ESI AC64v Bedienungsanleitung

Page 1of 13 0455-0322 Rev A

eSIP and eCloud

AC64v Access Device Quick Install Guide

This guide instructs on installation and basic door unlocking settings of the ESI AC64v Access Device.

Page 2of 13 0455-0322 Rev A

Package Contents

Physical Specifications

Model

Device size

AC64v

7 x 3.47 x 1.43 inches (177.4 x 88 x 36.2 mm)

Front Panel

Page 3of 13 0455-0322 Rev A

Wiring Interface

Open the rear case of the device, there is a row of terminal blocks for connecting the power supply,

electric lock control, etc. The connections are as follows:

Reference

Number Description

1 Ethernet interface: standard RJ45 interface, 10/100M adaptive, Cat5e network cable or

better is recommended.

2 Two sets of short-circuit input detection interfaces: for connecting switches, infrared

probes, door magnets, vibration sensors and other input devices.

3 Wiegand interface.

4 RS485 interface.

5 Power interface: 12V/1A input up positive, down grounded.

6, 7 Two sets of short-circuit output control interface: used to control electric locks, alarms,

etc.

8 Line out interface.

Page 4of 13 0455-0322 Rev A

Wiring Instructions

NO: Normally Open Contact

COM: Common Contact

NC: Normally Close Contact.

Driving Mode Electric Lock Mode

Connections

Passive

No electrical

path when

open

Electrical

path when

open

√√

Electric lock (normally open type)

No electrical path to open door.

√√

Electric lock (normally closed type)

Electrical path to open door.

√√

Electric lock (normally open)

No power to open door.

Page 5of 13 0455-0322 Rev A

Installation Diagram

Panel Main Body Back Shell Wall Bracket

Wall mounting

Step 1: Installation preparation

• Check the following contents:

oKM3*6 screws x3

oTA4*30mm screws x5

o6*30mm screw anchors x5

oPM4*16mm screw x3

oTM6#*20/ screw x3

• Tools that may be required:

oPhillips screwdriver, hammer, RJ45 crimper

oElectric impact drill with an 8mm drill bit

Step 2: Drilling

1. Place the mounting template with dimensions on the surface of a wall in a desired flat position.

2. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill

about 50mm deep. Remove the template when finishing drilling.

3. Push or hammer screw anchors into the drilled holes

Page 6of 13 0455-0322 Rev A

Step 3: Removing hanging bracket and back shell.

Detach the wall bracket downward from the device and loosen the four screws on the rear cover using a

screwdriver, as shown below.

Step 4: Install the wall bracket, wiring and casing

1. Align the screw holes of the wall bracket with the holes in the wall and fix them to the wall with the

TA4*30mm screws, as shown below.

Page 7of 13 0455-0322 Rev A

2. Pass all the wires through the silicone plug in the middle of the bottom case. All lines should be

reserved for 15~20CM length, as shown below.

Note: The outlet hole of the bottom case faces down

3. Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in

connectors description (refer to Section 2).

4. Connect the terminal of the wired cable to the motherboard socket. Refer to wiring interface.

5. Test whether there is electricity by doing the following: Press the # button for 3 seconds to get the IP

address of intercom by voice. Input access password or press the indoor switch to verify that electric

lock functions.

6 Attach the device to the wall bracket in a top-down manner, locking the screws at the bottom, as

shown below.

Page 8of 13 0455-0322 Rev A

Flush mounting

Step 1: Installation preparation

• Check the following contents:

oPM3*3mm screws x5

oPM3*4mm screws x5

o6*30mm screws anchors x5

oKB3*10mm screws x3

oTA4*30mm screws x5

• Tools that may be required:

oPhillips screwdriver, hammer, RJ45 crimper

oElectric impact drill with an 8mm drill bit

oDrywall saw

Flush mounting the device requires a box to be recessed into the wall as shown in the diagram below.

Finished Appearance

Exploded view

Decoration

panel

Small Stents

Access

Device

Wall box

Page 9of 13 0455-0322 Rev A

Accessing Web Interface

Getting IP Address

1. Power on device and wait for it to boot (about 30 seconds). Long press DSS key for 3 seconds.

2. When the speaker beeps rapidly, press the speed-dial button within 5 seconds.

The device will announce the IP address by voice.

In addition, the device can switch IP address acquisition mode (Static vs DHCP mode):

1. Press and hold the speed-dial button for 3 seconds.

2. Wait for the speaker to beep, and then press the speed-dial button three times within 5 seconds.

The device will announce the IP address by voice after successfully switching to the network mode.

Settings

Step 1: Log in the access device

Input IP address (e.g. http://192.168.1.128) into address bar of PC’s web browser. For eSIP, default user

and password are admin/admin. For eCloud, default user and password are admin/SIPstn@ESI.

Step 2: Add the SIP account.

Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters.

Select “Activate”, and then click Apply to save this setting.

Page 10 of 13 0455-0322 Rev A

Step 3: Setting DSS key

Set the DSS key as shown below for a quick start. Click “Apply” to save this setting. Type: Memory Key.

Number 1: The DSS Key will dial to this Number 1.

Number 2: If Number 1 is unavailable, it will be forwarded to Number 2. Line: Working line.

Subtype: Speed dial

Step 4: Access Device Setting

Inhaltsverzeichnis

Andere ESI IP-Zugriffskontrollsysteme Handbücher

ESI

ESI A64v Bedienungsanleitung

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken

ZKTeco

ZKTeco SpeedFace-V5L Bedienungsanleitung

Jantar

Jantar REX A-1-9 Bedienungsanleitung

2N Access Unit Merkblatt

Kedacom

Kedacom KSCA120 Series Bedienungsanleitung

H3C

H3C WX2880X Bedienungsanleitung

G4S

G4S S870-EX Leitfaden

PRASTEL

PRASTEL M2000PE Bedienungsanleitung

Allegion

Allegion interflex IF-281 Cylinder Bedienungsanleitung

TECOM

TECOM TS1067E Bedienungsanleitung

Fermax

Fermax Memokey 100C Benutzerhandbuch

Fermax

Fermax CITYLINE MEMOKEY Bedienungsanleitung

Software House

Software House iSTAR Pro 2U RM Bedienungsanleitung

AKCP

AKCP SP+ Bedienungsanleitung

Bpt

Bpt HNA/102 Bedienungsanleitung

Civintec

Civintec CV9601T-T-1F Bedienungsanleitung

BioMax

BioMax N-X90W Bedienungsanleitung

ZKTeco

ZKTeco OP-200 Bedienungsanleitung

FingerTec

FingerTec s-Kadex Bedienungsanleitung