Epson TM-H6000IV-DT Bedienungsanleitung

User’s Manual

Important Safety Information. . . . . . . . . . . . . . . . . . .page 2

Part Names and Functions. . . . . . . . . . . . . . . . . . . . . .page 5

Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 8

Basic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13

Installing/Replacing the Ribbon Cartridges . . . page 16

Loading Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 23

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 25

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 27

M00080802EN

English

Important Safety Information

This manual presents important information intended to ensure safe and effective use of this

product. Read this manual carefully and store it in an accessible location.

If Windows Embedded POSReady7 is installed on your model, be sure to read “MICROSOFT

SOFTWARE LICENSE TERMS” at the end of this manual before you start using the product. If you do not

accept any one of the terms, do not use the product.

For information on development of a system with this product and setup, see also Technical

Reference Guide. You can access Technical Reference Guide from the included Manual CD.

Key to Symbols

The symbols in this manual are identified by their level of importance, as defined below. Read the

following carefully before handling the product.

!WARNING:

Warnings must be observed carefully to avoid serious bodily injury.

!CAUTION:

Cautions must be observed to avoid minor injury to yourself, damage to your equipment, or loss of

data.

QNote:

Notes have important information and useful tips on the operation of your product.

Safety Precautions

!WARNING:

❏

If this product produces smoke, a strange odor, or unusual noise, immediately unplug the

AC cable, and then contact your dealer or an Epson service center for advice. Continued

use may lead to fire or electric shock.

❏

Do not use this product with any voltage other than the specified one. Doing so may lead

to fire or electric shock.

❏

Be sure to use the specified AC adapter [AC adapter, T (Model: M284A)]. Connection to an

improper power source may lead to equipment damage, fire, or electric shock.

❏

Do not connect the cables in ways other than those specified in the manuals. Different

connections may cause equipment damage or fire.

❏

Do not block the openings of this product. This may cause overheating inside the product

and lead to fire.

• Do not place the product in an unventilated narrow location, such as a bookshelf.

• Do not place the product on carpet.

• Do not cover the product with any fabric.

❏

Do not use this product where inflammable fumes of gasoline, benzine, thinner, or other

inflammable liquids may be in the air. Doing so may cause an explosion or fire.

English

❏

Do not use aerosol sprayers containing flammable gas inside or around this product.

Doing so may cause fire.

❏

If water or other liquid spills into this product, immediately unplug the AC cable, and then

contact your dealer or an Epson service center for advice. Continued use may lead to fire

or shock.

❏

Do not allow foreign objects to fall into this product. Penetration by foreign objects may

lead to fire or electric shock.

❏

Never attempt to repair this product yourself. Improper repair work can be dangerous.

❏

Never disassemble or modify this product. Tampering with this product may result in

injury, fire, or electric shock.

❏

Do not attempt to open or disassemble the internal lithium battery. This could result in

burns or release of hazardous chemicals.

❏

Do not leave the internal lithium battery in a hot place such as near a fire or a heater

because it could overheat and ignite.

!CAUTION:

❏

Do not use this product in locations subject to high humidity or dust levels. Excessive humidity

and dust may cause paper jams and other problems, such as fire, or electric shock.

❏

Be sure to set this product on a firm, stable, horizontal surface. The product may break or cause

injury if it falls.

❏

Do not stand on or place heavy objects on top of this product. Equipment may fall or collapse,

causing breakage and possible injury.

❏

Be sure to use this product with the connector cover attached. If it is not attached, foreign objects

may enter this product, causing fire or equipment damage.

❏

When you move this product, be sure to hold the main body. If you hold only the connector cover,

it may come off and the main body may break or cause injury if it falls.

❏

The print head can be very hot during and immediately after printing. If you need to touch it, such

as for cleaning, wait until it cools down. Touching it before that may cause burns.

❏

Be careful of the cutter blades of the printer unit.

❏

Make sure that the total power requirements of all devices receiving power from this product do

not exceed the power supplying capability of the product. Otherwise, the devices may be

damaged.

❏

Connecting an outdoor overhead LAN cable directly to this product may lead to lightning

damage. If you need to connect such a cable to the product, the cable must be protected against

an electrical surge between the cable and the product. You should avoid connecting the product

to a non-surge protected outdoor overhead LAN cable.

❏

Do not connect a telephone line to the drawer-kick connector of this product. The telephone line

or product may become damaged.

❏

To ensure safety, unplug this product before leaving it for an extended period.

English

Caution Labels

The caution label on the product indicates the following precautions.

!KCAUTION:

Do not touch the thermal head because it can be very hot after printing.

English

Part Names and Functions

Roll paper cover

Open this cover to install/replace the roll paper.

Receipt unit cover

Open this cover to install/replace the ribbon cartridge for endorsement printing.

Front cover

Open this cover to install/replace the ribbon cartridge for front slip printing.

Power button cover

Open this cover to operate the power button and the printer reset button.

Power button

Press this button to turn on or shut down the product. Keep pressing the button to turn off the

product forcibly. (U“Forced Termination” on page 15)

Printer reset button

Keep pressing this button with a pointed object (such as a pen) until the (Power) LED goes off to

reset the printer unit.

Connector cover

Attach this cover to protect cables. (U“Attaching/Removing the Connector Cover” on page 12)

Power button

Front cover

Release button

Roll paper cover

Printer reset button

Connector cover

Printer LEDs

Receipt unit cover

Power button cover

Controller LEDs

Feed button

English

Release button

Press this button to release the retained slip paper.

Feed button

Press this button to feed the roll paper.

Controller LEDs

Indicates the controller unit status.

Printer LEDs

Indicates the printer unit status.

LED LED status Meaning

➀Status LED

(Green)

On Power is on.

Flashing (with approx. 1 sec

intervals)

Standby.

Off Power is off.

➁Status LED 

(Orange)

Flashing (with approx. 1 sec

intervals)

Booting/Shutdown/Updating software.

Flashing (with approx. 160

msec intervals)

CPU temperature is high.

➂Storage access LED

(Green)

On Accessing storage.

LED LED status Meaning

➀(Power) LED

(Green)

On Power is on.

Off Power is off.

➁Error LED

(Orange)

On Offline.

Flashing An error has occurred.

Off In normal status.

➂Paper LED

(Orange)

On Roll paper near-end.

Flashing Waiting for the self-test printing to be continued.

Off There is a sufficient amount of roll paper remaining.

➃Slip LED

(Green)

On Slip paper mode.

Flashing Waiting for slip paper to be inserted/removed.

Off Roll paper mode.

English

Interface

All the ports and connectors are located on the back of the product.

QNote:

If the connector cover is attached, remove it to access the connectors. (U“Attaching/Removing the

Connector Cover” on page 12)

USB ports (× 3)

VGA port

Line-out port

Ethernet port

DC-in connector

Drawer kick connector

Serial port

Powered USB ports

(× 3)

DisplayPort

English

Setup

Installing the Product

Install the product horizontally on a firm, stable surface.

!CAUTION:

Do not place the product near any magnetic fields to avoid decreasing the MICR recognition rate.

QNote:

The security hook on the back of the product allows you to attach a commercially available antitheft

wire.

Security hook

English

Connecting External Devices

If you connect external devices, turn off the product and then connect each cable to the port/

connector on the back of the product. (U“Interface” on page 7)

!CAUTION:

When connecting external devices to the USB and powered USB ports, follow the precautions below.

❏

Confirm the rated current of the external devices by checking the descriptions on the devices or

manuals. Do not use a device whose rated current is unclear. Connect the external devices only

when those total power consumption is 30 W or less. (when print density is set to standard.)

❏

When you use powered USB ports, make sure that the TM-H6000IV-DT is turned off before

connecting each cable. When the powered USB mode (See the following section.) is set to Mode 2,

also make sure that the AC cable is disconnected from a power outlet before connecting it.

QNote:

When connecting the cables whose connectors do not lock themselves (USB cables and line-out cable),

pass the cables through the wire saddle to prevent them from coming off.

Wire saddle

English

Powered USB mode setting

The product has 2 powered USB modes and is initially set to Mode 1.

❏Mode 1: Power is supplied/not supplied for the powered USB ports when the product

power is turned on/off, in accordance with the operation of the power button.

❏Mode 2: Power is always supplied for the powered USB ports regardless of the

operation of the power button.

To change the powered USB mode setting, follow the steps below.

1. Make sure that the product is turned off.

2. Remove the 2 screws to remove the cover.

3. Use tweezers to change the position of the switch.

4. Fix the cover with the 2 screws.

Andere Handbücher für TM-H6000IV-DT

Inhaltsverzeichnis

Andere Epson Drucker Handbücher

Epson

Epson TM-T70 Bedienungsanleitung

Epson

Epson PM-525 Bedienungsanleitung

Epson

Epson Stylus C82N Bedienungsanleitung

Epson

Epson OFFICE 960FWD Bedienungsanleitung

Epson

Epson TM-T81III Bedienungsanleitung

Epson

Epson 850N Bedienungsanleitung

Epson

Epson Stylus Color 900 Bedienungsanleitung

Epson

Epson PICTUREMATE PM 225 Bedienungsanleitung

Epson

Epson Stylus Pro 4800 Portrait Edition Bedienungsanleitung

Epson

Epson 11880 - Stylus Pro Color Inkjet Printer Bedienungsanleitung

Epson

Epson U950 - TM B/W Dot-matrix Printer Bedienungsanleitung

Epson

Epson 3880 - Stylus Pro Color Inkjet Printer Bedienungsanleitung

Epson

Epson ActionLaser 1100 Bedienungsanleitung

Epson

Epson SureColor F2270 Bedienungsanleitung

Epson

Epson U295 - TM B/W Dot-matrix Printer Bedienungsanleitung

Epson

Epson C2600/2600 Bedienungsanleitung

Epson

Epson SC-T5400 SERIES Bedienungsanleitung

Epson

Epson Stylus Pro 10000CF Benutzerhandbuch

Epson

Epson AcuLaser C4000 Bedienungsanleitung

Epson

Epson Stylus C44UX series Bedienungsanleitung

Epson

Epson SC-T5100 Series Handbuch

Epson

Epson TM-T88 ReStick Bedienungsanleitung

Epson

Epson PictureMate CZ 283 Bedienungsanleitung

Epson

Epson DFX 8000 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung