the S5U13C00P01C100 to the EK-TM4C1294XL
J4
J5
J6
J7
X8
X9
X6
X7
Connecting to the Host MCU Board
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 7
(Rev. 1.0)
3.2 Nucleo-F746ZG or Nucleo-F767ZI Board
First, connect the S5U13C00M00C100 adapter board to the Nucleo board. Second, connect the
S5U13C00P01C100 board to the S5U13C00M00C100 adapter board.
Figure 3.1 – Connecting the S5U13C00P01C100 to the Nucleo-F746ZG or Nucleo-F767ZI
Jumpers Settings
8Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
4. Jumpers Settings
The following tables show the jumpers settings for the S5U13C00P01C100 EPD Evaluation Board.
Figure 4 – S5U13C00P01C100 Jumpers Locations
Jumpers
Descriptions
Type
Default Position
JP2
External VC3 Connection
2-pin
Not installed
JP3
VDD_IC supply series jumper
2-pin
Installed
JP4
VDD_EPD supply series jumper
2-pin
Installed
JP6
DISPVDD source supply
1-2 = VDD_EPD
2-3 = VMDL
3-pin
1-2 (VDD_EPD)
JP7
HIFCNF (host interface configuration)
1-2 = SPI/QSPI
2-3 = INDIRECT 8-BIT (not used)
3-pin
1-2 (SPI/QSPI)
JP2
JP3
JP4
JP6
JP7
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Epson Hauptplatine Handbücher
Epson
Epson S1R72U16 Bedienungsanleitung
Epson
Epson S1D13743 Bedienungsanleitung
Epson
Epson S5U13515P00C100 Bedienungsanleitung
Epson
Epson S5U1C31D50T1 Bedienungsanleitung
Epson
Epson S5U13A05P00C100 Bedienungsanleitung
Epson
Epson S5U13705B00C Bedienungsanleitung
Epson
Epson S5U13781R00C100 Bedienungsanleitung
Epson
Epson S5U13513P00C100 Bedienungsanleitung
Epson
Epson S1S65010 Bedienungsanleitung
Epson
Epson S5U13L01P00C100 Bedienungsanleitung
Epson
Epson S5U13709P00C100 Bedienungsanleitung
Epson
Epson S5U13706P00C100 Bedienungsanleitung
Epson
Epson S5U13781R01C100 Bedienungsanleitung
Epson
Epson S1R72V27 Bedienungsanleitung
Epson
Epson S5U1C17965T2 Bedienungsanleitung
Epson
Epson S5U13705B00C Bedienungsanleitung
Epson
Epson 5U13743P00C100 Bedienungsanleitung
Epson
Epson S5U13T04P00C100 Bedienungsanleitung
Epson
Epson S1R72U06 Bedienungsanleitung
Epson
Epson S5U13A05B00C Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
