Epson 1400 CFS Bedienungsanleitung

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Installation Instructions: Epson 1400 CFS

Epson 1400 with MIS CFS Installed *A perfect print with OEM cartridges is a must*

Prerequisite

Before starting this installation, you MUST test your printer to make sure it is printing

100% correctly. The best way to do this is to first print a Nozzle pattern, using the

printer utility software provided by Epson. Once a perfect nozzle pattern is achieved,

print 5 copies of the MIS

purge6.tif

image using the Plain Paper and 360 dpi settings on

the printer. All 5 pages must print without banding or skipping (white spaces). If your

printer cannot do this, do not install the CFS. Run no more than 3 cleaning cycles or get

new cartridges. Do not proceed until you can pass these tests. The Purge6 image can be

found on the diskette included with your system. If you have a Mac you can download it

from our website. You can also get it from the Helpdesk Download Library.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Tools needed

Tools & Materials Needed –

•MIS CFS System, ink, and a working Epson 1400 printer

•Ruler or measuring tape

•Pair of scissors

•Alcohol and some paper towels

•Flat tip screw driver

•OEM Cartridges (For testing printer)

•Some paper to print on

Step 1

If you purchased your system prefilled, go to Step 2. If you purchased an empty CFS unit,

then vacuum fill the cartridges with the ink that came with the system or the ink of your

choice. Follow the instructions that are included with the vacuum pump, go to the pages

near the end of this document. When this is complete, go to Step 2.

Step 2

On the printer, push the Ink button to move the cartridges to the eplacement position.

Ink Replacement Button

While in this position, pull the power plug out of the wall. Next, remove the cartridges.

The cartridges ride in a black cartridge carriage and are secured by a gray cover that

must be raised in order to remove the cartridges.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Unplug printer from wall

Step 3

The cartridge cover also needs to be removed. This is the gray colored cover that holds

the cartridges down when they are installed in the printer.

First, locate the cartridge cover retaining clip, it is located on top of the printer carriage.

INSTALLATION NOTE -. Attempts to remove this cover may result in damage to the

cover. The absence of this cover does NOT prevent normal operation of the printer in any

way.

Cartridge cover clip

Next, carefully pry the clip forward so that it will unlock from the printer carriage and

release the carriage cover.

Gently pry clip forward to remove

When the clip releases it can be removed. Please note that due to the design of this clip

it may be damaged during removal thus making it impossible to reinstall the carriage cover

in the future. If your clip does get damages the printer will still operate normally.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

With the cartridge cover retaining clip removed you can easily remove the carriage cover

exposing the OEM cartridges that are installed in the printer.

Remove cover and store in a safe place

Note: We recommend storing the cover and clip that were

removed in Step 3 in a zip lock storage bag so that they do not

become separated and lost.

Step 4

Remove the OEM cartridges from the printer and store them in a zip lock bag. It is best

to save these cartridges so that they can be used for diagnostic purposes or if the

printer must be sent in for service.

Remove OEM cartridges

Step 5

The next step is to mark the location of the 1400 Bridge Bracket. This bracket must be

accurately located for proper system operation and to avoid complications.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Measure 6 1/2” from the back edge, left side, of the larger two openings in the top of the

printer housing. Using a marker or pencil place a line across the center divider between

the two access holes. This is the location of the top of the 1400 Bridge Bracket.

Place mark 6 1/2” from the back of the larger opening

Close up of measurement

After marking the location of the back edge of the clip, the 1400 bridge bracket can be

installed. When installing the bracket, be sure to line up the left most edge of the clip

with the mark that you have just made. Note that the bent part of the bracket should be

toward the front of the printer.

Install 1400 Bridge Bracket using the mark to locate the left edge

Step 6

The next step is to mark the location of the Beige Clip. This clip will be installed in line to

the right of the 1400 bridge bracket.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Mark location for Beige Clip

Install the clip with the open side facing the back of the printer and the hinge toward the

front of the printer housing. The back of the clip should be 1 ½” from the rear grove in

the housing and the right side of the clip should be touching the groove in the housing.

Finally, check that the Beige Clip and 1400 Tube Clip are in line (parallel with the front and

back of the printer openings) with a straight edge or ruler.

Verify 1400 Tube Clip and Beige Clip are in line

Step 7

Move the cartridge carriage to the opening in the center of the printer housing by pushing

it from the right.

Move carriage with hand over to the left most access hole (center of printer)

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Note: Before continuing, check that each CFS cartridge has a chip, as cartridges

without a chip can damage the printer.

Install the CFS cartridge through the left opening in the printer housing. As the

cartridges are installed, listen for a click to ensure that they are properly seated.

Install CFS cartridges

Using your hand, push the carriage all of the way to the left side of the printer. This will

help in positioning the tubes into the clips that were installed in Steps 5 and 6.

Step 8

Ensure that the 1400 Tube Guide and Beige Clips are open and that the carriage is pushed

all of the way to the left inside the printer. Guide the tubes through the 1400 Tube Clip

and Beige Clip. You will want to make sure that the tubes do not twist or bend as this will

confuse the color order and interfere with proper bottle connection. Note that the cyan

tube is to the front with the black toward the back of the printer.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Guide the tubing through the clips so that is does not twist or flip

First, route the tubing into the 1400 Tube Clip so that there is not any slack on the left

side of the clip, but not tight enough so as to stretch the tubing. Close the 1400 Tube

Clip. Next, route tubing into Beige Clip so that the tubing does not sag between the 1400

Tube Clip and the Beige. Finally, Close the Beige Clip.

Test for proper tube position by moving the carriage from left to right and back. If at

any point the tubing becomes tangled or there is any drag on the carriage you will need to

move the carriage back to the left and repeat Step 8.

Proper tube installation

Step 9

Now that the CFS is installed in the printer, and proper tube position has been verified we

can un web the tubing to the right of the beige clip. To un web the tubing, grasp two

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

individual tubes that are next to each other and peal apart. Once you have completed un

webbing verify that the tubing is in the correct order. Front to back, (C, M, Lm, Lc, Y, K).

Unweb the tubing by pealing each tube apart up to the Beige Clip, then verify color order

Next, install the caps with fittings onto the ink bottles supplied with your CFS. If these

caps were installed during Step 1 (filling an empty CFS) then they will already be installed.

Install the caps with fittings onto full bottles of ink

Using the Velcro dots provided, install the bottles in correct ink order below.

Bottle order front to back (C, M, Lm, Lc, Y, K)

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Place the bottles on the right side of the printer in the order shown above

Before trimming each tube and connecting them to the fittings on the bottles, double

check that your bottles and tubes are in the proper color order.

Recheck proper tube color of tubes coming as they come out of the Beige Clip

The tube lengths will need to be trimmed so that the tube will connect to the fitting on

top of the bottle without having a large amount of slack. The best way to accomplish this

is to pull the tube over next to the bottle and mark the tube with a ball point pen at the

point where the tube and the bottom of the bottle cap meet.

Set up the bottles as shown, and work with one tube at a time, starting with the magenta

tube. Test the length of this tube by placing it near the bottle, on the outside, and see if

it is going to reach the bottom of the bottle cap. It should not be too short. If it looks

like it is going to be too long, then mark the tube with a ball point pen at the spot you

think it should be cut.

Remove the white plug from the end of the tube and cut the tube with scissors where you

placed the mark. After cutting the tube immediately connect it to the bottle. SAVE

THE WHITE PLUGS as they will be needed if you ever remove the CFS System from your

printer.

Make sure the correct color tube goes onto the correct color ink bottle. A mistake here

will ruin the whole system and you will need to purchase an empty cartridge set w/ tubes.

Andere Epson Drucker Handbücher

Epson

Epson LX-810 Bedienungsanleitung

Epson

Epson Stylus COLOR 3000 Bedienungsanleitung

Epson

Epson SureColor T3470 Bedienungsanleitung

Epson

Epson WF-2830 Bedienungsanleitung

Epson

Epson Stylus Pro 7700 Series Bedienungsanleitung

Epson

Epson PP-100N - Discproducer - DVD Duplicator x2 Bedienungsanleitung

Epson

Epson LX-300+II RTP Bedienungsanleitung

Epson

Epson TM-U220 Series Bedienungsanleitung

Epson

Epson 785EPX - Stylus Photo Color Inkjet Printer Installationsanleitung

Epson

Epson Stylus Color 980 Bedienungsanleitung

Epson

Epson TM-T20 Bedienungsanleitung

Epson

Epson SC-F10030H Series Bedienungsanleitung

Epson

Epson Stylus color 600 Bedienungsanleitung

Epson

Epson EcoTank ET-M1170 Bedienungsanleitung

Epson

Epson Stylus C87 Bedienungsanleitung

Epson

Epson WorkForce WF-3640 Service-Handbuch

Epson

Epson SureColor T2170 Bedienungsanleitung

Epson

Epson EPL-N3000 Bedienungsanleitung

Epson

Epson 7800 - Stylus Pro Color Inkjet Printer Gebrauchs- und Wartungshandbuch

Epson

Epson TM-P80 Gebrauchs- und Pflegehandbuch

Epson

Epson TM-T88V-i Bedienungsanleitung

Epson

Epson C3900 Series Bedienungsanleitung

Epson

Epson WorkForce WF-7110 Bedienungsanleitung

Epson

Epson SureColor F10070 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung

IRA3D

IRA3D POETRY4 Bedienungsanleitung

Ricoh

Ricoh Aficio AP400 Bedienungsanleitung

BIXOLON

BIXOLON SRP-352plusV Bedienungsanleitung