Equinox Systems Fusion 50 Bedienungsanleitung

Equinox Fusion 50

User Manual

Contents

1. Safety Instructions

2. Features & Specifications

3. How To Set The Unit

4. How To Control The Unit

5. Troubleshooting

6. Fixture Cleaning

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to

another user be sure that they also receive this.

Unpack and check carefully that there is no transportation damage before

using the unit.

!Before operating, ensure that the voltage and frequency of the power

supply match the power requirements of the unit.

!It’s important to ground the yellow/green conductor to earth in order to

avoid electric shock.

!The unit is for indoor use only. Use only in a dry location.

!The unit must be installed in a location with adequate ventilation, at

least 50cm from adjacent surfaces. Be sure that no ventilation slots are

blocked.

!Disconnect the mains power before replacement or servicing.

!Make sure there are no flammable materials close to the unit while

operating as they may cause a fire hazard.

!Always use a safety cable when installing this unit. Do not carry the unit

by its head only, always carry it using the base.

!The maximum ambient temperature is to: 40. Don’t operate it where

the temperature is higher than this.

!In the event of a serious operating problem stop using the unit

immediately. Never try to repair the unit by yourself. Repairs carried out

by unskilled people can lead to damage or malfunction. Please contact

the nearest authorized technical assistance center. Always use the same

type spare parts.

!Do not touch any power cables during operation as the high voltage may

cause an electric shock.

Warning

!To prevent or reduce the risk of electrical shock or fire, do not expose

the unit to rain or moisture.

Do not open the unit within five minutes after switching off.

!The housing and lenses must be replaced if they are visibly damaged.

Installation

The unit should be mounted via its screw holes onto the bracket. Always

ensure that the unit is firmly fixed to avoid vibration and slipping while

operating. Make sure that the structure to which you are attaching the

unit to is secure and is able to support a weight of 10 times of the unit’s

weight. Always use a safety cable that can hold 12 times of the weight of

the unit when installing the fixture.

The equipment must be installed by professionals and it must be

installed in a place where is out of the reach of people and no one can

pass by or under it.

2. Features & Technical Specification

Control: Sound active, auto, Master/slave and DMX-512 modes

DMX Channels: 9 channels

Electronic dimming: 0-100%

Electronic strobe with pulse and random effects

High output with low power consumption

Compact size and low weight

Voltage: 100V~240V, 50/60Hz

Fuse: T 3.0A

Power consumption: 85W

Light source: 8W x 7pcs 4 in1 RGBW quad color LED

Dimension: 173 x 173 x 249 mm

Weight: 3.6 kg

Pan/Tilt: 540°/180°

Power sockets:IEC

XLR sockets:3-pin XLR IN/OUT

Please read the instructions carefully as they include important

information about installation, usage and maintenance.

3. How To Set The Unit

3.1 Control panel

Display

Shows the various menus and selected functions

Button

Selects the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER

Confirms the selected functions

Mains input

Connection to the power supply.

DMX input/output

For DMX-512 linking. Use a 3-pin XLR cables to link to the controller or to

other units.

3.2 Main Functions

To select any of the given functions, press the MENU button up to where

the required function is showing on the display. Select the function by

pressing the ENTER button and the display will blink. Use the DOWN and

UP buttons to change the mode. Once the required mode has been

selected, press the ENTER button to confirm. To go back to the functions

without any changes, press the MENU button again. Press and hold the

MENU button for one second or wait for one minute to go back to the main

menu.

The main functions are as below:

ADDR

001-512

SLND

SL1

SL2

MAST

SHND

SH1

SH2

SH3

SH4

SOUN

OFF

SENS

000-255

BLND

YES

LED

OFF

BALA

RED

GREEN

BLUE

DISP→INVERT

PAN INVERT

YES

TILT INVERT

YES

TEST

VER

REST

DMX Address Setting

Press the MENU button to select . Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to choose the address

from 1-255. Once the address has been selected, press the ENTER button

to confirm. To go back to the functions without any changes press the

MENU button again. Press and hold the MENU button for one second or

wait for one minute to go back to the main menu.

Master Mode or Slave Mode

Press the MENU button to select . Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the

(Slave 1), (Slave 2) or (Master) mode. Once the mode

has been selected, press the ENTER button to confirm. To go back to the

functions without any changes press the MENU button again. Press and

hold the MENU button for one second or wait for one minute to go back to

the main menu.

Show Mode

Press the MENU button to select . Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the

(show 1) or (show 2) or (show 3) or (show 4) mode.

Once the mode has been selected, press the ENTER button to confirm. To

go back to the functions without any changes press the MENU button

again. Press and hold the MENU button for one second or wait for one

minute to go back to the main menu.

Sound Mode

Press the MENU button to select . Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the

(sound on) or (sound off) mode. Once the mode has been selected,

press the ENTER button to confirm. To go back to the functions without

any changes press the MENU button again. Press and hold the MENU

button for one second or wait for one minute to go back to the main menu.

Sound Sensitivity

Press the MENU and use UP and DOWN button to select and select

the sound sensitivity between value 0 and 255. Press the ENTER button

for confirmation after value selection. To go back to the functions without

any changes press the MENU button again.

Blackout Mode

Press the MENU button to select . Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the (yes

blackout) or (no blackout) mode. Once the mode has been

selected, press the ENTER button to confirm. To go back to the functions

without any changes press the MENU button again. Press and hold the

MENU button for one second or wait for one minute to go back to the main

menu.

Led Display

Press the MENU button to select . Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the (Led

display on) or (Led display off) mode. Once the mode has been

selected, press the ENTER button to confirm. To go back to the functions

without any changes press the MENU button again. Press and hold the

MENU button for one second or wait for one minute to go back to the main

menu.

Dimmer Calibrate

Press the MENU button to select . Press the ENTER button to

confirm, the current mode will blink. Use the DOWN and UP buttons to

select Red/ Green/Blue. Once the mode has been selected, press the

ENTER button to setup. Use the DOWN and UP buttons to change the

value (125~255). Once the mode has been selected, press the ENTER

button to confirm. To go back to the functions without any changes press

the MENU button again. Press and hold the MENU button for one second or

wait for one minute to go back to the main menu.

Display Inversion

Press the MENU button to select . Press the ENTER button to change

to the mode (display normal), It will be automatically saved after 8

seconds. Press the ENTER button again to select the mode (display

inversion). To go back to the functions press the MENU button. Press and

hold the MENU button for one second or wait for one minute to go back to

the main menu.

Display normal mode is for floor standing the unit.

Display inversion mode is for hanging the unit from a ceiling.

Pan Inversion

Press the MENU button to select . Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the

(normal) or (pan inversion) mode. Once the mode has been

selected, press the ENTER button to confirm. To go back to the functions

without any changes press the MENU button again. Press and hold the

MENU button for one second or wait for one minute to go back to the main

menu.

Tilt Inversion

Press the MENU button to select . Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the

(normal) or (tilt inversion) mode. Once the mode has been

selected, press the ENTER button to confirm. To go back to the functions

without any change press the MENU button again. Press and hold the

MENU button for one second or wait for one minute to go back to the main

menu.

Auto-Test

Press the MENU button to select . Press the ENTER button and the

unit will run a self-test with its built-in programs. To go back to the

functions without any changes press the MENU button again. Press and

hold the MENU button for one second or wait for one minute to go back to

the main menu.

Reset

Press the MENU button to select . Press the ENTER button and all

channels of the unit will return to their standard position.

4. How To Control The Unit

1. Master/slave built-in preprogram function

2. Universal DMX controller

There is no need to turn the unit off when you change the DMX address as

new DMX address setting will be effected at once. Every time you turn the

unit on, it will show “ ”on the display and move all the motors to

their ‘home’ position and you may hear some noises for about 20 seconds.

After that the unit will be ready to receive DMX signal or run the built in

programs.

4.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control

the other units to give an automatic, sound activated, synchronized light

show. This function is good when you want an instant show. You have to

set the first unit as master and select show 1, show 2, show 3 or show

4from the Show Mode. The other units must be set to either Slave 1

(normal) or Slave 2 (2 light show) mode. A DMX cable between the units

for daisy chain is needed.

2-light show

In slave mode, Slave 1 means the unit works normally and Slave 2

means 2-light show. In order to create a great light show, you can set

Slave 2 on the second unit to get contrast movement to each other, even

if you have two units only.

4.2 DMX Controller

By using a universal DMX controller to control the units, you will need to

set a DMX address from 1 to 512 so that the units can receive a DMX

signal.

Press the MENU button until is showing on the display. Press the

ENTER button and the display will blink. Use the DOWN and UP buttons

to change the DMX-512 address. Once the address has been selected,

press the ENTER button to confirm. To go back to the functions without

any changes press the MENU button again. Press and hold the MENU

button one second or wait for one minute to go back to the main menu.

Please refer to the below diagram to address your first 4 units：

Channel

mode

Unit 1

Address

Unit 2

Address

Unit 3

Address

Unit 4

Address

9 channels

4.3 DMX 512 Configuration

Channel

Value

Function

0-255

Pan

0-255

Tilt

0-255

Red

0-255

Green

0-255

Blue

0-255

White

248-255

Open

240-247

Random Strobe

232-239

Open

190-231

Slow close

Fast Open

182-189

Open

140-181

Fast close

Slow Open

132-139

Open

16-131

Strobe (slow-fast)

8-015

Open

0-007

0-255

Master dimmer

0-010

Stand alone (Sound mode)

011-255

Sound sensitivity low - high.

4.4 DMX512 CONNECTION

1. In the last unit, the DMX has to be terminated with a termination plug.

Solder a 120 ohm 1/4W resistor between pin 2(DMX-) and pin

3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the

last unit.

2. Connect the units together in a `daisy chain` with an XLR plug from

the output of the unit to the input of the next unit. The cable can not

be branched or split to a `Y` cable.

3. The DMX output and input connectors are a pass-through type to

maintain the DMX circuit when one of the units’ power is

disconnected.

4. Each lighting unit needs to have an address setup to receive the data

sent by the controller. The address number is between 0-512 (usually

0 & 1 are equal to 1).

5. The end of the DMX 512 system should be terminated to reduce signal

errors.

6. 3 pin XLR cable wiring configuration

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal

(+)

5.Troubleshooting

Following are a few common problems that may occur during

operation and some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of the power and the main fuse.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX cables to see if linked

correctly.

2. If the DMX address is showing but no response to the controller,

check the address settings and DMX polarity.

3. Try another DMX controller.

C. No response to the sound

1. Make sure the unit is not receiving a DMX signal.

2. Check the microphone to see if it is good by tapping it. The

microphone is located on the bottom plate of the unit.

6. Fixture Cleaning

The cleaning of external optical lenses must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding

can cause a greater accumulation of dirt on the unit’s optics.

Clean with a soft cloth using normal glass cleaning fluid or mild soapy

water.

!Always dry the parts carefully.

!Clean the external optics at least every 20 days.

----------------------www.prolight.co.uk----------------------------------

Inhaltsverzeichnis

Andere Equinox Systems Scheinwerfer Handbücher

Equinox Systems

Equinox Systems Revolution EQLED80 Bedienungsanleitung

Equinox Systems

Equinox Systems Eclipse Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED020 Bedienungsanleitung

Equinox Systems

Equinox Systems WATE03 Bedienungsanleitung

Equinox Systems

Equinox Systems LIGHTNING CRACKER 2 Bedienungsanleitung

Equinox Systems

Equinox Systems Ripper EQLA27 Bedienungsanleitung

Equinox Systems

Equinox Systems SF-300 Bedienungsanleitung

Equinox Systems

Equinox Systems Crossfire EQLED061 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED041 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED002 Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion Razor Beam EQLED006 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED71 Bedienungsanleitung

Equinox Systems

Equinox Systems STRO11 Lightning Cracker Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED65 Giga Bar System Bedienungsanleitung

Equinox Systems

Equinox Systems Ballero Spot Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED76 Six Shooter Bedienungsanleitung

Equinox Systems

Equinox Systems Cabaret Colour Bedienungsanleitung

Equinox Systems

Equinox Systems Triclops Beam Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung