ESP EZ-PROX Bedienungsanleitung

EZ-PROX

SINGLE DOOR PROXIMITY DOOR ENTRY

USER MANUAL

Cont nts

Equipm nt r quir d for controlling on door:

12 volt DC power supply 2 amp minimum (EV-BPS)

ock - Magnetic (EVM -250)/Yale type keep 12 volt lock (enter D)

Push to exit button (EVEXIT)

Green break glass emergency release (EVEBG)*

*Note:- for use with Magnetic lock only

Functions of th EZ-PROX

The EZ-PROX can control one door by use of tags.

Programmable door open time 00 to 99 seconds.

1000 Tags can be programmed.

Door closed function (contact required).

Programmable rear tamper.

Internal buzzer for tamper monitoring (auto cut off after 1 minute).

10 x Tags Security Torx Tool

EZ-PROX and back plate EZ-PROX programmer

Screw

Screw anchor

Back cover

Hole

Indicator

114mm

75mm

Bell button

Remote control

IR sensor

Sighting Of Th EZ-PROX

The EZ-PROX must not be located within 2 meters of any

reader/keypad type devices.

The EZ-PROX must not be sited back to back with reader/keypad

type devices.

Site the EZ-PROX within easy access to the door/doors to be

controlled

Fitting

Using the template mark and drill the fixing and cable entry holes.

Remove security screws from the underside of the reader and

remove back plate.

Fit and secure the back plate in its final position. (See Fig below)

Feed the cable from the reader though the centre hole of the back

plate.

Clip the top of reader onto the back plate and secure using the

security fixing screws located on the underside of the reader.

Make all wiring connections and connect 12 volts DC to the reader.

The power ED will now be illuminated on the front of the reader.

05D390K

DC input +12V - +24V

AC input ~ 12V - 24V

Red-power DC input +12V - +24V

Black-power AC input ~ 12V - 24V

Brown-door status detecting reed switch

Orange-push to exit button

Yellow-DATA 1

Green-GND

Blue-Door bell

Purple-Door bell

Gray-DATA 0

White-NO 1

Pink-COM 1

Aqua-NC 1

Shielded ground

DATA 1

NO 1

COM 1

NC 1

DATA 0

Shielded ground

Red

Black

Brown

Orange

Yellow

Green

Blue

Purple

Gray

White

Pink

Aqua

Wiring Diagram

RED

BLACK

WHITE

PINK

Exit Button

0-20

L N

E.lock

+ -

DC out

+ -

Push button

GND P.B

N.O

Timer

secs

240vAC

INPUT

EV-BPS

Yale Release

Exit Button

0-20

L N

E.lock

+ -

DC out

+ -

Push button

GND P.B

N.C

Timer

secs

RED

BLACK

WHITE

PINK

INPUT

EV-BPS

Maglock

Emergency

door release

COM

N.C

Capacitor

0.47uF

100v

240vAC

Wiring Diagram for Maglock

Wiring Diagram for Yal R l as

How to nt r programing mod

Factory default programming code is 1234.

Input the programming code twice (1234 and1234), the yellow

ED will be on. To exit programming mode press # button.

Programming a fob or card

Note:- Do not have Tags in your hand or close by when pressing

keys.

EZ-PROX has 1000 locations available from 000 to 999.

1. Enter programming mode the blue ED will turn yellow.

2. Enter the location you want to programme the Tag to in a 3

digit format (xxx). A green light will show the location is empty

and ready to present a tag if a red light is present this location

is already in use. To delete this location press the star * key

twice. The ED will now turn green.

3. Pick up one Tag only and present it to the bottom of the reader

( ) and remove. A bleep will be heard this means the card or fob

is added. If further Tags are to be programmed select the next

available location number (xxx)

D l t ing a fob or card

Enter programing mode.

Enter any 3-digit number from 000 to 999 (yellow light will blink

during this process): if the ED changes to red there is data stored,

green shows the location is empty. Press * twice to delete the

stored location.

Press # to quit setting mode.

Programing a group of fobs or cards

Enter programing mode.

1. All tags to be programed as a group must have consecutive

numbers.

2. Press the * key then the 9 key the yellow light will flash

3. Press the 0 key then the 1 key the unit will bleep once.

4. Enter the number of the first available location in the range of

000 to 999.

5. Now enter in a 3 digit format how many tags you want to

programme (xxx) into the system, present the lowest number

tag to the reader ( ) and remove. Alternatively enter the 8 digit

number of the lowest number Tag from the group to be

programmed into the keypad.

To confirm the programming has been successful 2 bleeps will

be heard.

Press # to exit the setting mode.

S t door op n tim

1. Enter programming mode.

A ong bleep will be heard and the blue power ED will turn

yellow.

2. Press the * key then the 1 key the yellow ED will start to flash

3. Enter the time in seconds for the unlock time from 00 to 99

seconds.

Press # to exit the setting mode.

Th tamp r alarm

The built-in buzzer will sound a continuous Bleep Bleep. If the

photoresistor sensor is directly exposed to the light. The buzzer

will turn off automatically after 60 seconds, or when the light is

no longer detected, or by entering the programming code.

Changing th Programming cod

1. Enter programming mode.

A ong bleep will be heard and the blue power ED will turn

yellow.

2. Press * key followed by the 3 key the orange ED will start to

flash.

3. Enter the new programming pin twice.

A conformation bleep will be heard.

4. Press * 3 (yellow light blinks). Then input new administrator

code twice (The length of the new admin code must be the

same as the old one). Bleep - sound means it modifies

successfully.

Press # to exit the setting mode.

Turn on/off th r ar tamp r alarm

The rear tamper function consists of a photoresistor at the rear of

the unit. When this function is enabled the unit will emit a

continuous bleep if exposed to light.

The continuous bleep will stop automatically after 60seconds or if

the unit is no longer exposed to light.

You can cancel the continuous bleep by enter the programing

code.

1. Enter programming mode.

2. To turn on the rear tamper alarm.

Press * then 6 the yellow light will flash.

Press 0 then 2 the yellow light no longer flashes and the unit

will bleep.

Press # to exit the setting mode.

D l t all us r fobs and cards and r stor to

factory d fault

Enter programming mode.

1. A ong bleep will be heard and the blue power ED will turn

yellow.

2. Press * key followed by the 8 key theyellow ED will start to

flash.

3. Press the 8 key twice.

7 conformation bleeps will sound.

S t th (digit) l ngth of password

1. Enter programming mode by entering the 4 digit pin number

twice (default pin 1234).

A ong bleep will be heard and the blue power ED will turn

yellow.

2. Press the * key followed by 9 key the orange ED will now

flash.

3. Press 04 a long bleep will be heard.

4. Enter the length of the pin number you require (2,3,4,5 or 6).

If the length is the same as already programmed you will get a

conformation bleep.

If you have changed the length you will get 7 bleeps to say it has

now been changed.

Note:- Any pin numbers or Tags programmed into the system will

be deleted if the pin length is change.

Press # to exit the setting mode.

T chnical Sp cifications

Working temperature -10 ~ +55ºC

Voltage DC: 12V-24V AC: 12V~24V

Working current <120mA

Standby current <90mA

Card mode ID / IC card

Effective distance <5CM

Capacity 1000 Cards or Fobs

Elit S curity Products

Tel: 01527 515150

Fax: 01527 515143

email: info@espuk.com

Inhaltsverzeichnis

Andere ESP Gegensprechanlage Handbücher

ESP

ESP Enterview 3 Bedienungsanleitung

ESP

ESP aperta apkitao Bedienungsanleitung

ESP

ESP APKITKPGBLK Bedienungsanleitung

ESP

ESP EV4 Bedienungsanleitung

ESP

ESP Enterview Multi Bedienungsanleitung

ESP

ESP Enterview VX Bedienungsanleitung

ESP

ESP Enterview VX Bedienungsanleitung

ESP

ESP Aperta APKITKPBLK Bedienungsanleitung

ESP

ESP APWIFIDS2 Bedienungsanleitung

ESP

ESP APWIFIDS2 Bedienungsanleitung

ESP

ESP Enterview 3 Bedienungsanleitung

ESP

ESP Evoke Bedienungsanleitung

ESP

ESP Enterview MX EVMX2 Bedienungsanleitung

ESP

ESP Aperta APWIFIDS-BLK Bedienungsanleitung

ESP

ESP APKITG Bedienungsanleitung

ESP

ESP aperta EZTAG3 Bedienungsanleitung

ESP

ESP Aperta APMONWG Bedienungsanleitung

ESP

ESP Aperta APDSPXMW Bedienungsanleitung

ESP

ESP BDeye Bedienungsanleitung

ESP

ESP APWIFIDSBP2 Bedienungsanleitung

ESP

ESP Aperta APMONWG Bedienungsanleitung

ESP

ESP aperta EZTAG3 Bedienungsanleitung

ESP

ESP Enterview 5 Bedienungsanleitung

ESP

ESP Aperta APDSSW Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung

Bticino

Bticino Classe 300 Bedienungsanleitung

LG L5142 Bedienungsanleitung