Ergotron WorkFit-A, Single LCD Mount, LD Bedienungsanleitung

1 of 12

888-45-319-G-01 rev. C • 09/13

Reduce.Reuse.Recycle

Intended for use with Apple® 21.5” iMac and 27” iMac (late 2012 and newer).

Maximum total weight (including iMac, keyboard and mouse) not to exceed 25 lbs (11.34 kg)

For local customer care phone numbers visit: http://contact.ergotron.com

2 of 12

888-45-319-G-01 rev. C • 09/13

Important!

You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting

adjustments.This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or

dicult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your

product and the adjustment, it may take many turns to notice a dierence. Any time equipment is added or removed from this product, resulting in a

change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

4 mm

13mm

Optional for Pan Adjustmet

Arm Worksurface/Keyboad

Tray Support

Worksurface

M6 x14 mm

4x 2x

2x 4x

M5 x 16mm

Keyboard Tray

8 mm

WARNING! Stored Energy Hazard:The arm mechanism is

under tension and will move up rapidly, on its own, as soon

as attached equipment is removed. For this reason, DO NOT

remove equipment unless the arm has been moved to the

highest position! Failure to follow this instruction may result

in serious personal injury and/or equipment damage!

WARNING

Components

Hardware

Tools Needed

3 of 12

888-45-319-G-01 rev. C • 09/13

To expand the arm

extension, follow

instructions below.

To expand the arm

extension, follow

instructions below.

1. Desk Clamp 2. Desk Clamp

Expand Arm Extension

How to expand the arm extension.

3. Grommet Hole 4. Grommet Hole

Max: 25.5"

(648 mm)

Max: 31.5"

(800 mm)

Max: 23.5"

(597 mm)

Max: 29.5"

(749 mm)

4 mm

abc

Remove the 4 screws at the

base using the provided

4mm hex wrench.

Flip the base around (turn

180 degrees clockwise).

Re-insert the 4 screws and tighten

with the 4mm hex wrench.

1Arm Extension and Desk Size:

The keyboard tray is designed to extend over the edge of your desk. You can expand the extension of the arm if

you need to based on your desk size. To determine if you need to expand your arm extension, refer to the 4 desk

dimensions below:

4 of 12

888-45-319-G-01 rev. C • 09/13

4 mm

Mount arm to desk.

Tighten the bolts with the provided 8 mm wrench.

8 mm

Clamp congurations for dierent desk thickness

OPTIONAL GROMMET HOLE MOUNT

- Follow these instructions if you want to change your clamp to a grommet hole mount.

Remove clamp bracket screws

with 4mm hex wrench.

Insert provided bolt into provided grommet

plate. Attach grommet plate with 4 mm hex

wrench and screws removed in step b.

Remove clamp plate

screws with 4mm hex

wrench. Retain screws.

Position arm with attached grommet plate

over grommet hole (make sure bolt is

centered in hole).Thread grommet bracket

and wing nut onto bolt and tighten.

0.78"-1.78" (20-45mm) 1.70"-2.56" (43-65mm)

4 mm

0.78"-2.56"

(20-65mm)

0.5"-2.5"

(13-64mm)

CAUTION: Bolt

must be centered in hole.

Warning: Because mounting surface materials can

vary widely, it is imperative that you make sure mounting surface

is strong enough to handle mounted product and equipment.

5 of 12

888-45-319-G-01 rev. C • 09/13

3Attach the support bracket to the arm.

A tab on the support bracket ts into

a slot on the arm plate.

Tilt the top of the support bracket down and slide

forward until the tab meets the slot.

Insert the four provided M6 x 14mm Phillips screws into

the platform and tighten with a Phillips screwdriver.

M6x 14mm

6 of 12

888-45-319-G-01 rev. C • 09/13

Attach the keyboard tray to the support bracket.

Slide the keyboard tray onto the support bracket until it“clicks”into place.

Place your display with stand on top of the support bracket.

NOTE: the front end of the display stand

should slide under the plastic clip.

Push your display stand backwards until it meets the

back of the support bracket.

7 of 12

888-45-319-G-01 rev. C • 09/13

Set your keyboard and mouse on top of the keyboard tray.

Route the keyboard and mouse cables through the slots and over the

support bracket platform.

NOTE: pull a sucient length of cable

to reach the back of the display since it

will be dicult to adjust after the work-

surface is attached in the next step!

For 21.5”iMac only: (for 27”display skip to step 9)

Before attaching the worksurface to the support bracket turn the worksurface over and

apply one of the provided pads over each of the pads already attached to the

bottom of the worksurface.

Tuck cables into slot

behind keyboard tray.

8 of 12

888-45-319-G-01 rev. C • 09/13

IMPORTANT: Make sure the front tabs of

the worksurface are properly engaged!

Insert the provided M5 x 16mm Phillips screws and tighten with a Phillips screwdriver.

M5 x 16mm

Bottom view of

worksurface showing tabs.

CAUTION: Do not strip out screws when tightening!

Attach the worksurface to the support bracket.

Slide the worksurface down and back onto the support bracket.

9 of 12

888-45-319-G-01 rev. C • 09/13

10 Route display cables and secure with cable ties.

10 of 12

888-45-319-G-01 rev. C • 09/13

Increase Lift Strength

If the mounted weight is too heavy or this

product does not stay up when raised, then

you'll need to increase Lift Strength:

Decrease Lift Strength

If the mounted weight is too light or this

product does not stay down when lowered,

then you'll need to decrease Lift Strength:

8 mm

123

1. Lift up and down to test tension.

2. If adjustment is needed, move to highest level.

3. Use the provided 8mm wrench to adjust the tension.

Up-and-down Adjustment

Adjustment Step

Important! You will need to adjust this product after installation is complete. Make sure all your equipment

is properly installed on the product before attempting adjustments. This product should move smoothly

and easily through the full range of motion and stay where you set it. If movements are too easy or dicult

or if product does not stay in desired positions, follow the adjustment instructions to create smooth and

easy movements. Depending on your product and the adjustment, it may take many turns to notice a

dierence. Any time equipment is added or removed from this product, resulting in a change in the weight

of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

Andere Handbücher für WorkFit-A, Single LCD Mount, LD

Inhaltsverzeichnis

Andere Ergotron Desktop Handbücher

Ergotron

Ergotron WorkFit-S Bedienungsanleitung

Ergotron

Ergotron WorkFit-P Bedienungsanleitung

Ergotron

Ergotron StyleView Bedienungsanleitung

Ergotron

Ergotron WorkFit-P Bedienungsanleitung

Ergotron

Ergotron WorkFit-P Bedienungsanleitung

Ergotron

Ergotron StyleView Bedienungsanleitung

Ergotron

Ergotron StyleView Bedienungsanleitung

Ergotron

Ergotron StyleView Bedienungsanleitung

Ergotron

Ergotron WorkFit-Z mini Bedienungsanleitung

Ergotron

Ergotron WorkFit-S Bedienungsanleitung

Ergotron

Ergotron Steve's Station Advanced Bedienungsanleitung

Ergotron

Ergotron 97-583-009 Bedienungsanleitung

Ergotron

Ergotron Command Post Bedienungsanleitung

Ergotron

Ergotron WORKFIT Bedienungsanleitung

Ergotron

Ergotron Desktop 16 Bedienungsanleitung

Ergotron

Ergotron StyleView VL Enclosure Fehlerbehebungshandbuch

Ergotron

Ergotron 48 Unit Management Cart Bedienungsanleitung

Ergotron

Ergotron TeachWell Mobile Digital WorkSpace Bedienungsanleitung

Ergotron

Ergotron STYLEVIEW Series Bedienungsanleitung

Ergotron

Ergotron WorkFit-P Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung