ESAB Aristo Origo Feed 3004 Bedienungsanleitung

Valid for serial no. 745--xxx--xxxx0444 408 001 GB 080110

Origot

Feed 3004,

Feed 4804

Instruction manual

-- 2 --

TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3........................................................

2SAFETY 3...........................................................

3 INTRODUCTION 5...................................................

3.1 Equipment 5................................................................

3.2 Control panel 5.............................................................

4 TECHNICAL DATA 6.................................................

5 INSTALLATION 6....................................................

5.1 Lifting instructions 7.........................................................

6 OPERATION 7.......................................................

6.1 Connections and control devices 8............................................

6.2 Water connection 8..........................................................

6.3 Wire feed pressure 9........................................................

6.4 Replacing and inserting Feed 3004 wire 9......................................

6.5 Replacing and inserting Feed 4804 wire 9......................................

6.6 Changing feed rollers on Feed 3004 10..........................................

6.7 Changing feed rollers on Feed 4804 10..........................................

7 MAINTENANCE 11....................................................

7.1 Inspection and cleaning 11....................................................

8 ORDERING SPARE PARTS 11..........................................

DIAGRAM 12............................................................

ORDERING NUMBER 13.................................................

WEAR PARTS 15........................................................

ACCESSORIES 20.......................................................

-- 3 --

bm50d1ea

1SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding

2. The operator must ensure that:

Sno unauthorized person is stationed within the working area of the equipment when it is

started up.

Sno--one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

-- 4 --

bm50d1ea

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precausions when welding.

Ask for your employer’s safety practices which should be based on manufacturers’ hazard data.

ELECTRIC SHOCK - Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

Read and understand the instruction manual before

installing or operating.

CAUTION!

Class A equipment is not intended for use in residential locations where

the electrical power is provided by the public low--voltage supply

system. There may be potential difficulties in ensuring electromagnic

compatibility of class A equipment in those locations, due to conducted

as well as radiated disturbances.

CAUTION!

This product is solely intended for arc welding.

-- 5 --

bm50d1ea

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical equipment

that has reached the end of its life must be collected separately and returned to an

environmentally compatible recycling facility. As the owner of the equipment, you should

get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human

health!

ESAB can provide you with all necessary welding protection and accessories.

2 INTRODUCTION

The wire feed units Feed 3004 / Feed 4804 with control panel MA23 or MA24 are

intended for MIG/MAG welding together with 400A, 500A and 600A CAN

welding power sources.

The wire feed units contain four--wheel drive wire feed mechanisms as well as

control electronics.

They can be used together with wire on ESAB’s MarathonPact, or on wire bobbin

(standard Ø 300 mm, accessory Ø 440 mm).

The wire feed unit can be installed either on the power source trolley, suspended above

the workplace, on a counter balance device or on the floor with or without wheel set.

ESAB’s accessories for the product can be found on page 20.

2.1 Equipment

The wire feed unit is supplied with:

Sinstruction manual for the wire feed unit

Sinstruction manual in English for the control panel

Sdecal with recommended wear parts.

2.2 Control panel

The wire feed unit is supplied with one of the following control panels:

MA23 Knobs for setting the voltage and the wire feed speed /

current. Other settings with push buttons.

MA24 Knobs for setting the voltage / QSettand the wire feed

speed / current. Other settings with push buttons.

See the separate instruction manual for a detailed description of the control panels.

-- 6 --

bm50d1ea

3 TECHNICAL DATA

Feed 3004 Feed 4804

Mains voltage 42 V 50--60 Hz 42 V 50--60 Hz

Power requirement 336 VA 378 VA

Motor current Imax 8A 9A

Wire feed speed 0.8 -- 25.0 m/min 0.8 -- 25.0 m/min

Gun connection EURO EURO

Max. diameter wire bobbin 300 mm (*440 mm) 300 mm (*440 mm)

Wire dimension

Cored wire

0.8 -- 1.6 mm

1.0 & 1.6 mm

0.9 -- 1.6 mm

0.8 -- 2.4 mm

1.0 & 2.4 mm

0.9 -- 2.4 mm

Weight 15 kg 19 kg

Dimensions (l x w x h) 690 x 275 x 420 mm 690 x 275 x 420 mm

Operating temperature -- 1 0 t o + 4 0 ˚C-- 1 0 t o + 4 0 ˚C

Shielding gas

max pressure

All types intended for

MIG/MAG welding

0.5 MPa ( 5 bar)

All types intended for

MIG/MAG welding

0.5 MPa ( 5 bar)

Type of cooling

max pressure

50 % water /

50 % mono--ethylene glycol

0.5 MPa ( 5 bar)

50 % water /

50 % mono--ethylene glycol

0.5 MPa ( 5 bar)

Maximum permissible load at

60% duty cycle 500 A 500 A

Enclosure class IP23 IP23

* Accessories, see page 20.

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

4 INSTALLATION

The installation must be executed by a professional.

WARNING!

When welding in an environment with increased electrical danger, only power

sources intended for this environment may be used. These power sources are

marked with the symbol

-- 7 --

bm50d1ea

4.1 Lifting instructions

Order number for lifting eyelet can be found on page 20.

NOTE! If another mounting device is used, this must be electrically insulated from

the wire feed unit.

5 OPERATION

General safety regulations for the handling of the equipment can be found on

page 3. Read through before you start using the equipment!

When moving the equipment use intended handle. NOTE! Never pull on the gun.

WARNING!

Assure that the side panels are closed during operation.

WARNING!

To prevent the reel from sliding off the hub: Lock the

reel in place by turning the red knob as shown on the

warning label attached next to the hub.

WARNING!

Rotating parts can cause injury, take great care.

-- 8 --

bm50d1ea

WARNING!

There is a risk of tipping if the wire feed unit is fitted with a counterbalance arm.

Secure the equipment, especially if used on an uneven or sloping surface.

5.1 Connections and control devices

1Control panel,

(see separate instruction manual)

6Connection for welding current from power

source, (OKC)

2Connection for remote control unit 7Connection for control cable from power

source or cooling unit

3Connection BLUE, with ELP* for coolant to

the welding gun

8Connection RED, for coolant to cooling

unit

4Connection RED, for coolant from welding

gun

9Connection for shielding gas

5Connection for welding gun 10 Connection BLUE, for coolant from cooling

unit

NOTE! Display (digital instrument) and coolant connections only available on certain models.

* ELP = ESAB Logic Pump, see point 5.2.

5.2 Water connection

The wire feed unit with water connection is equipped with a detection system ELP

(ESAB Logic Pump) which checks that the water hoses are connected. When

connecting a water--cooled welding gun, the water pump starts.

Detection only works with power sources that are equipped with ELP.

-- 9 --

bm50d1ea

5.3 Wire feed pressure

Start by making sure that the wire moves smoothly through the wire guide. Then

set the pressure of the wire feeder’s pressure rollers. It is important that the

pressure is not too great.

Fig 1 Fig 2

To check that the feed pressure is set correctly, you can feed out the wire against

an insulated object, e.g. a piece of wood.

When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed

rollers should slip.

If you hold the gun approx. 50 mm from the piece of wood, the wire should be

fed out and bend (fig. 2).

5.4 Replacing and inserting Feed 3004 wire

SOpen the side panel.

SDisconnect the pressure sensor by folding it backwards, the pressure rollers

slide up.

SIf necessary, roll back the wire and remove the wire bobbin.

SStraighten out the new wire 10--20 cm. File away burrs and sharp edges from the

end of the wire before inserting it into the wire feed unit.

SMake sure that the wire goes properly into the feed roller’s track and into the

outflow nozzle or wire guide.

SSecure the pressure sensor.

SClose the side panel.

5.5 Replacing and inserting Feed 4804 wire

SOpen the side panel.

SPress down and pull the pressure device towards you and up.

SPull out the bogie.

SIf necessary, roll back the wire and remove the wire bobbin.

SStraighten out the new wire 10--20 cm. File away burrs and sharp edges from the

end of the wire before inserting it into the wire feed unit.

SMake sure that the wire goes properly into the feed roller’s track and into the

outflow nozzle or wire guide.

SReinstall the bogie.

SClose the side panel.

-- 1 0 --

bm50d1ea

5.6 Changing feed rollers on Feed 3004

SOpen the side panel

SDisconnect the pressure sensor (1) by folding it

backwards.

SDisconnect the pressure rollers (2) by turning the

axle (3) 1/4 turn clockwise and pulling out the axle.

The pressure rollers disconnect.

SDisconnect the feed rollers (4) by unscrewing the nuts

(5) and pulling out the rollers.

During installation, repeat the above in reverse order.

Choice of track in the feed rollers

Turn the feed roller with the dimensioning mark for the

required track towards you.

5.7 Changing feed rollers on Feed 4804

SOpen the side panel.

SPress down and pull the pressure device (1) towards

you and up.

SPull out the bogie (2).

SUndo the socket head cap screws (3) on the holder

for the intermediate nozzle and remove it.

SUndo the screw for the outflow nozzle (4) and

push back the nozzle.

SCompletely undo the socket head cap screw (5) in the

centre.

SUndo the two outer socket head cap screws (6) 1/2 a

turn.

SPull out the feed rollers (7).

During installation, repeat the above in reverse order.

Choice of track in the feed rollers

Place no, one or two driving washers

between the outer washer and the feed

roller. NOTE! When replacing the

pressure rollers (8), the entire bogie is

replaced.

Andere Handbücher für Aristo Origo Feed 3004

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB Caddy 140 Bedienungsanleitung

ESAB

ESAB Rogue Series Bedienungsanleitung

ESAB

ESAB Renegade EC 1000 Bedienungsanleitung

ESAB

ESAB Origo Mig C170 3ph Bedienungsanleitung

ESAB

ESAB EPP-200 Bedienungsanleitung

ESAB

ESAB OrigoFeed 30-4 Bedienungsanleitung

ESAB

ESAB Versotrac EWT 1000 Bedienungsanleitung

ESAB

ESAB Powercut 875 Bedienungsanleitung

ESAB

ESAB EMP235ic Bedienungsanleitung

ESAB

ESAB Rogue EMP 210 PRO Bedienungsanleitung

ESAB

ESAB Rogue ES 150i Bedienungsanleitung

ESAB

ESAB Rogue EM 125 Bedienungsanleitung

ESAB

ESAB Thermal Dynamics CUTMASTER 40 Bedienungsanleitung

ESAB

ESAB Caddy Series Bedienungsanleitung

ESAB

ESAB Aristo Arc 4000i Bedienungsanleitung

ESAB

ESAB LKA 180 Bedienungsanleitung

ESAB

ESAB Fabricator ET 410iP Bedienungsanleitung

ESAB

ESAB Aristo Mig 5000iw WeldCloud Bedienungsanleitung

ESAB

ESAB Caddy Tig 2200iw Bedienungsanleitung

ESAB

ESAB Multimaster 260 Bedienungsanleitung

ESAB

ESAB MobileFeed 301 AVS Bedienungsanleitung

ESAB

ESAB ARC400i Bedienungsanleitung

ESAB

ESAB Aristo Mig 5000i Bedienungsanleitung

ESAB

ESAB A6 Mastertrac Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung