Epson Ethernet Card Betriebsanleitung

EPSON

Ethernet Card Supplement

This guide includes new information about your EPSON®

multiprotocol Ethernet interface card and software.

If you are using the card with Apple® Macintosh a computers on

AppleTalk® or TCP/IP networks, please disregard the Macintosh

section in your EPSON Type B Ethernet Interface Card

User's

Guide

and follow the steps in this supplement.

In addition to the operating systems mentioned in the Ethernet card

User’s Guide, the card also supports Windows 95 and Windows NT

4.x.

You’ll find the following information in this Supplement:

Initializing the Ethernet card

Using the Ethernet Card with NetWare® on a WAN

Using Macintosh with the Ethernet Card

Using TCP/IP with Windows 95

CPD5719

Initializing the Ethernet Card

After you install the Ethernet card in a printer or reinstall it in a new

printer, plug in the printer while pressing down the status sheet

button for at least three seconds to initialize the card.

,.Ds

status sheet button

Printing a Status Sheet

You can print a status sheet after you finish initializing the card.

Turn on the printer and press the status sheet button. The status

sheet gives you information about the Ethernet card including the

current configuration, serial number, and address of the card. Keep

the status sheet; you need the information to configure the card.

Using the Ethernet Card With NetWare on a WAN

If you use the Ethernet card in a NetWare environment over a WAN

(Wide Area Network) and connect it to a general phone line

(including ISDN), the card may open the dial-up-router and packets

may be sent to the WAN. To avoid this problem and possible phone

fees, mask the vendor code in the dial-up-router as shown below:

Vendor code 00:00:48:xx:xx:xx

For details on how to mask the vendor code, ask your network

administrator or see your NetWare documentation.

EPSON Ethernet Card Supplement

Using Macintosh with

the

Before configuring the Eth

printer driver is installed i

turned on and the Etherne

your Ethernet card

User's

(

more information.)

The information on

Macin

sections:

Cl Installing EPSON Net!

Monitoring the

Printer

Configuring the Ether:

for Macintosh

Note:

you are using Macintosh

(

the card using EPSON Net

workstation or EPSON Nei

workstation. See your Ether

Installing EPSON Net!

To install EPSON Net! for

Turn on your

Macinto;

Create a folder for

EPS

Insert the EPSON Net!

Copy the program

fro]

Monitoring the Printers on

You can monitor and

checl

your network according tc

Using Macintosh with the Ethernet Card

Before configuring the Ethernet card, check to see if the correct

printer driver is installed in the Macintosh. Make sure the printer is

turned on and the Ethernet card is connected to the network. (See

your Ethernet card User’s Guide and your printer User’s Guide for

more information.)

The information on Macintosh is explained in the following

sections:

Installing EPSON Net!

Monitoring the Printers on Your Network

Configuring the Ethernet Card for AppleTalk

Configuring the Ethernet Card for TCP/IP Using EPSON Net!

for Macintosh

Note:

lf you are using Macintosh computers on a NetWare network, configure

the card using EPSON Net! for NetWare Windows from a Windows

workstation or EPSON Net! for NetWare DOS from a DOS

workstation. See your Ethernet card User’s Guide for instructions.

lnstalling EPSON Net!

To install EPSON Net! for Macintosh, follow these steps:

Turn on your Macintosh.

Create a folder for EPSON Net! on your hard drive.

Insert the EPSON Net! for Macintosh disk in the drive.

Copy the program from the disk to the folder.

Monitoring the Printers on Your Network

You can monitor and check the status of all printers connected to

your network according to the protocol you use.

EPSON Ethernet Card Supplement

To check the status of all printers that are turned on and enabled for

a protocol, follow the steps below:

Open the EPSON Net! folder and click the EPSON Net! icon.

The following window appears:

Note:

If you don‘t see any printers in the list, try selecting the zone that the

printer is in or all zones by following the steps in the next section.

To exit EPSON Net!, click Quit.

Selecting a Zone

You can select which printers to monitor according to their zone or

address. You must select a zone before you configure the Ethernet

card in the Configuration dialog box. Follow these steps:

With the EPSON Net! dialog box open, choose Zone from the

Options menu bar.

Click a zone to select it

clicking multiple zones

3. Click OK.

EPSON Net! sends a

packe,

current printer’s status.

The

latest information about

the

Sorting the Printers

Follow these steps to sort

With the EPSON Net!

(

Options menu bar.

sort

by Zone

by Serial No

by Printer

nar

Click any of the sort op

The EPSON Net! dialog bo:

selected sort option.

EPSON Ethernet Card Supplement

Click a zone to select it, press and hold the Shift key while

clicking multiple zones to select them, or click Select All.

3. Click OK.

EPSON Net! sends a packet to the selected zones and detects the

current printer’s status. The EPSON Net! dialog box shows the

latest information about the printers located in that zone.

Sorting the Printers

Follow these steps to sort the printers in the EPSON Net! dialog box:

With the EPSON Net! dialog box open, choose Sort from the

Options menu bar.

Click any of the sort options and click OK.

The EPSON Net! dialog box displays the printers according to the

selected sort option.

EPSON Ethernet Card Supplement 5

Setting the Refresh lnterval

Follow these steps to set the refresh interval for the settings in the

EPSON Net! dialog box:

With the EPSON Net! dialog box open, choose Preferences

from the Options menu bar.

Refresh interval (sec)

(DKI

[Cancel)

Type any value from 5 (default) to 90 seconds and click OK.

EPSON Net! monitors the printers by polling the network at the

intervals you specified.

Configuring the Ethernet Card for AppleTalk

Follow these steps to use EPSON Net! for Macintosh to configure

the Ethernet card for AppleTalk:

Note:

You must select a zone before you can configure the Ethernet card. See

page 4 for instructions.

Open the EPSON Net! folder and double-click the EPSON Net!

icon. The following window appears:

[o,,,]

(T)

Highlight the printer

Click Open.You see

Click the AppleTalk

ice

your Ethernet card is

Set the following optic

Available Zone:

the printer to app

Printer Name:

Th’

can rename it. If

to the network, be

Entity Type:

EPSG

type on an Appl

these options.

Network No.:

you should

lqx

click

Manual a

AppleTalk

P!#

available

connected

inactiG$

EPSON Ethernet Card Supplement

Highlight the printer you want to configure in the list.

Click Open. You see the Configuration dialog box:

4. Click the AppleTalk icon. Make sure the correct serial number of

your Ethernet card is displayed.

Set the following options in the AppleTalk Configuration box:

Available Zone: Select the network zone that you want

the printer to appear in.

Printer Name: The default printer name appears. You

can rename it. If the same types of printers are connected

to the network, be sure to give them unique names.

Entity Type: EPSON Net! displays the printer’s Entity

type on an AppleTalk network. You don’t have to set

these options.

Network No.: You may not see this option. If you do,

you should keep Auto selected. If you want to change it,

click Manual and enter a number.

AppleTalk I’S: You may not see this option. It is only

available when an EPSON PostScript® printer that is

connected to the network cannot make AppleTalk active

or inactive automatically.

EPSON Ethernet Card Supplement 7

Click OK to send the new settings to the Ethernet card and

return to the EPSON Net! dialog box. Click Update to send the

new settings to the card without closing the Configuration

dialog box.

Caution:

Once you make changes to the Ethernet card, wait at least five

minutes before turning off or restarting your printer.

Click Exit to exit EPSON Net! for Macintosh.

Configuring the Ethernet Card for TCP/IP Using EPSON Net! for

Macintosh

To configure the Ethernet Card for TCP/IP using EPSON Net! for

Macintosh, follow these steps:

Open the EPSON Net! folder and double-click the EPSON Net!

icon.

Note:

If you do not know how to find out your computer’s IP address or the IP

address for the Ethernet card, ask your network administrator, or follow

the instructions on page 11.

Highlight the printer you want to configure in the list.

Click Open to open the Configuration dialog box.

Click the

TCPAP

icon.

shows the correct

serk

Set the following optic

box:

II’ address: Deter

Ethernet card.

Subnet mask: Ass

Auto IP set: Click

Click Update to send

without closing the Co

send the new settings

Click Exit to exit EPSO

After configuring the

Ethe.

on each Macintosh and ma

correctly.

Using

TCP/lP

in Windows

You can configure the

Ethc

Windows 95 on a TCP

network.

Installing

TCP/lP

in Window

Click Start, point to Se

2. Double-click the Netw

EPSON Ethernet Card Supplement

Click the TCP/IP icon. Make sure the Configuration dialog box

shows the correct serial number of the target Ethernet card.

Set the following options in the TCP/IP Configuration dialog

box:

IP address: Determine and assign an IP address for the

Ethernet card.

Subnet mask: Assign the subnet mask.

Auto IP set: Click Off.

Click Update to send the new settings to the Ethernet card

without closing the Configuration dialog box. Or, click OK to

send the new settings and return to the EPSON Net! dialog box.

Click Exit to exit EPSON Net! for Macintosh.

After configuring the Ethernet card for TCP/IP, set up your printer

on each Macintosh and make sure that the TCP/IP network works

correctly.

Using TCP/IP in Windows 95

You can configure the Ethernet card for TCP / IP if you are using

Windows 95 on a TCP / IP network, or a Windows 95 peer-to-peer

network.

Installing TCP/IP in Windows 95

Click Start, point to Settings, and click Control Panel.

Double-click the Network icon.

If TCP/IP appears in the list of installed network components on

the Configuration menu, you can skip to “Configuring the

Ethernet Card for TCP/IP and Windows 95.” If TCP/IP does not

appear in the list, click Add.

EPSON Ethernet Card Supplement 9

Click Protocol and then the Add button.

Select Microsoft from the Manufacturers list and TCP/IP from

the Network Protocols list. Then click OK.

Click OK again and follow any on-screen instructions to enable

TCP/IP.

Configuring the Ethernet Card for TCP/IP and Windows 95

Make sure that the Ethernet card installed in the printer is on the

same network segment as the computer you are using to configure

the card. Also, find out that computer’s IP address and the IP

address that you will assign to the Ethernet card.

Note:

lf you do not know how to find out your computer’s IP address

the IP

address for the Ethernet card, ask your network administrator, or follow

the instructions that follow this section.

Follow these steps to configure the card:

Find the hardware address (node number) on the top of the

status sheet you printed out after initializing the card. (See

page 2.) If you need to, print out another status sheet.

Double-click the MS-DOS Prompt icon to open a DOS prompt.

Set up the routing table, using the following command:

ping <IP address>

for example: ping 127.0.1.1

Add an entry in the ARP table that assigns an IP address to the

hardware address of the Ethernet card. Use the following

command:

arp

-s <IP address> <node address>

for example: arp -s 127.0.1.200 00:00:48:92:BD:9A

Start a continuous “ping” to the card, using the following

command with the card IP address:

ping

<IP

address>

for

example: ping 12'

You see a message

sim

Reply from

127.0.1.21

Reply from 127.0.1.2

This shows that the

Etherne

If you receive 4 lines of

“Ret

correctly. Check to make

segment as the workstation

you typed in the correct II’

Before you can print using

’

Monitor and add a printer

User’s

Guide for instruction:

Note About

Addresses

If you don’t have a network

addresses in the range of

computer or other device

have a unique IP number. T

However, you should not u

direct (rather than dial-up)

EPSON Ethernet Card Supplement

Inhaltsverzeichnis

Andere Epson Netzwerkkarte Handbücher

Epson

Epson EFM144FP Bedienungsanleitung

Epson

Epson USB Bedienungsanleitung

Epson

Epson Network Interface Unit Bedienungsanleitung

Epson

Epson RS-485 Bedienungsanleitung

Epson

Epson B12B808393 - NETWORK IMAGE EXPRESS CARD Abmessungen

Epson

Epson C82332* Bedienungsanleitung

Epson

Epson C82305 Series Bedienungsanleitung

Epson

Epson C82314* Bedienungsanleitung

Epson

Epson C82324* Bedienungsanleitung

Epson

Epson C82372 Bedienungsanleitung

Epson

Epson UB-E02 Gebrauchs- und Pflegehandbuch

Epson

Epson B12B808393 Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung

Gigafast

Gigafast EE101-AEX Bedienungsanleitung