Ericsson EDA 2530 Schulungshandbuch

1/153 22-FGC 101 0239/2 Uen Rev J

EDA 2530 Commissioning Procedure fo

Cable and Wireless Access

EDA 2530 R4.21 GA EC2

Commissioning Instructions

EDA 2530 Commissioning Procedure for Cable and Wireless Access

1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01 ©Ericsson AB 2010

Commercial in confidence 2 (200)

Disclaimer

No part may be reproduced, disclosed or used except as authorised by contract or

other written permission. The copyright and the foregoing restriction on reproduction

and use extend to all media in which the information may be embodied.

The information in this work is the property of Ericsson Limited. Except as

specifically authorised in writing by Ericsson Limited, the receiver of this work shall

keep the information contained herein confidential and shall protect the same in

whole or in part from disclosure and dissemination to third parties. Disclosure and

disseminations to the receiver's employees shall only be made on a strict need to

know basis. The information in this work is subject to change without notice and

Ericsson Limited assumes no responsibility for factual inaccuracies or typographical

errors.

Ericsson Limited has used all reasonable endeavours to make sure that the

information contained in this work is accurate at the release date but reserves the

right to make changes, in good faith, to such information from time to time.

Trademarks

Ericsson and the Ericsson logo are trademarks of Telefonaktiebolaget LM Ericsson.

rights reserved. Adobe and Acrobat are trademarks of Adobe Systems Incorporated.

All trademarks and registered trademarks mentioned in a document of this collection

are the property of their respective holders.

EDA 2530 Commissioning Procedure for Cable and Wireless Access

1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01 ©Ericsson AB 2010

Commercial in confidence 3 (200)

Contents

1Introduction............................................................................................7

1.1 Objective.................................................................................................. 7

1.2 Scope ...................................................................................................... 7

1.3 Safety Procedures ................................................................................... 7

1.4 Static Sensitive Device Handling Precautions......................................... 8

1.5 Optical Device Precautions ..................................................................... 8

1.6 Inspection/Cleaning Procedure For Optical Connectors.......................... 8

1.7 Commissioning Test Records.................................................................. 8

1.8 Required Information For Commissioning ............................................... 9

1.9 Documentation Change Request ............................................................ 9

2EDA 2530 MSAN Equipment...............................................................11

2.1 General Equipment Description............................................................. 11

2.2 Equipment Overview ............................................................................. 11

2.3 Rack And Subrack Description.............................................................. 14

2.3.1 Rack ...................................................................................................... 14

2.3.2 EDA 2530 Subrack ................................................................................ 14

2.4 Subrack Composition ............................................................................ 15

2.4.1 Composition Rules ................................................................................ 15

2.4.2 EDA2530E Standard Configuration for CWA Parent and Stand Alone

Shelf ...................................................................................................... 16

2.4.3 Network Interface Units ......................................................................... 18

2.4.4 Subscriber Interface Units ..................................................................... 20

2.4.5 Subrack Connection Units ..................................................................... 23

2.4.6 Fan Tray (151-2984/02)......................................................................... 32

3Resources ............................................................................................33

3.1 Documentation ...................................................................................... 33

3.2 Tools...................................................................................................... 33

3.3 Test Equipment ..................................................................................... 33

3.3.1 PC Connection Cables for Commissioning............................................ 34

3.4 Test Cables ........................................................................................... 35

3.4.1 RS232 Serial Cable Set (151-2502/01) ................................................. 36

3.5 Local Craft Terminal (LCT) Installation.................................................. 37

3.5.1 Removal of Old Issue of EDA Hub Software ......................................... 37

3.5.2 Installation of Local Operator Software on P.C...................................... 37

3.5.3 Install Application Software From CD ROM........................................... 38

3.5.4 LCT 07.02.05 – Known Issue with Java Version 1.6 ............................. 39

4Commissioning Requirements...........................................................41

4.1 Description Of Testing Activities............................................................ 41

4.2 Test Records ......................................................................................... 41

4.3 Preliminary Checks................................................................................ 41

4.3.1 Equipment Positioning........................................................................... 41

4.3.2 Card Equipping...................................................................................... 41

4.3.3 Cabling .................................................................................................. 42

4.3.4 Power Supply and Grounding Connections........................................... 43

4.4 Earthing And D.C. Supply Checks......................................................... 44

4.5 Power Supply Connection Unit Check................................................... 45

EDA 2530 Commissioning Procedure for Cable and Wireless Access

1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01 ©Ericsson AB 2010

Commercial in confidence 4 (200)

4.5.1 Labelling.................................................................................................45

5Initial Configuration .............................................................................47

5.1 IP Address Configuration Of PC Used As LCT ......................................47

5.2 Common Part Card CF Download..........................................................50

5.3 Subrack Equipping .................................................................................53

5.4 Logon to The EDA 2530 Via LCT...........................................................54

5.5 Reset The Backplane EPROM...............................................................55

5.6 Software Inventory Check ......................................................................57

6Software Download/Upgrade ..............................................................61

7Configure IP and Ethernet Management............................................67

7.1 Configure The Optical SFP Modules Gigabit Ethernet...........................69

7.2 Configure CP Ethernet Interfaces ..........................................................72

7.2.1 Configure CP Port 1 ...............................................................................72

7.2.2 Configure CP Port 2 ...............................................................................73

7.2.3 Configure CP Port 3 (If required)............................................................73

7.2.4 Configure CP Port 4 (If required)............................................................73

7.3 Configure EDA 2530 Tag Protocol ID/Bridging Parameters...................74

7.4 ADSL Card Configuration Files ..............................................................75

7.5 SHDSL Card Configuration Files............................................................75

7.6 Configure Static VLANs..........................................................................76

7.7 Adding Interfaces to the Static VLANs ...................................................79

7.7.1 Create S-VLANs for Additional ADSL Cards (If required) ......................81

7.7.2 Create S-VLANs for SHDSL Cards (If required) ....................................83

7.7.3 Create S-VLANs for POTS Cards (If required).......................................85

7.7.4 Complete VLAN Creation.......................................................................88

7.7.5 Create S-VLANs on the “Parent” to Subtend Child#2 (If required).........88

7.7.6 Create S-VLANs on the “Parent” to Subtend Child#3 (If required).........94

7.8 Configuring The IBM Sub-Interface........................................................96

7.9 Assign The IBM IP Address ...................................................................98

7.10 Configure The Default Gateway...........................................................100

7.11 xDSL Bridge Management - Configure xDSL Bridge ...........................101

7.12 xDSL Bridge Management - Configure PVC ........................................104

7.12.1 Download xDSL PVC Management File ..............................................104

7.12.2 Check PVC Management PPPoA Payload & MRU Settings................105

7.12.3 Configure PVC Management ...............................................................106

7.12.4 Configure Additional xDSL Cards.........................................................111

7.13 xDSL Bridge Management – Downstream Flow Assignment...............112

7.14 Configure ADSL Profiles ......................................................................114

7.15 Configure SHDSL Line Profiles............................................................116

7.16 Configure SHDSL Stack Profiles..........................................................118

7.17 Configure POTS Card(s) ......................................................................121

7.17.1 POTS Card Configuration Files............................................................121

7.17.2 Step 1: LCT 07.02.05 – Known Issue with Java Version 1.6 ...............121

7.17.3 Step 2: Add POTS Card(s) Interfaces to Static VLANs........................121

7.17.4 Step 3: Configure UK National Mapping ..............................................122

7.17.5 Step 4: Configure ITAM For Double Play .............................................124

7.17.6 Step 5: Configure RTP Profiles ............................................................126

7.17.7 Step 6: Check TOIP Profiles ................................................................130

7.17.8 Step 7: Configure POTS Cards ............................................................131

EDA 2530 Commissioning Procedure for Cable and Wireless Access

1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01 ©Ericsson AB 2010

Commercial in confidence 5 (200)

7.17.9 Step 8: Build Voice Configuration........................................................ 135

8EDA 2530 Equipment Test and Alarm Checks................................147

8.1 Equipment Test ................................................................................... 147

8.1.1 Optical Launch Power Test ................................................................. 147

8.1.2 Unit Status Check................................................................................ 147

8.2 Alarm Checks ...................................................................................... 148

8.2.1 Common Part Alarm Check ................................................................. 148

8.2.2 Power Supply Alarm Check ................................................................. 148

8.2.3 FAN Unit Extraction/Insertion .............................................................. 149

8.2.4 64 x ADSL2+ Unit Extraction/Insertion ................................................ 150

8.2.5 32 x SHDSL Unit Extraction/Insertion.................................................. 150

8.2.6 64 x POTS/VoIP Unit Extraction/Insertion ........................................... 151

8.3 Set Equipment Time and Date ............................................................ 152

9Test ADSL2+, POTS, SHDSL & Connection Units..........................153

9.1 Configure/Activate/Test 64 Port Adsl2+ Units ..................................... 153

9.1.1 Check 64 x ADSL Cards for ADSL2 + Configuration........................... 153

9.1.2 Configure 64 x ADSL Card for ADSL2 + Configuration Profile............ 155

9.1.3 Test 64 x ADSL2+ Card....................................................................... 161

9.2 Configure/Activate/Test 32 Port SHDSL Units..................................... 163

9.2.1 Configure 32 x SHDSL Card Profiles .................................................. 163

9.2.2 Test 32 x SHDSL Cards ...................................................................... 168

9.3 Test 64 x POTS/VoIP Cards................................................................ 170

9.3.1 Test 64 x POTS/VoIP Cards................................................................ 170

9.4 Test iTAM Splitter Connection Unit...................................................... 172

9.4.1 Check Test Relay Switching Correctly................................................. 172

9.4.2 Configure ITAM Splitter Unit from LCT ................................................ 174

9.4.3 Continuity Testing LLUT (Line) to LLUL (POTS) Blocks...................... 177

9.5 End Of Stand Alone Configuration/Testing.......................................... 177

10 Appendix - Common Part Unit DIP Setting .....................................179

11 Test Records......................................................................................181

11.1 Test Record Procedure ....................................................................... 181

11.2 Certification Of Tests ........................................................................... 184

12 Glossary Of Terms ............................................................................187

13 References .........................................................................................191

14 Change Information...........................................................................193

EDA 2530 Commissioning Procedure for Cable and Wireless Access

1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01 ©Ericsson AB 2010

Commercial in confidence 6 (200)

This page intentionally blank to facilitate double sided printing.

EDA 2530 Commissioning Procedure for Cable and Wireless Access

1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01 ©Ericsson AB 2010

Commercial in confidence 7 (200)

1 Introduction

1.1 Objective

The objective of this document is to detail the procedures for commissioning of the

EDA 2530 when used in the Cable and Wireless Access network.

1.2 Scope

This document will be used to commission the EDA 2530 DLE Node on site.

The DLE IP DSLAM EDA 2530 (EDA 0x0x) shelf can be equipped with up to ten 64

x ADSL2+ Cards and ten 64 x POTS/VoIP Cards and up to four 32 x SHDSL Cards

as required. The 64 x POTS/VoIP Card will be configured for H.248 protocol. The

ADSL2+, POTS/VoIP Cards and 32 x SHDSL Cards VLANs will be routed to the

GigaBit Ethernet Port of the EDA 2530 CP-IP Card. The Common Part “Backhaul”

GigaBit Ethernet Port will be connected to the IP network.

The tests in the document are to prove the functionality of the EDA 2530. These

tests will include the set-up and connection of the Local Controller, the loading of

site specific Database and the setting up of circuits through the EDA 2530.

Engineers MUST familiarise themselves with the procedure and be aware of and

observe all safety precautions BEFORE starting the commissioning procedure.

1.3 Safety Procedures

All procedures should be carried out in accordance with the Safety Rules and Safety

Notices as stated in the product handbook.

EDA 2530 Commissioning Procedure for Cable and Wireless Access

1/153 22-FGC 101 0239/2 Uen Rev J 2010-04-01 ©Ericsson AB 2010

Commercial in confidence 8 (200)

1.4 Static Sensitive Device Handling Precautions

Equipment referred to in this document contain static sensitive devices and

therefore an ESP wrist strap MUST be worn and connected to an ESP bonding point

at all times when handling slide-in-units and socketed devices (PROMS).

1.5 Optical Device Precautions

The EDA Subrack may be equipped with Optical Common Part Units containing

laser transmitters. Never look into a laser transmitter port or into a fibre optic cable.

1.6 Inspection/Cleaning Procedure For Optical Connectors

All optical fibre connectors will require inspection for damage and cleanliness.

1.7 Commissioning Test Records

The commissioning test records at the end of this document must be completed as

the commissioning progresses. A complete set of Test Records must be completed

for each EDA 2530 being commissioned. This should be retained on site for the

customer’s use if requested. Any items outstanding after the acceptance testing is

complete are to be listed in the Outstanding Items Summary at the end of this

document.

When all acceptance testing has been completed successfully, both the Ericsson

and Customer’s representatives must complete the Customer Acceptance Form at

the end of this document. If the Customer’s representative is not present on site

enter N/A (Not Available) for the Customer representative.

EDA 2530 Commissioning Procedure for Cable and Wireless Access

Commercial in confidence 9 (200)

1.8 Required Information For Commissioning

The Customer Network Planning Authority shall be responsible for providing the

following information before commissioning can commence.

a. Unit type and location of cards in the subrack.

b. IP over Ethernet Addresses of each EDA 2530 (DLE Node Address).

c. Site/slot specific IP addresses for POTS cards.

d. IP address of the NTP Server.

e. If available, fibre loss figures for the sub-network under test.

f. The SID document, which specifies Configuration information i.e. Site

location, Floor Plan, Rack Layout, Fuse allocations, MDF block locations for

the EDA 2530 Subrack equipment, and Cable Running Out Lists.

g. Alarm Profile list for each unit type that is to be commissioned in the

subrack.

1.9 Documentation Change Request

In order to allow changes to this document to be implemented quickly, site

engineers are requested to use the Document Change Request Form at the end of

this document. The form should be sent by post, fax or e-mail to the author of this

document for the change request to be considered.

End of section

EDA 2530 Commissioning Procedure for Cable and Wireless Access

Commercial in confidence 10 (200)

This page is left intentionally blank to facilitate double sided printing.

Inhaltsverzeichnis

Andere Ericsson Netzwerkkarte Handbücher

Ericsson

Ericsson EDACS LBI-39076B Benutzerhandbuch

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung

Gigafast

Gigafast EE101-AEX Bedienungsanleitung