Epson LQ-1000 - Impact Printer Abmessungen
EPSON AMERICA, INC.
EPSON
Product Support Bulletin
Subject:
24 Pin Printer Error and Beep Codes
Date: 4/3/91
PSB No: P-0076
Page(s): 1 of 4 Originator JV
Epson printers issue beep tones when certain error conditions exist. Those beeps
can assist you in locating and repairing customer’s printers. The following error
codes are listed by product name.
NOTE:
Most of the beeps issued by the printers are of .1 second duration with a .1
second pause between beeps. Where the beeps or the pauses are longer,
it has been noted in the text. The description “3 Beeps x 2” means two sets
of three beeps.
LQ-200/AP-3000
1 beep: BEL code
1 beep: A Control Panel setting is accepted.
3 beeps: Paper End detected
5 beeps: Abnormal carriage movement
On-Line light is flashing:
Printhead is over heated. Carriage will stop until
the printhead cools down.
LQ-500, LQ-510, LQ-1010, LQ-850, LQ-950, LQ-1050,
L1000, AP-4000, AP-4500
1 beep:
BEL code (.5 set beep)
1 beep: A Control Panel setting is accepted
3 beeps: Paper End detected
5 beeps: Abnormal carriage movement
PSB No: P-0076
Page: 2 of 4
LQ-800, LQ-1000, L750
1 beep: BEL code
1 beep: A Control Panel setting is accepted
3 beeps: Paper End detected
5 beeps:
Abnormal carriage movement
(.5 sec. pause between beeps)
5 beeps:
LQ-860
+35V supply is abnormal
1 beep: BEL code (.5 sec. beep)
1 beep:
A Control Panel setting is accepted
3 beeps: Paper End detected
5 beeps:
Color select mechanism error
(.5 sec. beep, .5 sec between beeps)
5 beeps:
Abnormal carriage movement
(.5 sec. beep, .5 sec between beeps)
5 beeps:
CG ROM failure
(.5 sec. beep, .5 sec between beeps)
LQ-1500
1 beep:
BEL code
5 beeps: Paper End detected
5 beeps: Abnormal carriage movement
(.5 sec. pause between beeps)
PSB No: P-0076
Page: 3 of
4
LQ-2500
NOTE:
Printers with LCD displays use error messages along with beeps to
inform the user of problems. The following messages will help you to
troubleshoot problems.
A blank LCD screen with the Power-on LED lit can be caused by a bent
pin on one of the PROM
S
or jumper J1 may be set incorrectly.
1 beep: BEL code
5 beeps: Abnormal voltage-
5 beeps: Abnormal carriage movement
(.5 sec. pause between beeps)
LQ-2500 LCD Codes:
00 Invalid ID request to CGROM
03
EEROM read/write error
10
LQ-2550
Abnormal carriage movement
1 beep: BEL code
3 beeps:
Paper End detected
5 beeps: Abnormal carriage movement (.5 sec. pause between
beeps)
5 beeps: Platen Gap adjustment error (.5 sec. pause between
beeps)
5 beeps: Case open
LQ-2550 LCD Codes:
00 (1)
The font could not be found. The printer’s internal program could not
find the target font.
(2)
Missing or damaged 7A ROM
02
Internal ROM check does not match. The versions may have been mixed.
PSB No: P-0076
Page:
4
of
4
LQ-2550 cont.
03
10
11
12
20
A ‘Verify After Write” check to the SRAM has failed. The SRAM could be bad.
This is a motor control error. Four possible areas of failure are:
a. CR home condition not detected at power up
b. Platen gap motor HP not detected correctly
c. Friction/Tractor feed switching error
d. Physical obstruction such as a jammed ribbon
Skewed paper detect error. Since the initial reading upon loading a single
sheet paper, the paper has skewed. This is a printhead wire protection
feature.
Illegal paper positioning.
(1)
If the paper is loaded using the knob instead of the LOAD/EJECT switch,
this error condition will occur. This is a printhead wire protection feature.
(2)
PE sensor may have failed or is not connected.
CPU error. An undefined op-code was detected.
NOTES:
Error codes 11 and 12 are usually caused by new operators who are
un-familiar with the machine. Both of these errors are corrected by
turning the printer off, taking out the paper and turning the printer back
on. Both features were added to ensure proper paper handling and
prevent paper jams, which can result in printhead failures.
Incorrect jumper settings on the ROMA board may cause errors 10 or
20. The correct settings are documented in the Service Manual (page
A-54, figure A-52) and on TIB LQ2550-005.
Errors 0,2, 3, 10, and 20 may require a repair, adjustment or
replacement.
EPSON
EPSON AMERICA. INC.
SERVICE
P
RODUCT
S
UPPORT
B
ULLETIN
Date: 3/1/88
Subject:
Epson Printer/Ribbon Compatibility
Number: P-0013A
PURPOSE:
This list will assist in
ribbons to printers.
the correct matching
of Epson
The numbers listed below are the Epson part
numbers and can be used to order ribbons.
This list supercedes
PSB-013.
EAI #
7751
N/A
7753
N/A
7754
N/A
7756
N/A
7757
N/A
8750
ERC-04
8753
ERC-13
8755
ERC-08
8759
ERC-14
8760
ERC-16
8762
ERC-17
8763
N/A
8764
N/A
*Recommended for use when color is not required.
OEM # USAGE
ALL DX
LQ-500, LQ-800, LQ-850
LQ-1000, LQ-1050
LQ-2500 (
BLACK
)
LQ-2500 (COLOR)
ALL 80-COLUMN MX, RX, FX,
FX-86e,
LX-800, JX-80*
LQ-1500
ALL 136-COLUMN MX, RX, FX,
FX286e
JX-80 (COLOR)
P-80
LX-80, LX-86, LX-90, HW-10
EX
-800/1000 (
BLACK
)
EX-800/1000 (COLOR)
EPSON AMERICA SERVICE, 23610 TELO AVENUE, TORRANCE, CALIF. 90505
EPSON
EPSON AMERICA INC.
SERVICE DEPARTMENT
PRODUCT
SUPPORT
BULLETIN
DATE: 06/24/87
P-0007
SUBJECT: LQ-800/1000 IBM GRAPHICS CHARACTER PRINTING
Here at Product Support we receive numerous questions about
the printing of IBM-type graphics on the LQ-800/1000 printers,
and about the difference between the ESC/P and IBM identity
modules.
The purpose of this bulletin is to address these
common questions.
Printing IBM Graphics Characters
The LQ-800/1000 cannot print the IBM graphics characters unless
it has either the ESC/P (#7696) or the IBM (#7695) identity
module installed.
Module Differences
Various options are available when using the identity modules,
depending on which is used.
The ESC/P provides the character
graphics forms from the IBM standard character set, as well as
Greek alphabet characters,
and some mathematical operation
symbols.
In comparison,
the IBMmodule has the Alternate
and Symbol character sets, in addition to the standard set.
These may be required for some applications.
Software commands also differ between the two modules.
The
ESC/P module will allow use of all standard Epson printer
commands normally available to the LQ printers, whereas the
IBM module causes the LQ printer to emulate an IBM 5152
printer,
with the loss of some Epson printer commands normally
available to the LQ.
All font modules are usable with either identity module.
Inhaltsverzeichnis
Andere Epson Drucker Handbücher
Epson
Epson EPI-4000 Bedienungsanleitung
Epson
Epson Stylis Pro 9860 Bedienungsanleitung
Epson
Epson WorkForce Pro WP-4515 Bedienungsanleitung
Epson
Epson TM-S2000 Series Gebrauchs- und Pflegehandbuch
Epson
Epson TM-C3500 Series Bedienungsanleitung
Epson
Epson Stylus Photo 890 Bedienungsanleitung
Epson
Epson CX5000 - Stylus Color Inkjet Bedienungsanleitung
Epson
Epson PLQ-22CS Bedienungsanleitung
Epson
Epson TM-T20II Bedienungsanleitung
Epson
Epson J7000 - TM B/W Inkjet Printer Bedienungsanleitung
Epson
Epson XP-600 Montageanleitung
Epson
Epson SC-S80600L Series Bedienungsanleitung
Epson
Epson TM-T90 Bedienungsanleitung
Epson
Epson WorkForce 40 Series Bedienungsanleitung
Epson
Epson ET-4700 Series Bedienungsanleitung
Epson
Epson AcuLaser C8600 Bedienungsanleitung
Epson
Epson TM-T88II Series Bedienungsanleitung
Epson
Epson M1120 Bedienungsanleitung
Epson
Epson 1520 - Stylus Color Inkjet Printer Technisches Datenblatt
Epson
Epson FX-890II Bedienungsanleitung
