Epson TM-T88III series Bedienungsanleitung

TM-T88III

User’s Manual / ユーザーズマニュアル

聞喘傍苧慕 / 聞喘傍苧慕

401463804

Printer Parts

DIP Switch Tables

ERROR

POWER

PAPER

OUT

FEED

ERROR

POWER

PAPER

OUT

FEED

1printer cover

4control panel

cutter cover

3cover open button

Serial

SW Function ON OFF

1-1 Data receive error Ignored Prints “?”

1-2 Receive buffer capacity 45 bytes 4K bytes

1-3 Handshaking XON/XOFF DTR/DSR

1-4 Data word length 7 bits 8 bits

1-5 Parity check Enabled Disabled

1-6 Parity selection Even Odd

1-7

1-8

Transmission speed (See table below.)

Transmission speed (bps)-bits per second 1-7 1-8

38400 ON ON

4800 OFF ON

9600 ON OFF

19200 OFF OFF

SW Function ON OFF

2-1 Handshaking

(BUSY condition)

Receive

buffer full

Offline or

Receive

buffer full

2-2 Do not change

2-3

2-4

Print density/

Low power

See Table A

2-5 Release

condition of

receive buffer

BUSY (If receive

buffer capacity

set to 4 KB.)

Releases BUSY

when remain-

ing receive

buffer capac-

ity reaches

138 bytes.

Releases BUSY

when remain-

ing receive

buffer capac-

ity reaches

256 bytes.

2-6 Do not change

2-7 I/F pin 6 reset Enabled Disabled

2-8 I/F pin 25 reset Enabled Disabled

Parallel

SW Function ON OFF

1-1 Auto line feed Always

enabled

Always disabled

1-2 Receive buffer

capacity

45 bytes 4K bytes

1-3 Selects paper

sensors to output

paper-end signals

(default value of

ESC c 3)

Disabled Paper roll end

sensor enabled,

Paper roll near-end

sensor enabled

1-4~

1-8

Undefined

SW Function ON OFF

2-1 Handshaking

(BUSY condition)

Receive

buffer full

Offline or

Receive

buffer full

2-2 Do not change

2-3

2-4

Print density/Low

power

See Table A

2-5 Release

condition of

receive buffer

BUSY (If receive

buffer capacity

set to 4 KB.)

Releases BUSY

when remain-

ing receive

buffer capac-

ity reaches

138 bytes.

Releases BUSY

when remain-

ing receive

buffer capac-

ity reaches

256 bytes.

2-6~

2-7

Do not change

2-8 I/F pin 31 reset

(Do not change)

Table A

Print density/low power SW 2-3 SW 2-4

– Low power consumption mode ON ON

1 (Normal) OFF OFF

2 (Medium) ON OFF

3 (Dark) OFF ON

TM-T88III User’s Manual 1

English

form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written

permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information

contained herein. While every precaution has been taken in the preparation of this book, Seiko Epson Corporation

assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for

damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of

this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to

strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or

any consumable products other than those designated as Original Epson Products or Epson Approved Products by

Seiko Epson Corporation.

EPSON and ESC/POS are registered trademarks of Seiko Epson Corporation.

NOTICE: The contents of this manual are subject to change without notice.

Safety Precautions

This section presents important information intended to ensure

safe and effective use of this product. Please read this section

carefully and store it in an accessible location.

WARNING:

Shut down your equipment immediately if it produces smoke, a strange

odor, or unusual noise. Continued use may lead to fire. Immediately

unplug the equipment and contact your dealer or a SEIKO EPSON

service center for advice.

Never attempt to repair this product yourself. Improper repair work can

be dangerous.

Never disassemble or modify this product. Tampering with this product

may result in injury or fire.

Be sure to use the specified power source. Connection to an improper

power source may cause fire.

Do not allow foreign matter to fall into the equipment. Penetration by

foreign objects may lead to fire.

If water or other liquid spills into this equipment, unplug the power cord

immediately, and then contact your dealer or a SEIKO EPSON service

center for advice. Continued usage may lead to fire.

2TM-T88III User’s Manual

English

CAUTION:

Do not connect cables in ways other than those mentioned in this

manual. Different connections may cause equipment damage and

burning.

Be sure to set this equipment on a firm, stable, horizontal surface. The

product may break or cause injury if it falls.

Do not use in locations subject to high humidity or dust levels. Excessive

humidity and dust may cause equipment damage or fire.

Do not place heavy objects on top of this product. Never stand or lean

on this product. Equipment may fall or collapse, causing breakage and

possible injury.

To ensure safety, unplug this product before leaving it unused for an

extended period.

Caution Labels

WARNING:

Do not connect a telephone line to the drawer kick-out connector;

otherwise, the printer and the telephone line may be damaged.

CAUTION:

The thermal head is hot.

CAUTION:

Caution label for autocutter blade.

TM-T88III User’s Manual 3

English

Unpacking

The following items are included with the standard specification

printer. If any item is damaged, contact your dealer.

❑Printer ❑Paper roll

❑Power switch cover ❑Connector cover *

❑AC adapter *

* May not be included with your printer.

Installing the Printer Horizontally or Vertically

You can install the printer horizontally on a flat surface (with the

paper exit on top) or vertically (with the paper exit at the front) by

hanging it on a wall, using the optional WH-10 hanging bracket set.

Control Panel

FEED button

This button feeds paper.

POWER LED

The POWER light is on when the printer is on.

ERROR LED

This indicates an error.

PAPER OUT LED

On indicates a paper near end or out. Flashing indicates standby.

Using the Power Switch Cover

WARNING:

If an accident occurs with the power switch cover

attached, unplug the power cord immediately.

Continued use may cause fire.

The enclosed power switch cover ensures that

the power switch is not pressed accidentally. To

use this cover, install it as shown on the right.

ERROR

POWER

PAPER

OUT

FEED

afT88IIIu_e..fm Page 3 Friday, February 20, 2004 12:09 PM

4TM-T88III User’s Manual

English

Attaching and Removing the Connector Cover

These instructions apply if a connector cover is packed with your

printer to protect your cables. To attach it, follow the steps below:

1. First, connect all the cables. The connector

cover has three possible cable exits: on the

right, left, and back. Remove the tab for the

exit you want to use by breaking it off with

your fingers. See the illustration on the right.

Note:

Once you remove a tab, you cannot replace it.

2. After removing the tab, also remove any protruding plastic, so

that the edge is smooth and does not damage the cables.

3. Position the two hooks on the connector cover so that they

hook the printer case, as shown on the left below.

4. Push the connector cover down to click onto the printer case.

To remove the connector cover, turn the printer over, insert a

flathead screwdriver under one hook, and pry up the hook while

lifting the connector cover. See the illustration on the right below.

Repeat this step for the other side.

Note:

Be careful not to damage the cables with the screwdriver.

hook

bottom of

the printer

screwdriver

TM-T88III User’s Manual 5

English

Installing the Paper Roll

1. Press the button, as shown on the left below, to open the cover.

2. Remove any used paper roll core, and insert the paper roll as

shown in the center below.

3. The correct direction of the paper is shown on the right below.

4. Pull out some paper, as shown on the left below, close the

cover, and tear off the paper, as shown on the right below.

Troubleshooting

No lights on the control panel

Check the power supply cable connections and the power outlet.

ERROR light on (not flashing) with no printing

If PAPER OUT is on, the paper roll is not installed or is near the end.

If PAPER OUT is off, the printer cover is not closed properly.

ERROR light flashing with no printing (and no paper jam)

Printing stops if the head overheats and resumes when it cools.

Turn the printer off, and after 10 seconds, back on.

ERROR

POWER

PAPER

OUT

FEED

ERROR

POWER

PAPER

OUT

FEED

ERROR

POWER

PAPER

OUT

FEED

ERROR

POWER

PAPER

OUT

FEED

6TM-T88III User’s Manual

English

Removing Jammed Paper

CAUTION:

Do not touch the print head because it can be very hot after printing.

1. Turn the printer off and press the cover open button.

2. Remove jammed paper, reinstall the roll, and close the cover.

3. If paper is caught in the cutter and you cannot open the printer

cover, open the cutter cover as shown on the left below.

4. Turn the knob until you see a triangle in the opening, as shown

on the right below. This returns the cutter blade to the normal

position. There is a label near the cutter to assist you.

5. Close the cutter cover.

6. Open the printer cover and remove the jammed paper.

Cleaning the Print Head

CAUTION:

After printing, the print head can be very hot. Be careful not to touch it

and to let it cool before you clean it. Do not damage the print head by

touching it with your fingers or any hard object.

Turn off the printer, open the paper roll cover, and clean the

thermal elements of the print head with a cotton swab moistened

with an alcohol solvent (ethanol, methanol, or IPA).

EPSON recommends cleaning the thermal head periodically

(generally every 3 months) to maintain receipt print quality.

ERROR

POWER

PAPER

OUT

FEED

ERROR

POWER

PAPER

OUT

FEED

ADJUSTMENT:

TURN KNOB

UNTIL YOU SEE

TRIANGLE IN OPENING

TM-T88III User’s Manual 7

English

lps: lines per second dpi: dots per 25.4 mm (dots per inch)

TM-T88III Specifications

Printing method Thermal line printing

Dot density 180 dpi × 180 dpi [dots per 25.4 mm {1"}]

Printing direction Unidirectional with friction feed

Printing width 72 mm {2.83"}, 512 dot positions

Characters per line

(default)

Font A: 42; Font B: 56

Character spacing

(default)

Font A: 0.28 mm {.01"} (2 dots); Font B: 0.28 mm {.01"} (2 dots)

Character size Standard/Double-height/Double-width/Double-width and Double-height

Font A: 1.41 ×3.39 mm/1.41 ×6.77 mm/2.82 ×3.39 mm/2.82 ×6.77 mm

Font B: 0.99 ×2.40 mm/0.99 ×4.80 mm/1.98 ×2.40 mm/1.98 ×4.80 mm

Number of characters Alphanumeric characters: 95; International characters: 37

Extended graphics: 128 × 11 pages (including one space page)

Print speed High-speed:

Approx. 150 mm/s {5.9"/s} max.; 47.2 lps, max. (3.18 mm {1/8"} feed); 35.5

lps, max. (4.23 mm {1/6"} feed, at 24 V, 28°C {82°F}, density level 1).

Speed is adjusted automatically depending on the voltage applied and

head temperature.

Low-power: Approx. 16.5 lps (4.23 mm feed {1/6"}); 70 mm/s {2.76"/s}

Ladder bar code: Approx. 42 mm/s {approx. 1.7"/s}

Paper feed speed Approx. 150 mm/s {approx. 5.9"/s} continuous paper feed

Line spacing (default) 4.23 mm {1/6"}

Character structure Font A: 12 ×24; Font B: 9 ×17 (including 2-dot horizontal spacing)

Font A is the default.

Paper roll (single-ply) Size: Width: 79.5 mm ± 0.5 mm {3.13" ± 0.02"}

Maximum outside diameter: 83 mm {3.26"}

Paper roll spool diameter: Inside: 12 mm {0.47"}; Outside: 18 mm {0.71"}

Thermal paper type Specified: Nakagawa Seisakujo, NTP080-80

(Original: Nippon Paper Industries Co., Ltd.,TF50KS-E)

Packaged paper roll: original: Oji Paper Mfg. Co., Ltd., PD160R

Interface

(compatible)

RS-232C/Bi-directional parallel

Dealer option: RS-485, USB, 10 Base T I/F

Receive buffer 4KB/45 bytes

DKD Function 2 drives

Power supply + 24 VDC ± 7%

Current consumption

(at 24V)

High-speed mode: Mean: Approx. 1.8A Peak: Approximately 7.7A

Low-power mode: Mean: Approx. 1.2A Peak: Approximately 6.6A

Life Mechanism: 15,000,000 lines

Thermal head: 100 million pulses, 100 km

Autocutter: 1,500,000 cuts

MTBF 360,000 hours

MCBF 52,000,000 lines

(Average failure interval based on failures relating to wearout and random

failures up to the life of 15 million lines.)

Temperature Operating: 5 to 45°C {41 to 113°F}

Storage: –10 to 50°C {14 to 122°F}, except for paper

Humidity Operating: 10 to 90% RH

Storage: 10 to 90% RH, except for paper

Overall dimensions 148 ×145 ×195 mm {5.83 ×5.71 ×7.68"} (H ×W ×D)

Weight (mass) Approximately 1.8 kg {3.96 lb}

8 TM-T88Ⅲユーザーズマニュアル

日本語

TM-T88III

ユーザーズマニュアル

イラスト

本書は言語別の４部構成となっています。イラストは第１部の英語版のみ掲載されておりますのでそちらを

ご覧ください。それぞれのイラストが掲載されているページ番号は本文中に記載されています。

下記に示す部品名称につきましては、表紙の裏のイラストをご覧ください。

部品名称

1. プリンタカバー

2. カッタカバー

3. カバーオープンボタン

4. コントロールパネル

ご注意

(1) 本書の内容の一部または全部を無断で転載、複写、複製、改ざんすることは固くお断りします。

(2) 本書の内容については、予告なしに変更することがあります。

(3) 本書の内容については、万全を期して作成いたしましたが、万一ご不審な点や誤り、記載もれなど、お

気づきの点がありましたらご連絡ください。

(4) 運用した結果の影響については、上項にかかわらず責任を負いかねますのでご了承ください。

(5) 本製品がお客様により不適切に使用されたり、本書の内容に従わずに取り扱われたり、またはエプソン

およびエプソン指定の者以外の第三者により修理･変更されたことなどに起因して生じた損害などにつ

きましては、責任を負いかねますのでご了承ください。

(6) エプソン純正品およびエプソン品質認定品以外のオプションまたは消耗品を装着してトラブルが発生

した場合には、責任を負いかねますのでご了承ください。

EPSON®はセイコーエプソン株式会社の登録商標です。

ESC/POS®はセイコーエプソン株式会社の登録商標です。

Andere Handbücher für TM-T88III series

Inhaltsverzeichnis

Andere Epson Drucker Handbücher

Epson

Epson Stylus Pro 7890 Series Bedienungsanleitung

Epson

Epson EC-01 Bedienungsanleitung

Epson

Epson TM-C3500 Series Bedienungsanleitung

Epson

Epson PowerLite 7000 Stücklistenhandbuch

Epson

Epson AcuLaser 2600N Review Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Epson

Epson WF-7620 Series Bedienungsanleitung

Epson

Epson SureColor SC-F9330 Series Bedienungsanleitung

Epson

Epson PictureMate PM-401 Bedienungsanleitung

Epson

Epson Stylus Photo 780 Bedienungsanleitung

Epson

Epson ET-2400 Bedienungsanleitung

Epson

Epson ET-M2120 Series Bedienungsanleitung

Epson

Epson Stylus COLOR 860 Bedienungsanleitung

Epson

Epson LQ-860 - Impact Printer Bedienungsanleitung

Epson

Epson FX-880 - Impact Printer Bedienungsanleitung

Epson

Epson TM-U950P - B/W Dot-matrix Printer Bedienungsanleitung

Epson

Epson Stylus Color 670 Bedienungsanleitung

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Epson

Epson Stylus Color 800N Bedienungsanleitung

Epson

Epson Stylus Photo 820 Bedienungsanleitung

Epson

Epson TM-U220-i Bedienungsanleitung

Epson

Epson 3800 - Stylus Pro Color Inkjet Printer Bedienungsanleitung

Epson

Epson SP7700VM Bedienungsanleitung

Epson

Epson Stylus Photo PX820FWD Benutzerhandbuch

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung