ESP GuardCam LED Bedienungsanleitung

COMBINED SECURITY CAMERA LED FLOODLIGHT SYSTEM

GuardCam LED Manual.indd 1 11/01/2018 09:46:17

Table of contents

Contents of package .............................................. 2

Overview.........................................................3

Installation .......................................................5

Setting the date and time of GuardCam LED ..........................6

Insert/remove Micro SD Card .......................................7

Adjusting the Settings .............................................8

Viewing recorded files ............................................11

Technical Specifications ...........................................11

Contents of package

GuardCam LED

1 x Allen Key

2 x Screws

2 x Plastic Masonry Plugs 8GB Micro SD Card

User Manual

COMBINED SECURITY CAMERA LED FLOODLIGHT SYSTEM

GuardCam LED Manual.indd 2 11/01/2018 09:46:18

Overview

Installation

High power LED

PIR lens

Camera lens

FIG. 1 FIG. 2

IMPORTANT

IF IN ANY DOUBT ABOUT THE INSTALLATION OF THIS PRODUCT, CONSULT A QUALIFIED

ELECTRICIAN

- This product must be grounded

- Do not mount the unit against inflammable surfaces

- The motion detector will not operate correctly if it is installed:

• Near the outlet of a central heating boiler

• Near air conditioning plant

• Pointing directly at moving vehicles

• Within sight of reflections from moving water

• Where other lamps could shine on the detector

BEFORE ATTEMPTING ANY INSTALLATION OR MAINTENANCE, ENSURE THAT THE

ELECTRICAL SUPPLY IS SWITCHED OFF AND THE CIRCUIT FUSES REMOVED OR THE

CIRCUIT BREAKER IS IN THE OFF POSITION.

Please make sure the voltage and polarity are correct before connection. Incorrect voltage

may cause electric shock.

GuardCam LED Manual.indd 3 11/01/2018 09:46:18

Note: It is recommend to mount 2M above the ground for optimum performance, do not

mount the fixture below 1.2M. See below figure for details of performance range.

Detection range: 10M x 160°

GuardCam LED Manual.indd 4 11/01/2018 09:46:18

1. Place plastic masonry plugs into desired surface aligning holes as shown below. Using

an electric screwdriver, fasten mounting plate directly to surface using screws.

2. Feed the cable through the back mounting box and bush the cable entry to avoid

abrasion to the cable.

3. Wire the unit as follows: (Ensure all wires are connected securely and that no loose

strands are exposed)

4. Make sure the polarity is correct. Double check the connections after wiring. Errors may

damage the motion sensor or cause a fire hazard.

5. Attach the unit to the mounting plate. You will first need to angle the unit back so that

the catch at the top of the mounting plate fits into slot on the back of the unit. Next

lower the unit until holes at the bottom of the mounting plate and unit are flush. Then

screw (screw A) into this hole, tightening carefully.

Please allow 1 minute warm-up time after switching on.

* Push the RESET button after switching on.

Installing GuardCam LED

GuardCam LED Manual.indd 5 11/01/2018 09:46:18

After the file “userconfig.txt” is saved onto SD card, you should insert this SD card

immediately into the lighting no later than 2 minutes otherwise the time will be incorrect.

Setting the Date and Time:

GuardCam LED Manual.indd 6 11/01/2018 09:46:18

In order for the correct time & date to display on recorded files;

• Take the supplied micro SD card & place it in the SD / USB adaptor

• Place the adaptor in a spare USB port on PC / Laptop

• Go to web link - https://www.espuk.com/timesetup/

• The correct time & date will be displayed

Click ‘userconfig.txt’ to begin download, when complete, save the file to the micro SD

card location and re-insert into the GuardcamLED, the date and time will update automatically.

The file ‘userconfig.txt’ will be removed automatically.

Click “Generate Config’ to produce the “userconfig.txt” file

If the user can not connect to this link https://www.espuk.com/timesetup/

please follow these steps;

1. Open Notepad on computer;

- Input date and time (ex. 2019-01-02 09:33:33)

- Input “userconfig” as the file name

- Choose .txt for the format

- Save the file

2. Copy userconfig.txt to the root directory of SD card

3. Insert SD card into the card slot, the date and time will update automatically. The

file “userconfig.txt” will be remove automatically.

1. Unscrew the underside cover using provided Allen key , then insert the Micro SD card

until it automatically locks into place.

2. The Micro SD card is placed at the bottom of the motion sensor. To remove Micro SD

card, please push in SD once to eject, then pull out.

Insert/remove Micro SD Card:

GuardCam LED Manual.indd 7 11/01/2018 09:46:18

Time Control

Turn the time control to”+” side to increase the illumination time (7 minutes max.), turn

the control to “-“ side to reduce the illumination time (5 seconds min.).

Adjusting the Settings

Sensitivity Control

Adjust the detector range of Passive Infrared Motion Sensor (2M ~ 10M)

Selecting Working Mode:

Mode 1

- Light + camera + speaker: all day detection

- Daytime and nighttime: light, camera and speaker are all in operation

Mode 2

- Light at night + camera all day + speaker in the daytime

- Daytime: light is off, camera is on, speaker is on

- Nighttime: light is on, camera is on, speaker is off.

Mode 3

- Light at night + camera all day + speaker at night

- Daytime: light is off, camera is on, speaker is off.

- Nighttime: light is on, camera is on, speaker is on.

GuardCam LED Manual.indd 8 11/01/2018 09:46:18

Audio Mode

Pre-set default is“silent mode”, push one time for “pre-recorded message”,push again for

“dog barking”.

Push one more time for the message you just recorded.

Reset Button

Restores functions to default settings, press this button in case of system malfunction.

GuardCam LED Manual.indd 9 11/01/2018 09:46:18

Recording your own messages (see fig. 9)

Guardcam LED will allow you to record two messages of your own for delivery on

detection. To achieve a good quality playback it is best practice to make these recordings

prior to final installation speaking clearly in an environment free from background noise.

The microphone is located at the base of the unit directly above button A.

Two separate messages may be recorded for a maximum length of 10 seconds each.

To record a message press and hold button A. After the “bleep” release button A and

record your message. When finished press button A again to stop recording, you will here

a double confirmation bleep.

To record a second message simply repeat the process.

To check the recorded message/s press and release button B. Should you wish to delete a

self-recorded message press and hold button B for 3 seconds, a double

bleep will confirm deletion.

NB If you attempt to record a new message without first deleting an old message

you will hear a triple error bleep.

GuardCam LED Manual.indd 10 11/01/2018 09:46:18

Andere Handbücher für GuardCam LED

Inhaltsverzeichnis

Andere ESP Sicherheitskamera Handbücher

ESP

ESP IRCAM1000 Kurzanleitung

ESP

ESP SHDVC622VFBW Bedienungsanleitung

ESP

ESP IRCAM900 Pro Bedienungsanleitung

ESP

ESP GuardCamDeco Bedienungsanleitung

ESP

ESP FHDVC18PTZ Bedienungsanleitung

ESP

ESP Fort ECSPCAM Bedienungsanleitung

ESP

ESP REKIPC36FBW Bedienungsanleitung

ESP

ESP GuardCam LED Bedienungsanleitung

ESP

ESP IRCAM200Pro Bedienungsanleitung

ESP

ESP HDVC36FDW Bedienungsanleitung

ESP

ESP GuardCam LED Bedienungsanleitung

ESP

ESP FHDVC2812VFD Bedienungsanleitung

ESP

ESP REKHDC36FBG Bedienungsanleitung

ESP

ESP DECO GuardCam Bedienungsanleitung

ESP

ESP HDVC36FD Bedienungsanleitung

ESP

ESP PTZ10EXT Bedienungsanleitung

ESP

ESP DomeVF Pro Bedienungsanleitung

ESP

ESP GuardCamLED WIFI Bedienungsanleitung

ESP

ESP REKIPC36FDW Bedienungsanleitung

ESP

ESP GuardCamDeco Bedienungsanleitung

ESP

ESP GuardCam RF Bedienungsanleitung

ESP

ESP Recor HD REKHDC36FBG18P Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung