Equinox Systems Power Par 54 MKII Bedienungsanleitung

Order code: EQLED114

Power Par 54 MKII

User Manual

www.prolight.co.uk Power Par 54 MKII User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 100~240V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is

not designed for or suitable for household use. The

product must be installed by a qualied technician in

accordance with local territory regulations. The safety of

the installation is the responsibility of the installer. The

xture presents risks of severe injury or death due to re

hazards, electric shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk Power Par 54 MKII User Manual 3

01 - Hanging bracket

02 - Hanging bracket

adjustment knob

03 - LED display

04 - Function buttons

05 - IEC power input

06 - IEC power output

07 - Fuse: F3A 250V

08 - 3-Pin DMX input

09 - 3-Pin DMX output

10 - Fan

In the box:

1 x xture,

1 x power cable

& 1 x user manual

Product overview & technical specications

The Power Par 54 MKII is a powerful xture that feature tri-colour LEDs and produce a range of effects including

colour change and fade, controllable in auto and sound active modes along with DMX. A dual bracket is included

allowing the xture to be hung or stood on the oor.

• 54 x 3W tri-colour

LEDs (RGB)

• Beam angle: 25°

• 1721 Lux @ 2m (full on)

• DMX channels: 6

• Auto, sound active and

master/slave modes

• 0-100% dimming and

variable strobe

• 4 push button menu with

LED display

• Bracket allows for multiple

rigging

or oor standing

applications

• IEC power input/output

• 3-Pin XLR input/output

• Fan cooled

Power Par 54 MKII

POWER CONSUMPTION: 165W

POWER PAR 54 MKII

www.prolight.co.uk

FUSE: F3A 250V

Specications Power Par 54 MKII

Power consumption 165W

Power supply 100~240V, 50/60Hz

Fuse F3A 250V

Dimensions 285 x 266 x 94mm

Weight 1.5kg

Order codes EQLED114

0m 1m 2m 3m 4m 5m

25° - Lux

FULL ON

6884

4436

9768

2052

1721

1109

2442

513

764

492

1085

228

25°

430

277

610

128

275

177

390

235mm 28mm

266mm 94mm

235mm

285mm

www.prolight.co.uk Power Par 54 MKII User Manual 4

Operating instructions

DMX mode:

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of the

xture and each xture independently.

To access the DMX address mode, press the “MENU” button on the front of the unit to show A001

on the LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the

required DMX address. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

RGB colour mix mode:

In this mode you can set the xture to any colour and any brightness.

To access the colour mix mode press “MENU” until the display shows Pr-- on the LED display.

Press the “ENTER” button and use the “UP” and “DOWN” buttons to select Pr00.

Press the “ENTER” button to show r--- with 3 digits after on the LED display.

Press the “ENTER” button to conrm.

The rrepresents red, G= green and b= blue.

The 3 digits after are the brightness setting from 000 ~ 255.

For example:

If you set r, G, ball to zero, your unit will have no LEDs lit up (blackout).

If you set r000 to r255 and Gand bto zero, your unit will show only red LEDs.

Press the “ENTER” button to conrm the setting and move to the next colour.

To exit out of any of the above options, press the “MENU” button.

6 channel mode:

Channel Value Function

CH1 000-255 Red dimmer (0-100%)

CH2 000-255 Green dimmer (0-100%)

CH3 000-255 Blue dimmer (0-100%)

CH4

000-027 No function

028-055 Strobe (use CH6 for speed)

056-083 Strobe with colour change

(use CH6 for speed)

084-111 Red

112-139 Green

140-167 Blue

168-195 Yellow

196-223 Purple

224-251 Cyan

252-255 White

CH5

000 No function

001-012 Red fade in/out

(use CH6

for speed)

013-025 Green fade in/out

026-038 Blue fade in/out

039-051 Yellow fade in/out

052-064 Purple fade in/out

065-077 Cyan fade in/out

078-090 White fade in/out

091-116 Auto colour fade in/out

117-142 Colour fade

143-168 Colour change

169-181 Colour change with strobe

182-207 All auto shows

208-255 Sound active ash (when CH6 is 000)

208-255 Sound active (when CH6 is 001-255)

CH6 000-255 Speed (slow-fast)/Sensitivity (low-high)

www.prolight.co.uk Power Par 54 MKII User Manual 5

Built-in program mode:

To access built-in program mode press “MENU” until the display shows Pr-- on the LED display.

Press the “ENTER” button and use the “UP” and “DOWN” buttons to select between Pr00 ~ Pr13.

Press the “ENTER” button and use the “UP” and “DOWN” buttons to select the speed between

SP00 ~ Sp20. Press the “ENTER” button to conrm.

To exit out of any of the above options, press the “MENU” button.

Sound active mode:

To access the sound active mode, press the “MENU” button on the front of the unit to show Soud on

the LED display. Now press the “ENTER” button and the display will show Sens. Press the “ENTER”

button again and use the “UP” and “DOWN” buttons to select the sensitivity level from 000-100.

Press the “ENTER” button to conrm the setting.

Value: 000 - 100 (000 = low,100 = high)

To exit out of any of the above options, press the “MENU” button.

Master/slave mode:

To set the master unit, press the “MENU” button on the rear of the master unit to select your

desired program (sound active or RGB colour mix).

To set the other units in slave mode, press the “MENU” button on the rear of the unit to show SLav

on the LED display and press the “ENTER” button to conrm the setting. The units will now run in

sequence with the master unit.

To exit out of any of the above options, press the “MENU” button.

Built-in program mode

Pr00 - Pr13

Pr00 - RGB colour mix mode

r000~r255 R

G000~G255 G

b000~b255 B

Pr01 - R

Pr02 - G

Pr03 - B

pr04 - RG

Pr05 - RB

Pr06 - GB

Pr07 - RGB

Pr08 - Colour fade in-out (3 colours)

Pr09 - Colour fade in-out (7 colours)

Pr10 - Colour fade

Pr11 - Colour fade in-out (7 colours) & colour fade

Pr12 - Colour change (3 colours)

Pr13 - Colour change (7 colours)

Slave mode SLAV

Sound active mode SOUd

Sens

000~ 100

DMX mode 6CH

Address setting A001~A512

Menu system

www.prolight.co.uk Power Par 54 MKII User Manual 6

Setting the DMX address:

The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”

from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel

indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was

addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104,

105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in

the chain starts at 107.

DMX 512:

DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.

DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”

XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).

DMX linking:

DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest

cable path possible. The order in which xtures are connected in a DMX line does not inuence the

DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in

a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a

DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,

no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):

This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.

Your unit requires either a standard 3-pin or 5-pin XLR connector for data input/output,

see images below.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight Concepts dealers.

Please quote: CABL10 – 2m CABL11 – 5m CABL12 – 10m3-Pin:

CABL185 – 2m CABL187 – 5m CABL188 – 10m5-Pin:

www.prolight.co.uk Power Par 54 MKII User Manual 7

Notice:

Be sure to follow the diagrams below when making your own cables.

Do not connect the cables shield conductor to the ground lug or

allow the shield conductor to come in contact with the XLRs

outer casing. Grounding the shield could cause a short circuit

and erratic behaviour.

Line termination:

When longer runs of cable are used,

you may need to use a terminator on

the last unit to avoid erratic behaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL90,

5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a

3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

Termination reduces signal

transmission problems and

interference. It is always

advisable to connect a DMX

terminal, (resistance 120

Ohm 1/4W) between pin 2

(DMX-) and pin 3 (DMX+) of

the last xture.

5-Pin

2 4

3-Pin

1 2

Pin Conguration

3-Pin 5-Pin

Pin 1 - Ground

Pin 2 - Negative

Pin 3 - Positive

– Pin 4 - N/C

– Pin 5 - N/C

DMX 512

3-Pin XLR output

DMX 512

3-Pin XLR input

GROUND

DMX +

DMX –

DMX 512

5-Pin XLR output

DMX 512

5-Pin XLR input

GROUND

N/C

DMX –

N/C DMX +

1 ground

3 hot

2 cold

3-Pin XLR male 3-Pin XLR female

2 cold

3 hot

1 ground

2 cold

1 ground 5 N/C

3 hot 4 N/C

5-Pin XLR male 5-Pin XLR female

4 N/C

5 N/C 1 ground

3 hot 2 cold

www.prolight.co.uk Power Par 54 MKII User Manual 8

Multiple xture power linking

Power linking:

This xture provides power linking via the power output on the rear allowing multiple units to be

connected together. The maximum number of xtures that can be connected is 10 xtures @ 240V

or 5 xtures @ 120V (including the rst xture). After the maximum number of xtures are

connected a new power run will need to be started.

Please note: Caution should be used when power linking other xtures to the Power Par 54 MKII as the

power consumption of other xtures will vary. LED xtures tted with switch mode power supplies often

require 2/3 times more current on startup, these may require their own power source.

POWER CONSUMPTION: 165W

POWER PAR 54 MKII

www.prolight.co.uk

FUSE: F3A 250V

POWER CONSUMPTION: 165W

POWER PAR 54 MKII

www.prolight.co.uk

FUSE: F3A 250V

www.prolight.co.uk Power Par 54 MKII User Manual 9

www.prolight.co.uk Power Par 54 MKII User Manual 10

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems Pulse Tube Lithium Bedienungsanleitung

Equinox Systems

Equinox Systems Flame Machine 1.5M Bedienungsanleitung

Equinox Systems

Equinox Systems CARBON Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED368 Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Wash RGBA Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED064 Bedienungsanleitung

Equinox Systems

Equinox Systems Waterwave XP Bedienungsanleitung

Equinox Systems

Equinox Systems Scantastic 4 Bedienungsanleitung

Equinox Systems

Equinox Systems Power Par 54 MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems Hallucination Bedienungsanleitung

Equinox Systems

Equinox Systems PRO DJ Booth Quad-colour Starcloth Bedienungsanleitung

Equinox Systems

Equinox Systems Six Shooter MKII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED162 Installations- und Betriebshandbuch

Equinox Systems

Equinox Systems EQLED12N Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED039A Bedienungsanleitung

Equinox Systems

Equinox Systems Triton Beam EQLED071 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED082 Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer RGB Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED138 Bedienungsanleitung

Equinox Systems

Equinox Systems Helix Scan XP 150W Scanner Bedienungsanleitung

Equinox Systems

Equinox Systems Avalanche EQLED358 Bedienungsanleitung

Equinox Systems

Equinox Systems FEVER Bedienungsanleitung

Equinox Systems

Equinox Systems C-Shot Bedienungsanleitung

Equinox Systems

Equinox Systems Crossfire XP Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung