ESAB Railtrac B42V Bedienungsanleitung

Instruction manual

0463 465 001 GB 20161102 Valid for: 1634-xxx-xxxx

Railtrac™ B42V

TABLE OF CONTENTS

0463 465 001 © ESAB AB 2016

1SAFETY ....................................................................................................... 4

1.1 Meaning of symbols ............................................................................... 4

1.2 Safety precautions ................................................................................. 4

2INTRODUCTION.......................................................................................... 7

2.1 Technical data......................................................................................... 11

3INSTALLATION............................................................................................ 12

3.1 Connections............................................................................................ 12

3.2 Assembly ................................................................................................ 12

4OPERATION ................................................................................................ 14

4.1 Preheat .................................................................................................... 14

4.2 Remote control for digital wire feeder.................................................. 14

4.3 Electronic – Carriage ............................................................................. 15

4.4 Remote control ....................................................................................... 17

5MAINTENANCE........................................................................................... 18

6SPARE PARTS ............................................................................................ 19

ORDERING NUMBERS....................................................................................... 20

ACCESSORIES ................................................................................................... 21

Rights reserved to alter specifications without notice.

1 SAFETY

0463 465 001 -4- © ESAB AB 2016

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of

life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and Safety

Data Sheets (SDSs).

NOTE!

For product operation instructions please refer to the supplied USB memory stick.

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0463 465 001 -5- © ESAB AB 2016

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or work

cable around your body. Keep welding power source and cables as

far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0463 465 001 -6- © ESAB AB 2016

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be potential

difficulties in ensuring electromagnetic compatibility of class

A equipment in those locations, due to conducted as well

as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment and its implementation

in accordance with national law, electrical and/or electronic

equipment that has reached the end of its life must be

disposed of at a recycling facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved collection

stations.

For further information contact the nearest ESAB dealer.

ESAB can provide you with all necessary welding protection and accessories.

2 INTRODUCTION

0463 465 001 -7- © ESAB AB 2016

2 INTRODUCTION

Railtrac™ B42V is a system of components that can be configured to create the optimal

solution for your mechanized welding application. To minimise problems associated with

harsh environments, most mechanical parts are constructed in aluminium or stainless steel.

Railtrac™ B42V is designed for horizontal and vertical joints (up, and down, when

applicable).

Features Railtrac™ B42V

• 42VAC or battery driven with standard Makita® 18V system.

• High speed and low speed in one unit.

• Micro process controlled electronics package in a single onboard housing.

• Stepper motor both for drive and weaving function.

• Only one cable to the wire feeder (not needed if using the battery) and one cable to the

remote control (if used) but can be run without any remote control.

• The unit can be programmed and run directly from the controls on the Railtrac™

machine if the remote control is lost-damaged or not preferred.

• Dual high-visibility screens for easy viewing in any orientation.

• The remote is programmable for weave patterns and travel speed and is capable of

controlling voltage and wire feed speed in up to 5 standard programs.

• IP44 environmental rating on both the Railtrac™ and the remote control.

• Choose between welding on left side or right side for remote to correspond to carriage

movement.

Direct connection to all new modern ESAB wire feeders

Railtrac™ B42V can be easily connected to most ESAB wire feeders with no major

modification. Remote adapters have to be mounted in wire feeders (Aristo®Feed3004,

Aristo®Feed4804, Origo™Feed304, Origo™Feed484 and Warrior™Feed304).

Five programs can easily be stored

As many as five different programs can be stored. Each program is individual and can be

retrieved from the control on the main unit or the remote control.

Remote control of welding parameters and immediate program shift

Both welding current (wire-feed speed) and voltage can be adjusted (in %) during welding.

Stepping up or down between the alternative motion programs is also easy, depending on

welding position.

Resilient programming units with great potential

Straightforward, logically-designed programming units are used to set the values for five

different programs. All speeds are calibrated in millimetre (mm), for the greatest possible

precision and welding quality.

Remote control for the harshest environments

Using the robust and lightweight remote control that comes with the Railtrac™ B42V, the

operator can access and control every function without lifting the welding visor. Individually

shaped buttons for:

• Start and stop

• Shift program

• Travel or welding direction (cutting direction)

• Travel or welding speed (cutting speed)

• Weaving width

• Zero-line displacement

2 INTRODUCTION

0463 465 001 -8- © ESAB AB 2016

• Welding current (wire-feed speed)

• Welding voltage

Joint rail system for stiff or flexible rail applications

The extendable Railtrac™ combi-rail enables the same tractor to run on a flexible rail or the

same rail stiffened with a stiffener bar. The stiffener-bar rail fits into the existing holes in the

rail. This makes it possible to weld straight as well as curved surfaces (min 1600mm in

diameter). The combi-rail is clean, without a rack for driving the tractor. If longer rails are

needed it is easy to joining several rails.

2 INTRODUCTION

0463 465 001 -9- © ESAB AB 2016

1. Slide height adjustment 7. Locking wheel

2. Support wheel holder 8. Locking screw

3. Bracket for coarse adjustment in/out and

height

9. Electronics

4. Universal torch holder 10. Battery holder

5. Protection plate 11. Weaving movement

6. Drive wheel ×2 12. Weaving movement connection

2 INTRODUCTION

0463 465 001 - 10 - © ESAB AB 2016

Dimensions

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB Powercut 875 Bedienungsanleitung

ESAB

ESAB EMP 215ic Bedienungsanleitung

ESAB

ESAB ES 180i Bedienungsanleitung

ESAB

ESAB Aristo WeldCloud Mig U5000i Bedienungsanleitung

ESAB

ESAB MT-450W Bedienungsanleitung

ESAB

ESAB Miggytrac B501 Bedienungsanleitung

ESAB

ESAB Fabricator ET 410iP Bedienungsanleitung

ESAB

ESAB Multimaster 300 Bedienungsanleitung

ESAB

ESAB Precision Plasmarc IEFC-S PT-24 Bedienungsanleitung

ESAB

ESAB LAF 631 Bedienungsanleitung

ESAB

ESAB Miggytrac B501 Bedienungsanleitung

ESAB

ESAB Caddy Tig 1500i VRD Bedienungsanleitung

ESAB

ESAB Warrior 750i CC/CV Bedienungsanleitung

ESAB

ESAB PCM-1125 Bedienungsanleitung

ESAB

ESAB Migmaster 275 Bedienungsanleitung

ESAB

ESAB A6 Mastertrac Bedienungsanleitung

ESAB

ESAB Aristo Origo Feed 3004 Bedienungsanleitung

ESAB

ESAB Rogue Series Bedienungsanleitung

ESAB

ESAB A2 Multitrac Bedienungsanleitung

ESAB

ESAB Origo Mig C170 3ph Bedienungsanleitung

ESAB

ESAB LKA 150 Bedienungsanleitung

ESAB

ESAB Aristo 500ix Bedienungsanleitung

ESAB

ESAB A6 DK Bedienungsanleitung

ESAB

ESAB Warrior 400i CC/CV Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung