ESAB MEK 4C Bedienungsanleitung

Valid from Serial NO 623-- XXX--XXXX

456 679-- 001 97.01.15

MEK 4C

101103105107109111102021110025108024042106023061104022041100020040060001

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Instruction manual

Betriebsanweisung

Manuel d’instructions

Gebruiksaanwijzing

Instrucciones de uso

Istruzioni per l’uso

Manual de instruções

Ïäçãßåò ÷ñÞóåùò

-- 2 --

Rätt till ändring av specifikationer utan avisering förbehålles.

Ret til ændring af specifikationer uden varsel forbeholdes.

Rett til å endre spesifikasjoner uten varsel forbeholdes.

Oikeudet muutoksiin pidätetään.

Rights reserved to alter specifications without notice.

Änderungen vorbehalten.

Sous réserve de modifications sans avis préalable.

Recht op wijzigingen zonder voorafgaande mededeling voorbehouden.

Reservado el derecho de cambiar las especificaciones sin previo aviso.

Specifiche senza preavviso.

Reservamo--nos o direito de alterar as especificações sem aviso prévio.

Äéáôçñåßôáé ôï äéêáßùìá ôñïðïðïßçóçò ðñïäéáãñáöþí ×ùñßò ðñïåéäïðïßçóç.

SVENSKA 3..............................................

DANSK 10................................................

NORSK 17................................................

SUOMI 24................................................

ENGLISH 31..............................................

DEUTSCH 38.............................................

FRANÇAIS 45.............................................

NEDERLANDS 52.........................................

ESPAÑOL 59..............................................

ITALIANO 66..............................................

PORTUGUÊS 73..........................................

ÅËËÇÍÉÊÁ 80.............................................

ENGLISH

TOCe -- 3 1 --

1 DIRECTIVE 32........................................................

2SAFETY 32...........................................................

3 INTRODUCTION 33...................................................

3.1 TECHNICAL SPECIFICATION 33..............................................

4 INSTALLATION 33....................................................

5 OPERATION 34.......................................................

5.1 CONNECTION 34............................................................

6 MAINTENANCE 35....................................................

6.1 INSPECTION AND CLEANING 35..............................................

7 ORDERING OF SPARE PARTS 35......................................

8 ACCESSORIES 36....................................................

9 WEAR COMPONENTS 37..............................................

LIST OF COMPONENTS 88............................................

DIAGRAM 89.........................................................

SPARE PARTS LIST 90................................................

-- 3 2 --

bm19d12e

1 DIRECTIVE

DECLARATION OF CONFORMITY

Esab Welding Equipment AB, S--695 81 Laxå, Sweden, gives its unreserved guarantee that

Wire feed unit MEK 4C from serial number 623 complies with standard EN 60974--1, in ac-

cordance with the requirements of directive 73/23/ EEA and addendum 93/68/ EEA and

standard EN 50199 in accordance with the requirements of directive 89/336/ EEA and ad-

dendum 93/68/ EEA.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

Paul Karlsson

Managing Director

Esab Welding Equipment AB

695 81 LAXÅ

SWEDEN Tel: + 46 584 81000 Fax: + 46 584 12336

Laxå 97--01--15

2SAFETY

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to keep fumes and gases from your breathing zone and

the general area.

ARC RAYS -- Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

SProtect your ears. Use ear defenders or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

-- 3 3 --bm19d12e

3 INTRODUCTION

The MEK 4C is an encapsulated wire feed unit with four roller feed.

The unit provides space for a 300 mm diameter wire reel and has a built--in

positioner.

For a wire feed unit to be complete it must be equipped either with a turnable,

counterbalance device or a carriage. A turnable or counterbalance device allow the

wire feed unit to be mounted on a pivot on the power source. A carriage allows the

wire feed unit to be moved easily over the floor or work table.

A wire feed unit and turnable or carriage can also be fitted with a support device and

suspended over the work place.

3.1 TECHNICAL SPECIFICATION

Dimensions lxwxh 630x245x490 mm

Weight 15 kg

Wire feed speed 1,9--25 m/min

Voltage 42 V 50--60 Hz

Power consumption 300 VA

Torch connection EURO

4 INSTALLATION

WARNING

This product is intended for industrial use. In a domestic environment this prod-

uct may cause radio interference. It is the users responsibility to take adequate

precautions.

-- 3 4 --

bm19d12e

5 OPERATION

5.1 CONNECTION

1. Nipple, cooling water (only certain models)

2. Nipple, gas connection

3. Connector, control cable

4. Adapter, welding current

5. Connector, remote control (activated automatically on connection of remote)

6. Nipple, cooling water (only certain models)

7. Adapter, welding torch

8. Connector setting control

23 4

IMPORTANT!

To prevent the reel sliding off the hub: Lock the reel in place

by turning the red knob as shown on the warning label atta-

ched next to the hub.

-- 3 5 --bm19d12e

6 MAINTENANCE

6.1 INSPECTION AND CLEANING

Regularly maintenance is important for reliable and safe operations.

SCleaning and replacement of the wire feed mechanism’s wear parts should take

place periodically to ensure trouble free wire feed.

Note that an excessive pressure setting can result in abnormal wear on the

pressure roller, feed roller and wire liner

STorch

Regulary blow the wire liner and clean the gas shroud.

WARNING!

Rotating parts can cause injury, take

great care.

7 ORDERING OF SPARE PARTS

When ordering spare parts please specify the machine model, serial number and the

designation and order numbers of parts as shown in the list of spare parts. This sim-

plifies dispatch and ensures correct delivery.

-- 3 6 --

bm19d12e

8 ACCESSORIES

0456 528 880 L=1,7m

0456 528 885W L=1,7m

0469 789 880

0469 786 880 0156 654 893

0456 693 880

0469 792 881

There is a risk of tipping if the wire feed cabinet is fitted with a counterbalance arm.

Secure the equipment, especially if used on an uneven or sloping surface.

Limit the angle of rotation of the wire feed cabinet using the straps supplied.

When moving the equipment, do NOT pull on the torch.

WARNING!

-- 3 7 --bm19d12e

9 WEAR COMPONENTS

Pos Design. Order no. Wire Ø Type

1Feed roller 0369 557--001 0.6--0.8 A,B

Feed roller 0369 557--002 0.8--1.0 A,B

Feed roller 0369 557--003 1.0--1.2 A,B

Feed roller 0369 557--004 1.0--1.2/1.4--1.6 D

Feed roller 0369 557--005 1.4--1.6 (2.0--2.4) D

Feed roller 0369 557--006 1.0--1.2 C

Feed roller 0369 557--007 1.2--1.6 A,B

Feed roller 0369 557--008 1.6 C

2Pressure roller 0369 728--001

P.r. (knurled) 0466 262--001

3Adapter 0455 053--880

4Inlet nozzle 0455 049--001

5Adapter nozzle 0455 072--001

6Outlet nozzle 0469 837--880

Outlet nozzle 0469 837--881

7Pinion 0455 052--001

A=Fe ,B=Ss,C=Al.,D=Tubewire

bm11d003

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB Tig 4000i Aristo Bedienungsanleitung

ESAB

ESAB RobustFeed AVS Bedienungsanleitung

ESAB

ESAB AristoFeed 30 Bedienungsanleitung

ESAB

ESAB Caddy Arc 152i Bedienungsanleitung

ESAB

ESAB PowerCut 1600 Bedienungsanleitung

ESAB

ESAB Fabricator 252i Bedienungsanleitung

ESAB

ESAB OCF 2L Bedienungsanleitung

ESAB

ESAB Cadd Tig 1500i TA34 Bedienungsanleitung

ESAB

ESAB Aristo Origo Feed 3004 Bedienungsanleitung

ESAB

ESAB Retrofit Aristo Mig 4004i WeldCloud Bedienungsanleitung

ESAB

ESAB EMP 215ic Bedienungsanleitung

ESAB

ESAB CaddyTig HF Bedienungsanleitung

ESAB

ESAB A22 POB Gebrauchsanweisung

ESAB

ESAB AK 400 Bedienungsanleitung

ESAB

ESAB ESP-50 Bedienungsanleitung

ESAB

ESAB Origo Mig C420 PRO Bedienungsanleitung

ESAB

ESAB ARC250i Bedienungsanleitung

ESAB

ESAB ST-21 Bedienungsanleitung

ESAB

ESAB A2SF J1 Bedienungsanleitung

ESAB

ESAB Aristo Origo Feed 3004 Bedienungsanleitung

ESAB

ESAB EMP 205ic AC/DC Bedienungsanleitung

ESAB

ESAB CIGWELD WeldSkill 185LCD Bedienungsanleitung

ESAB

ESAB Caddy 150 Bedienungsanleitung

ESAB

ESAB Aristo WeldCloud Mig U5000i Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung