Epson SureColor F7070 Bedienungsanleitung
Epson® SureColor®
F7070 Setup Guide
2|
Contents
Unpacking the Printer ...........................................................................................................................3
Assembling the Stand .............................................................................................................................6
Installing the Printer ............................................................................................................................10
Installing the Media Feeding Unit .......................................................................................................15
Installing the Take-up Reel System ......................................................................................................19
Setting the Language ............................................................................................................................22
Adjusting the Media System ................................................................................................................23
Loading Media ....................................................................................................................................25
Installing the Software .........................................................................................................................31
USB Installation ............................................................................................................................32
Network Installation .....................................................................................................................33
Unpacking the Printer |3
Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions
marked on the printer and in the User’s Guide.
Unpacking the Printer
Before beginning assembly, make sure you have sufficient space to set up and use the printer. The
following illustration shows the minimum space required for using the printer:
Callout Distance
1 19.7 in. (500 mm)
2 3.9 in. (100 mm)
3 68.9 in. (1750 mm)
4 39.4 in. (1000 mm)
5 114.3 in. (2903 mm)
6 19.7 in. (500 mm)
7 39.4 in. (1000 mm)
8 142.5 in. (3620 mm)
4|Unpacking the Printer
When choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations
subject to direct sunlight, excessive heat, humidity, or dust. Be sure the printer is placed on a flat, stable
location that can support 496 lb (225 kg).
Caution: Six people are required to unpack and install the printer.
You need an even larger floor space to assemble the printer and stand, so be sure to prepare a large, clear
area before unpacking them. Also make sure you save the box and packaging in case you need to ship the
printer later.
The following items should be included with your printer:
Printer and Stand Assembly
Printer
Carry bars
Horizontal struts
Power cord
Software and
documentation
Hex wrench
Legs
Waste ink
tank bracket
Waste
ink tank
Caution label
Cable
support Waste ink tube
bracket
Unpacking the Printer |5
Media System Assembly
The items below can be found in the “Ink Supply System Cover 1” box.
Media feeding unit
Take-up reel
Reel brackets
Adjustment paper
Roll core
Bracket and mounting
hardware
6|Assembling the Stand
Assembling the Stand
Make sure you have the following items before assembling the stand.
1. Slide the large horizontal strut into both of the legs.
2. Use the long end of the hex wrench to tighten the pre-placed screws on each of the legs.
back of stand
Assembling the Stand |7
3. Attach the smaller horizontal strut by securing two B screws (four total) in the back of the right and
left legs.
4. Attach the waste ink tank bracket and secure it with a B screw.
5. Attach one B screw to the other side of the bracket, move the slider into place, then attach another B
screw.
8|Assembling the Stand
6. Temporarily fasten the waste ink tube bracket using one B screw.
7. Remove the four screws, then remove the plastic piece.
8. Loosely fasten the mounting pieces to the bracket using three D screws and six washers.
Assembling the Stand |9
9. Slide the mounting pieces into the grooves, as shown.
10. Remove the screw, align the bracket, then fasten the screw to the stand.
11. Tighten the screws.
10 |Installing the Printer
12. Replace the plastic piece and then fasten it using the screws from step 7.
Installing the Printer
You need six people to install the printer; four people to carry it and two people to position it on the stand.
Use the carry bars to lift and move the printer.
Make sure you have the following items before installing the printer.
1. Lock the casters and fix the stand in place. To fix the stand, rotate the feet clockwise until they’re
firmly placed on the ground.
Andere Handbücher für SureColor F7070
3
Inhaltsverzeichnis
Andere Epson Drucker Handbücher
Epson
Epson EC-C110 Bedienungsanleitung
Epson
Epson L800 Bedienungsanleitung
Epson
Epson Stylus Photo R265 Series Bedienungsanleitung
Epson
Epson LQ-570e Bedienungsanleitung
Epson
Epson ET-3843 Bedienungsanleitung
Epson
Epson 1520 - Stylus Color Inkjet Printer Bedienungsanleitung
Epson
Epson 2200 Lumens Installationsanleitung
Epson
Epson WorkForce WF-2870 Series Bedienungsanleitung
Epson
Epson Artisan 635 Bedienungsanleitung
Epson
Epson DFX-8500 - Impact Printer Bedienungsanleitung
Epson
Epson Perfection 1200PHOTO Bedienungsanleitung
Epson
Epson C31C213A8941 Bedienungsanleitung
Epson
Epson WorkForce WF-3620 Bedienungsanleitung
Epson
Epson SureColor P600 Series Bedienungsanleitung
Epson
Epson TM-L90 series Bedienungsanleitung
Epson
Epson Stylus SX525WD Montageanleitung
Epson
Epson Stylus Photo 925 Benutzerhandbuch
Epson
Epson 480SX Installationsanleitung
Epson
Epson L110 Bedienungsanleitung
Epson
Epson LX-300 Bedienungsanleitung
