Epson EMP-800 / 810 Bedienungsanleitung
WARNING Never look into the lens while
the projector's power is turned on.
Be sure to read the User,s Guide thoroughly before using this projector.
QUICK REFERENCE GUIDE
Setting Up Adjust the distance between the projector and
the screen until the desired image size is obtained.
* When installing to wall, leave a space of about
7.87 inches (0.2m) between the projector and the wall.
Page 18 of User's Guide screen size
projection distance
Connections Connecting to a Computer
Connecting to aVideo Source
* Turn off the power for both the projector and the other equipment before connecting them.
Computer cable (accessory)
A/V cable (accessory)
To computer's
monitor port
(video port)
To video output connector (yellow)
To audio output L connector (white)
To audio output R connector (red)
Video connector (yellow)
Audio R connector (red)
Audio L connector (white)
You may need to use an optional
adapter or purchase a separate adapter
to connect the computer to the projector,
depending on the shape of the
computer's monitor port.
If connecting component video source
(such as a DVD player), you can use the
optional component video cable to
connect the source to the Computer
2/Component Video connector at the
rear of the projector.
Computer 2/Component Video connector
Pages 19--34 of User's Guide
Tip
Setting Up /
Connections
Projecting Remove the lens cover.
Connect the power cord to the projector.
Turn on the power for the
input source.
In the case of a VCR, press the PLAY button.
Press the button to turn on the
projector's power.
Connect the power cord to an electrical outlet.
If using the remote control, set
the R/C switch to the ON
position and then press the
button.
will start flashing green and
projection will start.
(Warm-up in progress)
The indicator will light orange.
Operation
indicator
Pages 36--38 of User's Guide
If images do not appear ...
If you have other problems ...
If a laptop computer or a computer with a
LCD screen has been connected to the
projector, you may need to change the
output destination for video signals
depending on the computer keys ( or
) or the computer's settings.The
output destination can normally be
changed by holding down the computer's
key and pressing one of the
Function keys.
Once the source has been changed, after
a short wait the projector will start
projecting. If the output has been
changed to external output, only the
external output should be used.
For details, refer to the documentation
provided with your computer.
Change the input
signal.
Refer to the online
Help information.
After restarting the computer,
change the Control Panel
monitor and sound settings
so that Mirroring is active.
* Refer toTroubleshooting.
Projector Remote Control
Projector Remote Control
Tip
Press , and
then follow the
instructions.
Examples of changing output
NEC
Panasonic
TOSHIBA
IBM
SONY
FUJITSU
Macintosh
Projecting
Adjustment Adjusting the projection angle
Adjusting the image size and focus
Front adjustable foot Foot adjust button
Focus adjustment
Image size adjustment
See page 7.
If you change the projection angle, you
may get keystone distortion in the
images.You can use the , ,
and buttons on the projector's
control panel to correct keystone
distortion.
You can adjust the amount of extension for the front adjustable foot to adjust the projection angle.
The angle can be adjusted horizontally within a range of approximately 10°.
Turn to Wide to increase the size
Turn to Tele to reduce the size
Tip
Pages 41,42, 43 and 46 of
User's Guide
Automatically adjusting computer images to the
optimum settings
Press on the projector's control panel or on the remote control.The tracking,
display position and synchronization will be automatically adjusted.
Other adjustments
Press on the projector's control panel or on the remote control.The setting menu will be displayed on
the projection screen, and you can then adjust settings such as brightness, contrast and sharpness.
Projector Remote Control
Using the on-screen menus
Projector Remote Control
Main menu Projector Remote control
Move up
Move down
Move
right
Return
Return
Move
left
Select
Select
Move
down Move
right
Move
left
Move
up
Adjustment /
Turning Off the Projector
Adjustment
If the images have keystone distortion ...
Press on the projector's control panel to correct the keystone distortion.
If using both horizontal and vertical keystone correction,
carry out in the following order.
1 .With the front adjustable foot retracted, set the projector so that it is fully horizontal.
2 . Extend the front adjustable foot to adjust the angle as necessary.
3 . Adjust the vertical keystone distortion until both sides of the picture are vertical.
4 . Adjust the horizontal keystone distortion until the top and bottom edges of the picture are both horizontal.
Correcting keystone distortion
Pages 44 and 45 of User's Guide
When keystone correction is carried
out, the projected image will become
smaller.
The keystone correction settings are
memorized, so that if you change the
position or angle of the projector, you may
need to readjust the keystone correction
settings.
To return an altered keystone correction
setting to the factory default setting, do
the following.
To restore the vertical keystone correction
to the default setting:While holding down
the button, press the button for
1 second or more.
To restore the horizontal keystone
correction to the default setting:While
holding down the button, press the
button for 1 second or more.
If the images become uneven in
appearance after keystone correction is
carried out, decrease the Sharpness
setting.
Correction in
vertical direction
Correction in
horizontal direction
Tip
Turning Off
the Projector
Press the button twice to turn off the
projector's power.
Turn off the power for the equipment connected
to the projector.
Check that is lit steadily with an orange color,
and then disconnect the power cord.
If the power cord is disconnected while is still flashing orange, it may cause problems with
projector operation.
will start flashing orange. (Cool-down in progress/approx.2 minutes)
* Set the R/C switch on the remote control to the OFF position.
Operation indicator
Pages 39 and 40 of
User's Guide
Adjustment /
Turning Off the Projector
Functions for
Enhancing Projection
Using the remote control for one-person presentations
The remote control can be used to carry out the same functions as left-clicking and right-clicking mouse buttons
on a computer.You can use the remote control to control the computer's mouse pointer from a distance.
When using the remote control as a
wireless mouse, you need to connect
the projector as follows.
Use a USB cable to connect the
projector to the USB port of a
computer.
If the mouse function does not work
after connecting a PS/2 mouse, you
will need to restart the computer.
Use only the accessory mouse
cable provided, otherwise the
wireless mouse function may not
operate correctly.
Mouse pointer movement
Tilt the button in the direction you want
the mouse pointer to go.
Mouse clicks
Mouse/USB port
Mouse/USB connector
Mouse cable
(accessory)
This projector is equipped with a variety of useful functions
for enhancing projection.
Refer to the corresponding pages of the User's Guide for
details on each function.
Wireless mouse function
Page 25 of User's Guide
For left clicks: Press [Left] For right clicks:Press [Right/Esc]
Tip
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Epson Projektor Handbücher
Epson
Epson PowerLite Cinema 500 Bedienungsanleitung
Epson
Epson EX70 Bedienungsanleitung
Epson
Epson EB-1925W Bedienungsanleitung
Epson
Epson VS410 Bedienungsanleitung
Epson
Epson PowerLite Pro G5150NL Bedienungsanleitung
Epson
Epson V11H319220 - MovieMate 60 LCD Projector Bedienungsanleitung
Epson
Epson VS400 Referenzhandbuch
Epson
Epson PowerLite Home Cinema 8345 Bedienungsanleitung
Epson
Epson PowerLite Pro Z8050WNL Bedienungsanleitung
Epson
Epson VS410 Referenzhandbuch
Epson
Epson Home Cinema 5050UB Technisches Datenblatt
Epson
Epson Dreamino EMP-TW20 Bedienungsanleitung
Epson
Epson EB-1460Ui Bedienungsanleitung
Epson
Epson EH-TW8000 Bedienungsanleitung
Epson
Epson EX3220 Bedienungsanleitung
Epson
Epson EX21 Referenzhandbuch
Epson
Epson EB-1830 Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 800 HQV HQV video... Bedienungsanleitung
Epson
Epson V11H283020 Bedienungsanleitung
Epson
Epson 410W - PowerLite WXGA LCD Projector Technisches Datenblatt
Beliebte Projektor Handbücher anderer Marken
iEmmet
iEmmet MP-312 Bedienungsanleitung
Sony
Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung
Sony
Sony VPL-HW65ES Service-Handbuch
Toshiba
Toshiba TLP-791U Bedienungsanleitung
Philips
Philips LC1341 Referenzhandbuch
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
