ESC EPC-600-ST Bedienungsanleitung
2
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
To alert the user to the presence of un-insulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
The presence of important operating and maintenance (servicing) instruction in
the literature accompanying the product
WARNING
CAUTION
3
FCC COMPLIANCE STATEMENT
FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE
LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE
LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT
INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A
RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER
WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
CE COMPLIANCE STATEMENT
WARNING
THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO
INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.
4
•FEATURES -------------------------------------------------------------------------- 5
•CONSTRUCTION ------------------------------------------------------------------ 6
•DIP SWITCH SETTING ----------------------------------------------------------- 7
-Communication
-Protocol
- PTZ address
•CABLE CONNECTION ---------------------------------------------------------- 9
•MAIN SETUP MENU ------------------------------------------------------------ 11
(1) Motion Setting ----------------------------------------------------------------------- 11
Preset ------------------------------------------------------------- 11
Tour ------------------------------------------------------------ 12
Scan ------------------------------------------------------------ 13
Pattern ------------------------------------------------------------ 14
Alarm ------------------------------------------------------------ 15
Area ------------------------------------------------------------ 16
(2) Dome Setting --------------------------------------------------------------------- 17
(3) Camera Setting --------------------------------------------------------------------- 19
(4) Clear Data --------------------------------------------------------------------------- 20
(5) Vector Initialize --------------------------------------------------------------------- 20
USING KEYBOARD CONTROLLER ------------------------------------------- 21
SPECIFICATIONS ---------------------------------------------------------------- 27
DIMENSIONS ---------------------------------------------------------------------- 29
CONTENTS
5
FEATURES
•Builtin stabilizer to use vibration area or Military zone, etc - optional
•Fire engine, Police car and other special applications
•Built-in 27x Optical DayNight zoom camera and Endless PanTilt driver
•Aluminum body and resistance lens cover (Crystal)
•MAX. 100˚/sec Pan speed
•Builtin MPEG-4 / IP PTZ server to use plug-in & play by client PC by using LAN
or WAN Network line (TCP / IP)
•System function
Preset - Up to 63 programmable preset.
Scan - Repeatedly pan & tilt operating between two positions. (Max. 4)
Tour – Up to 8 programmable Tours consisting of presets with individual dwell time..
Pattern - Up to 2 programmable Patterns memorized the PTZ movement.
Area – Up to 4 programmable Area display set.
Alarm- Move the camera to programmed Preset position with Alarm trigger (Max. 2)
•Variable speed Pan/Tilt control
In manual mode, sophisticated operating is possible at zoom in state by speed correcting function.
•Position Auto Return (Park Action)
After passing some time at manual operating, returning to the pre-set position.
•OSD(On Screen Display)
Displays camera ID , area name, preset No.and kinds of camera functions on screen.
•Various Function Switch
1. Convertible to RS485 and RS 232C by DIP switch.
2. Protocol convert switch
By using DIP switch, P-D(2400bps), and P-P(4800bps) protocol can be converted and various
baud rate can be matched by auto detection.
3. Supports up to 255 address
6
CONSTRUCTION
7
DIP SWITCH SETTING
•System setting
NO 1,2. Communication Protocol Select
1:On/2:Off -> P-D , 1:Off/2:On -> P-P
NO 3,4,5,6. Reserved
NO 7. Video format select (NTSC/PAL), Keep this as factory default.
NO 8. Select mounting type. (Top mount/Ceiling mount)
On : Ceiling Mount / Off : Pole, Car roof, or desk mount.
•Camera Address Select
Refer to the next page(8-page) camera address setting
•Termination Resistance Switch
Whether it is a PT camera or keyboard controller, the device which is connected at the
end of the line must have the cable communication terminated by setting the
appropriate DIP switch. Without proper termination, there is potential for control signal
errors. Total length of the cable for communication should not exceed 1.2Km.
•RS-485 communication
RS-485 communication is used to control the PTZ camera. For multiple camera connection &
control, user should assign camera address through this DIP switch.
Standard : RS-485 with MAX. 256 Camera Control
Number of wire : 2 Wire (D+, D-)
Protocol : D-Protocol, P-protocol
•D Protocol ?
Baud Rate : 2400 bps
Data Format : Asynchronous, 1 start bit, 8 data bits, non parity, 1 stop bit
Topology : Daisy-chain
etc : Refer to -D Specification
Protocol and System Set
Camera Address Set
12345678
8
CAMERA ADDRESS SETTING
Address MSB LSB Address MSB LSB Address MSB LSB Address MSB LSB
- 0 0 64 4 0 128 8 0 192 C 0
1 0 1 65 4 1 129 8 1 193 C 1
2 0 2 66 4 2 130 8 2 194 C 2
3 0 3 67 4 3 131 8 3 195 C 3
4 0 4 68 4 4 132 8 4 196 C 4
5 0 5 69 4 5 133 8 5 197 C 5
6 0 6 70 4 6 134 8 6 198 C 6
7 0 7 71 4 7 135 8 7 199 C 7
8 0 8 72 4 8 136 8 8 200 C 8
9 0 9 73 4 9 137 8 9 201 C 9
10 0 A 74 4 A 138 8 A 202 C A
11 0 B 75 4 B 139 8 B 203 C B
12 0 C 76 4 C 140 8 C 204 C C
13 0 D 77 4 D 141 8 D 205 C D
14 0 E 78 4 E 142 8 E 206 C E
15 0 F 79 4 F 143 8 F 207 C F
16 1 0 80 5 0 144 9 0 208 D 0
17 1 1 81 5 1 145 9 1 209 D 1
18 1 2 82 5 2 146 9 2 210 D 2
19 1 3 83 5 3 147 9 3 211 D 3
20 1 4 84 5 4 148 9 4 212 D 4
21 1 5 85 5 5 149 9 5 213 D 5
22 1 6 86 5 6 150 9 6 214 D 6
23 1 7 87 5 7 151 9 7 215 D 7
24 1 8 88 5 8 152 9 8 216 D 8
25 1 9 89 5 9 153 9 9 217 D 9
26 1 A 90 5 A 154 9 A 218 D A
27 1 B 91 5 B 155 9 B 219 D B
28 1 C 92 5 C 156 9 C 220 D C
29 1 D 93 5 D 157 9 D 221 D D
30 1 E 94 5 E 158 9 E 222 D E
31 1 F 95 5 F 159 9 F 223 D F
32 2 0 96 6 0 160 A 0 224 E 0
33 2 1 97 6 1 161 A 1 225 E 1
34 2 2 98 6 2 162 A 2 226 E 2
35 2 3 99 6 3 163 A 3 227 E 3
36 2 4 100 6 4 164 A 4 228 E 4
37 2 5 101 6 5 165 A 5 229 E 5
38 2 6 102 6 6 166 A 6 230 E 6
39 2 7 103 6 7 167 A 7 231 E 7
40 2 8 104 6 8 168 A 8 232 E 8
41 2 9 105 6 9 169 A 9 233 E 9
42 2 A 106 6 A 170 A A 234 E A
43 2 B 107 6 B 171 A B 235 E B
44 2 C 108 6 C 172 A C 236 E C
45 2 D 109 6 D 173 A D 237 E D
46 2 E 110 6 E 174 A E 238 E E
47 2 F 111 6 F 175 A F 239 E F
48 3 0 112 7 0 176 B 0 240 F 0
49 3 1 113 7 1 177 B 1 241 F 1
50 3 2 114 7 2 178 B 2 242 F 2
51 3 3 115 7 3 179 B 3 243 F 3
52 3 4 116 7 4 180 B 4 244 F 4
53 3 5 117 7 5 181 B 5 245 F 5
54 3 6 118 7 6 182 B 6 246 F 6
55 3 7 119 7 7 183 B 7 247 F 7
56 3 8 120 7 8 184 B 8 248 F 8
57 3 9 121 7 9 185 B 9 249 F 9
58 3 A 122 7 A 186 B A 250 F A
59 3 B 123 7 B 187 B B 251 F B
60 3 C 124 7 C 188 B C 252 F C
61 3 D 125 7 D 189 B D 253 F D
62 3 E 126 7 E 190 B E 254 F E
63 3 F 127 7 F 191 B F 255 F F
10
Main Menu window will appear.
Main Menu
JOYSTICK
1 + Quick Operating Guide
Flip : 90 +
Auto Flip ON : 93 + 3sec.
Auto Flip OFF : 94 + 3sec.
Move initial position : 93 +
Menu Start : 95 +
MENU
<Pressing keypad “1” and holding the “MENU” key for approximately 3 seconds>
<or “ Press No.95 + Preset key ” to go into the set-up menu>
95 + PRESET
JOYSTICK
or NEAR
** Move the joystick up and down to navigate through the menu items.
Push the NEAR key or move joystick to the right to select a menu item.
or
PRESET
PRESET
PRESET
PRESET
PRESET
Main Setup-menu
MAIN MENU
---------
MOTION SETTING ▶
DOME SETTING ▷
CAMERA SETTING ▷
CLEAR DATA ▷
VECTOR INIT
EXIT
SELECT→NEAR/RIGHT ▷ SUB MENU
MOTION MENU
-----------
PRESET ▶
TOUR ▷
SCAN ▷
PATTERN ▷
ALARM ▷
AREA ▷
BACK
EXIT
SELECT→NEAR/RIGHT ▷ SUB MENU
DOME MENU
-----------
TITLE SET : CPAN 20.011
AUTO FLIP ON
POWER UP ACTION ON
PARK ACTION ▷
DISPLAY ON/OFF ▷
SPEED BY ZOOM ON
FACTORY SET ▷
BACK
EXIT
SELECT→NEAR/RIGHT
CAMERA MENU
-----------
FOCUS MODE ▶
WHITE BALANCE ▷
EXPOSURE ▷
DAY & NIGHT : DAY
SHARPNESS : 10
BACKLIGHT : OFF
CAMERA DEFAULT
BACK
EXIT
SELECT→FOCUS MODE SETTING
DATA CLEAR
--------------------
PRESET
TOUR
AREA
ALARM
SCAN
PATTERN
BACK
EXIT
SELECT→NEAR/RIGHT
Inhaltsverzeichnis
