Equinox Systems CARBON Bedienungsanleitung

CARBON

order code: EQLED22

user manual

www.prolight.co.uk

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Equinox Carbon Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the Equinox carton the following items:

1, Carbon Unit 2, Power cable 3, Instruction manual

Technical Specications:

Voltage: AC 230 ~ 50Hz

192 Ultra bright 10mm LED’s (R: 72, G: 48, B:72)

Dimensions: 320 x 230 x 230mm

Weight: 5Kg

Operating modes: 1, Programme Selection

2, Stand Alone

3, DMX 512: 3 channels

4, Sound activated

5, Master/Slave Mode

Equinox Carbon Technical specications

Overview:

1, DMX input

2, DMX output

3, Power input

4, Power output

5, LED display

6, Fuse (0.5A)

7, Mode selection buttons

8, Microphone

Operation:

There are 5 different operation modes to choose from:

1) Built-in programmes 2) Auto run 3) DMX control mode

4) Sound Activated 5) Master/Slave mode

1, Selecting Built-in programmes

Mode button - By pressing the “MODE” button under the LED display, the LED display will show

“PRXX”, then you can select any of the prorgammes using the “UP” and “DOWN” buttons.

NOTE: PR is the abbreviation for programmes

Set up button - After pressing the MODE button you can select the speed by pressing the “SET

UP” button to display “SXXX”. From this you can select the speed value from “S001” to “S100”

via the “UP” and “DOWN” buttons. If you would like to set the Flash frequencies you can do this

by pressing the “SET UP” button twice to display “FXXX”, then set your desired ash frequency

from “F001” to “F100” via the “UP” and “DOWN” buttons

2, Auto Run Mode

Mode button - Press the MODE button until the LED display shows “AUTO”, then the unit will run

in the Auto Run mode.

SET UP Button - After you have pressed the mode button, press the “SET UP” button to show

“NXXX”, then select your running frequency from “N001” to “N100” for the running times

via the “UP” and “DOWN” buttons.

3, DMX Mode

Mode button - Press the MODE button until the LED display shows “DXXX”.

UP and DOWN Buttons - After you have pressed the mode button, set up the desired DMX

address from “D001” to “D512” via the “UP” and “DOWN” buttons.

For Example if the LED display shows:

a) “D_ _ _”, it means it is waitng for the hundreds input.

b) “D0 _ _”, it means it is waitng for the tens input.

c) “D00 _”, it means it is waitng for the units input.

d) “D001”, it means the DMX address input was successful.

Note: If the DMX address setting is between “D001” to D512, the LED display will show

“PASS” after about 1 second, meaning the new DMX address is set successfully.

Otherwise the LED display will show “FAIL”, meaning the new DMX address setting has

failed.

Equinox Carbon Operation

Function

OFF

Programme 1

Programme 2

Programme 3

Programme 4

Programme 5

Programme 6

Programme 7

Programme 8

Programme 9

Programme 10

Programme 11

Programme 12

Programme 13

Programme 14

Programme 15

Programme 16

Sound active

DMX Value/Function

Note: Under DMX mode, if there is no DMX signal, the point in “D.XXX” will ash

consistently, in order to remind you to connect a DMX signal.

4, Sound Activated Mode

Mode button - Press the MODE button until the LED display shows “SUXX”, then the unit will run

in the Sound Active mode.

UP and DOWN Buttons - After you have pressed the mode button, set up the sensitivity level

from “SU00” to “SU31” via the “UP” and “DOWN” buttons.

5, Slave Mode

Mode button - Press the MODE button until the LED display shows “SLAV”, then the unit will run

in the Slave mode.

• In this mode the Slave units will follow the master unit, which can be used in

“Built-in programmes”,“Auto run” and “Sound activated modes”.

Note: Press the “BLACKOUT” button to turn the unit on/off. After turning off the unit, if you

turn it on again, the programmes will retain the last programme the unit was in when it was

last switched off.

Equinox Carbon Operation

NO:

DMX

value

1-14

15-29

30-44

45-59

60-74

75-89

90-104

105-119

120-134

135-149

150-164

165-179

180-194

195-209

210-224

225-239

240-255

Speed

Not used

Speed

0 - 255

Sensitivity

0 - 255

Flash

Not used

Flash

0 - 255

(0 - 40Hz)

Channel 1 Channel 2 Channel 3

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the

shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Equinox Carbon can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Equinox Carbon DMX Set up

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Equinox Carbon DMX Set up

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Equinox Systems DJ-Equipment Handbücher

Equinox Systems

Equinox Systems MicroPar UV EQLED028 Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion 140 Bedienungsanleitung

Equinox Systems

Equinox Systems Hot Rod EQLED089 Bedienungsanleitung

Equinox Systems

Equinox Systems Ultra LED Scan EQLED75 Bedienungsanleitung

Equinox Systems

Equinox Systems SpectraPix Batten Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT XP MKIII Bedienungsanleitung

Equinox Systems

Equinox Systems Pulse Tube Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED138 Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer Strobe Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Quad Bedienungsanleitung

Equinox Systems

Equinox Systems Six Shooter MKII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED162 Installations- und Betriebshandbuch

Equinox Systems

Equinox Systems EQLED368 Bedienungsanleitung

Equinox Systems

Equinox Systems Twin Shot MKII Electric Confetti Launcher Bedienungsanleitung

Equinox Systems

Equinox Systems Stratos Duo RGB Bedienungsanleitung

Equinox Systems

Equinox Systems Butterfly Quad Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Tri MKII Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED064 Bedienungsanleitung

Equinox Systems

Equinox Systems HYPE Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED135 Bedienungsanleitung

Equinox Systems

Equinox Systems C-Shot Bedienungsanleitung

Equinox Systems

Equinox Systems Midas Spot Bedienungsanleitung

Equinox Systems

Equinox Systems BLITZER Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED53 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung