Epson PowerLite Home Cinema 1080 Montageanleitung

Follow these instructions to set up the PowerLite Pro Cinema 1080

projector and HQV video processor.

For more information, see the manuals that came with these products.

Installer Guide

Setting Up the Equipment and Displaying an Image

1. Unpack the HQV video processor and attach the serial number sticker included with it to

the HQV User Manual.

2. Connect at least one video source to the video processor.

3. Connect an HDMI cable from the video processor to the projector.

4. Plug in the power cord for the video processor. Make sure batteries are installed in the

HQV remote control.

5. Set up the projector and turn it on as outlined below. For details, see the projector User’s

Guide.

■Remove the protective lens pad from the projector, then remove the lens cap.

■Make sure batteries are installed in the Epson remote control.

■Plug in the power cord, then turn on the power switch on the back of the projector.

Once the projector is receiving power, press the On button on the Epson remote

control to turn it on.

6. Press the Pattern button on the Epson remote control, then adjust the image as outlined

below.

■Focus and zoom the image.

■Position the image on the screen. If possible, keep the projector level and position the

image using only the lens shift dials.

Caution: Do not try to move the lens by hand, or you may damage the projector. Always

use the lens shift dials to change the lens position.

HDMI OUT

Video processor

Projector

When done, press the Pattern button to clear the displayed pattern.

Note: If the projector is ceiling-mounted or set up for rear-screen projection, you’ll use the

projector’s menu system to reorient the image (see step 1 on page 4). For best image quality,

avoid tilting the projector or angling it toward the screen.

7. Press the HDMI button on the remote control to select HDMI as the input source.

8. Turn on the power switch on the back of the HQV video processor (above the AC power

inlet). It may take several seconds for the video processor to come on.

9. Press the ON/SETUP button on the HQV remote control to place the video processor in

Setup mode. (You see SetUp Mode on the display.)

Note: If the HQV video processor doesn’t respond to the remote control, check the remote

control’s batteries. If the batteries are good, turn off the HQV video processor and then turn it

back on using the power switch above the AC power inlet.

Press the MENU button. Then use the uand dbuttons to select the output

resolution setting (“Output = xxx”). Use the land rbuttons to change the setting

to Output = 1080p 60Hz.

Press the ON/SETUP button on the remote control to exit Setup mode.

10. Make sure the projector is displaying an image. If not, turn on a connected video source

and select it by pressing the appropriate source button on the HQV remote control.

HDMI

button

Selecting Projector Settings

1. If the projector is ceiling-mounted or set up for rear-screen projection, you need to

reorient the image. Press the Menu button on the Epson remote control and open the

Settings menu. Select Projection and then select the projector’s mounting position.

Press the Menu button when done to exit the menu system.

2. Press the Aspect button and select Normal as the aspect ratio.

3. Press the Color Mode button and select HD as the color mode.

Note: This sets the brightness, contrast, and color settings to 0, Skin Tone to 3, Absolute Color

Temperature to 7500K, lamp Brightness Control to High, and Auto Iris to Off.

4. Press the Gamma button and select 2.2 as the gamma setting.

5. Press the Menu button, open the Image menu, and select Sharpness.

If you see this screen, highlight Standard and press the Select button:

Change the Sharpness setting to -3.

6. Press the ESC button to return to the main menu. Open the Signal menu and then

adjust the following settings:

■Set Output Scaling to 100%.

■Set EPSON Super White to Off.

■Set HDMI Video Range to Normal.

7. Press the Menu button when done to exit the menu system.

If you see this screen,

select Standard

Selecting HQV Video Processor Settings

1. Press the MENU button on the HQV remote control.

2. In the Picture menu, select Aspect Ratio and set it to Full Screen.

Note: If Full Screen is not a selectable option, select the Standard setting instead. If the video

source is playing a high-definition video, you won’t be able to adjust this setting. You can play a

starndard-definition DVD or switch to a different input, such as S-video, to adjust this setting for

other sources.

3. In the Advanced menu, select HQV Film Mode and set it to Auto.

4. Make any additional desired adjustments, following the instructions in the HQV

User Manual. For example, you may want to select appropriate noise reduction settings.

Performing Color Calibrations

Use the HQV calibration software to perform final color calibrations. See the ISF Certified

Calibration Controls Dealer Guide for details. Once the ISF calibrations are complete, you can

use the projector’s menu system, if necessary, to further fine-tune the color settings.

Installing the Calibration Software and USB Drivers

Note: These instructions explain how to connect to the HQV processor using a USB cable. To

connect using a serial or network cable, see the ISF Certified Calibration Controls Dealer Guide.

1. Insert the HQV Video Processor TX3 CD in your Windows XP or 2000 computer.

Locate the setup.exe file and double-click it to start the installation. Follow the

on-screen instructions to install the calibration software.

Leave the CD in your CD/DVD drive when done.

2. Connect a USB cable from your computer to the USB port on the HQV video processor.

You should see a Found New Hardware wizard on your computer screen. If not, make

sure the video processor is turned on.

Follow the steps below to install drivers from the calibration software CD.

3. Windows XP: At the Found New Hardware screen, select No, not this time and click

Next.

Windows 2000: Click Next.

4. Windows XP: At the next page, select Install from a list or specific location and click

Next. Then select Search for the best drivers in these locations. Make sure the

checkbox for Search removable media is selected.

Windows 2000: Select Search for a suitable driver for my device. Click Next, then

select CD-ROM drives.

5. Click Next to install the driver, then click Finish when done.

6. You see the Found New Hardware screen again. Repeat steps 3 through 5 to install a

second driver.

7. Remove the CD from your CD/DVD drive.

Using the Calibration Software

Use the calibration software to adjust the ISF Day and Night settings for each connected

video source.

1. Launch the Config Tool located in the Silicon Optix program folder.

2. When the program opens, click the Connect button, select USB as the connection

method, and click OK.

3. Select either Day or Night, depending on the ISF configuration you want to

adjust.

4. Click the tab that corresponds to the video source you want to adjust.

5. For the Input Parameters, adjust the Contrast, Brightness, Color, Hue, and

Sharpness as needed.

6. If you want to eliminate overscan, reduce all four Overscan settings to 0 (left, right, top,

and bottom). If you want the image overscanned by about 2.5 to 3 percent, leave the

settings as they are.

7. For the Output Parameters, you need to make sure the Luma is set correctly for all digital

video sources to prevent clipping. Set the Peak to 235 and the Base to 16.

Note: RGB Peak and Base parameters should be adjusted, if necessary, only with photometric

equipment. See the HQV ISF Certified Calibration Controls Dealer Guide for details.

8. When you’re done making adjustments, click the Disconnect button to exit the

software.

Using the Projector’s Color Adjustments

If you notice that the peak of the red color channel is low after calibrating the component and

HDMI inputs, or if you need to make any other color adjustments, you can fine-tune the

color using the RGB and RGBCMY screens in the projector’s menu system.

Note: These adjustments should be made only by a trained technician with a reference meter such

as the Photo Research PR-650 SpectraColorimeter or Konica Minolta CS-200 Chroma Meter.

■RGB

Press the Menu button on the Epson remote control and access this screen by selecting

Image > Advanced > RGB.

Adjust the offset and gain for each signal color. Use Offset to adjust the base and Gain to

adjust the peak.

■RGBCMY

Press the Menu button on the Epson remote control and access this screen by selecting

Image > Advanced > RGBCMY.

Adjust the hue and saturation for each color component (red, green, blue, cyan, magenta,

yellow).

For your reference, the NTSC and HDTV color coordinate specifications are shown below.

Using IR and ESC/VP21 Command Codes

If you want to program a universal remote control to work with the projector, you can obtain

a list of projector IR control codes from the Epson web site at epson.com/support.

If you want the HQV video processor to be able to turn the projector on and off or control

other functions, connect the supplied null-modem RS-232 cable as shown below. See the

HQV User Manual and Programming and Service Manual for more information.

NTSC (SMPTE) HDTV (ATSC)

XY XY

Red 0.630 0.340 Red 0.640 0.330

Green 0.310 0.595 Green 0.300 0.600

Blue 0.155 0.070 Blue 0.150 0.060

Cyan 0.231 0.326 Cyan 0.225 0.329

Magenta 0.314 0.161 Magenta 0.321 0.154

Yellow 0.421 0.507 Yellow 0.419 0.505

Video processor

Projector

RS-232 (SLAVE)

You can download the complete ESC/VP21 Communication Manual for Epson home theater

projectors from the Epson web site at epson.com/support. Following are some of the available

codes:

Item Command

Power ON/OFF ON PWR ON

OFF PWR OFF

A/V Mute ON/OFF ON MUTE ON

OFF MUTE OFF

A/V Mute selection Black MSEL 00

Blue MSEL 01

Source

change

Terminal Signal name

Component Component video SOURCE 10

YCbCr SOURCE 14

YPbPr SOURCE 15

Auto SOURCE 1F

PC HDB15 SOURCE 20

RGB SOURCE 21

Input 3 (HDMI) HDMI SOURCE 30

Video Video/S-Video SOURCE 40

Video (RCA) SOURCE 41

S-Video SOURCE 42

Input 5 Digital video SOURCE C0

YCbCr SOURCE C4

YPbPr SOURCE C5

Auto SOURCE CF

Color Mode Cinema Night CMODE 05

Cinema Day CMODE 06

Natural CMODE 07

Vivid CMODE 08

HD CMODE 09

Silver Screen CMODE 0A

Aspect ratio Auto ASPECT 00

Normal ASPECT 20

Full ASPECT 21

Zoom ASPECT 22

Wide ASPECT 25

Item Command

Andere Handbücher für PowerLite Home Cinema 1080

Dieses Handbuch passt für folgende Modelle

Andere Epson Projektor Handbücher

Epson

Epson VS315W Bedienungs- und Sicherheitshinweise

Epson

Epson EMP 8200 Bedienungsanleitung

Epson

Epson EMP-7850 Bedienungsanleitung

Epson

Epson EB-G7905U Bedienungsanleitung

Epson

Epson 9000i - PowerLite SXGA LCD Projector Bedienungsanleitung

Epson

Epson EasyMP EMP-735 Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 5030UB Bedienungsanleitung

Epson

Epson PowerLite 71c Bedienungsanleitung

Epson

Epson CO-W01 Bedienungsanleitung

Epson

Epson EB-420 guide Bedienungsanleitung

Epson

Epson EB-84L Bedienungsanleitung

Epson

Epson EB-X92 Bedienungsanleitung

Epson

Epson EF12 Bedienungsanleitung

Epson

Epson PowerLite 1751 Technisches Datenblatt

Epson

Epson PowerLite 7000 Bedienungsanleitung

Epson

Epson 410W - PowerLite WXGA LCD Projector Referenzhandbuch

Epson

Epson PowerLite Home Cinema 500 Stücklistenhandbuch

Epson

Epson PowerLite 732c Bedienungsanleitung

Epson

Epson PowerLite 955W Referenzhandbuch

Epson

Epson EB-Z8000WUNL Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 3020plus Bedienungsanleitung

Epson

Epson PowerLite 7000XB Bedienungsanleitung

Epson

Epson LS300BATV Bedienungsanleitung

Epson

Epson Artisan 810 Series Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Bedienungsanleitung

JVC

JVC 1108TTH-AO-AO Bedienungsanleitung