Epson 730c - PowerLite Projector Abmessungen

Page 1 of 1

EPSON PRODUCT SUPPORT BULLETIN

Date: 8/30/2007 Originator: DS

PSB #: PSB.2007.08.001 Authorization:

Reference: N/A Total Pages: 1

Product(s): Epson Projectors with an HD-15 VGA Analog/Component Input

Subject: Elmo HV-110XG Document Camera and Projector Compatibility

This bulletin was created to inform you of an operational issue with the Elmo HV-110XG

Document Camera when initially connected to an Epson projector.

Problem:

When attempting to use the Elmo HV-110XG Document Camera connected via the VGA HD15

connection to display content from its document bed. When connected to the projector, the

projector displays only the Blue Screen - No Signal message and will blink off and on or

display just the Blue Screen - No Signal message. When a computer is connected to the Elmo

HV-110XG Document Camera and switched to Pass-Through mode, the computer image is

displayed correctly by the projector. When switching back to the document table source of the

Elmo HV-110XG Document Camera, the problem returns. The Elmo HV-110XG Document

Camera puts out a Progressive Scan 20fps signal to the projector's VGA Analog port. This

signal is detected at 15 kHz Vertical and 291.8 kHz Horizontal frequencies which are beyond

projector sync specifications.

Solution:

With the Elmo HV-110XG Document Camera powered on and connected to the projector via

the VGA computer cable, access the Computer1/Computer2 setting in the projector menu

system and select the Component setting within the appropriate connection. This will allow

the Elmo HV-110XG Document Camera and projector to sync and the projector to display the

image of the document camera bed and its contents. However, the image will have a pink

cast. To eliminate the pink cast, change the projector setting from Component to RGB then to

Auto and exit from the menu. The projected image will now look normal. This will now allow

the Elmo HV-110XG Document Camera to sync and display the image properly to any other

connected Epson projector without having to change the projector settings.

Page 1 of 14

PSB.2004.10.002

EPSON PRODUCT SUPPORT BULLETIN

Date: 10/08/2004 Originator: DS

PSB #: PSB.2004.10.002 Authorization:

Reference: TI 04-46e Rev. A Total Pages: 14

Product(s): EMP NS Connection, EMP Network Manager, EMP Monitor,

EMP Multi Screen Adjustment, Cinema Color Editor, VCOM Driver

Subject: Evaluation results of Epson Projector PC applications tested in Windows XP

with SP2.

The purpose of this bulletin is to provide information on Epson PC projector applications tested

under the Windows XP SP2 (Service Pack2) environment.

Description:

Information is provided about the evaluation results and recommendations for Epson PC

projector applications functionality in Windows XP SP2 Firewall environment.

Reason:

Compatibility testing for functionality of EMP NS Connection, EMP Network Manager, EMP

Monitor, EMP Multi Screen Adjustment, Cinema Color Editor, VCOM Driver in the Windows

XP SP2 environment.

Results of Windows XP SP2 installation:

Installing SP2 on PCs did not disturb the installation of the above software applications.

Also, the application software can be installed on PCs where SP2 or earlier versions are

installed without any issues.

The information contained in the following pages provides details for executing the

applications in Windows XP SP2.

Page 2 of 14

PSB.2004.10.002

Executing the Software:

When executing the software noted below for the first time after SP2 installation completes,

the following security alert messages are displayed:

[EMP NS Connection]

Security alert screen (EMP NS Connection)

[EMP Network Manager]

Security alert screen (EMP Network Manager)

Page 3 of 14

PSB.2004.10.002

[EMP Monitor]

Security alert screen (EMP Monitor)

[EMP Multi Screen Adjustment]

Security alert screen (EMP Multi Screen Adjustment)

The Security Alert screen for EMP Multi Screen Adjustment is shown after clicking the

Auto button of Network or clicking the Add button after entering an IP address in the

IP Address box.

Page 4 of 14

PSB.2004.10.002

[Cinema Color Editor]

Security alert screen (Cinema Color Editor)

The functions of the three buttons displayed in the security alert screen are explained

below.

[Keep Blocking] --- Enables you to register a started application in the “Exceptions”

program of the Windows Firewall. The network port that the

application uses is blocked. By selecting this button once, this

security alert message will not be shown when starting the

application next time.

[Unblock] ------------- Enables you to register a started application in the “Exceptions”

program of the Windows Firewall and unblock the network port that

the application uses. By selecting this option once, this security alert

message will not be shown when starting the application next time.

[Ask me later]-------- When you want to select both buttons above or select either one

later, this button is selected. The started application is not registered

in the “Exceptions” program of the Windows Firewall and the

network that the application uses is not unblocked. However, when

restarting the application, the same security alert message is shown.

•PC applications will work normally on Windows XP with SP2 if the “Unblock

Item” is selected when the security alert screen is shown.

For the detail operation information of each application, please refer to the following:

Page 5 of 14

PSB.2004.10.002

Operating Status Report

When selecting the Keep Blocking button, the security alert message is closed and the

main screen of each application is displayed.

[EMP NS Connection Application]

Port 3620 is necessary for searching for projectors. If this port is blocked, projectors are not

detected.

The other applications operate normally. However, there is a case that execution of

automatic search disables automatic detection. This occurs when projectors are registered

for automatic detection in EMP Monitor before installing SP2, then the registered projectors

may not be detected again after SP2 installation. Therefore it is recommended to select

Unblock in the security alert screen.

If “Keep Blocking” has been selected when starting the application for the first

time, and the blocking needs to be removed, complete the execution of the application and

proceed with unblocking as follows:

a.) Start the Windows Security Center. Double click the icon in the shape of a shield that

is always displayed on the taskbar after the installation of SP2.

Windows Security Center screen

b.) Select and start Windows Firewall

Page 6 of 14

PSB.2004.10.002

Windows Firewall screen

[Caution]

In case the check box

for Don’t allow

exceptions

is checked (this box is

not checked at the

initial setting), a

network port for

software is not

unblocked even though

the software is checked

on Exceptions.

Make sure this option is

not selected.

Page 7 of 14

PSB.2004.10.002

c.) Select the Exceptions tab and display exceptions program.

•Exceptions screen

d.) Check the check boxes for the software you don’t want to block.

[Caution]

If this check box is

not checked, the

security alert

screen is not

displayed when

starting software.

Page 8 of 14

PSB.2004.10.002

[EMP NS Connection] •Check EasyMP Software box

Unblock screen (EMP NS Connection)

Page 9 of 14

PSB.2004.10.002

[EMP Network Manager Application]•Check EPSON Projector box

Unblock screen (EMP Network Manager)

Andere Handbücher für 730c - PowerLite Projector

Dieses Handbuch passt für folgende Modelle

Andere Epson Projektor Handbücher

Epson

Epson EF-100WATV Bedienungsanleitung

Epson

Epson ELPMB29 Bedienungsanleitung

Epson

Epson Elp-3000 Bedienungsanleitung

Epson

Epson EB-Z8455WU Bedienungsanleitung

Epson

Epson EMP-S4 Bedienungsanleitung

Epson

Epson PowerLite TW-100 Bedienungsanleitung

Epson

Epson 1925W - POWERLITE Multimedia Projector Referenzhandbuch

Epson

Epson V11H071920 - PowerLite 9300i SXGA+ LCD... Abmessungen

Epson

Epson PowerLite 9300i Technisches Datenblatt

Epson

Epson PowerLite Cinema 200 Bedienungsanleitung

Epson

Epson 755c - PowerLite XGA LCD Projector Technisches Datenblatt

Epson

Epson Home Cinema 4000 Technisches Datenblatt

Epson

Epson PowerLite Home Cinema 1450 Technisches Datenblatt

Epson

Epson POWERLITE HOME 10+ CPD-1790-4R2 Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 710HD Technisches Datenblatt

Epson

Epson PowerLite 750c Bedienungsanleitung

Epson

Epson EMP-8000 - XGA LCD Projector Bedienungsanleitung

Epson

Epson MovieMate 60 Bedienungsanleitung

Epson

Epson PowerLite 700 Bedienungsanleitung

Epson

Epson dreamio EMP-TW2000 Bedienungsanleitung

Epson

Epson BrightLink 475Wi Bedienungsanleitung

Epson

Epson PowerLite 5500c Bedienungsanleitung

Epson

Epson EB-L20002U Bedienungsanleitung

Epson

Epson BrightLink Pro 1470Ui Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Bedienungsanleitung

JVC

JVC 1108TTH-AO-AO Bedienungsanleitung