Essence Security EverGuard ES7000EG Bedienungsanleitung
Part of the Essence Group
ES7000EG
Version 1.7_01
December 2011
EverGuard
Control Panel
User Guide
© 2011 Essence Security International Ltd.
All rights reserved.
This document is the protected intellectual property of the Essence Security
International Ltd. Any copying, reprinting, reuse, reproduction ,adaptation
distribution or translation without the prior written permission of Essence Security
Ltd is prohibited.
The information included in this document is subject to change without notice.
For more information, please contact:
Essence Security
12 Abba Eban Avenue, Ackerstein Towers Bldg. D
Herzliya Pituach
46120 Israel
www.essence-grp.com
Tel: +972-73-2447777
Fax: +972-9-7729962
Table of Contents
EverGuard Control Panel
3
Table of Contents
1Overview ............................................................................................. 5
2Installation.......................................................................................... 6
2.1 ES7000EG Wall Mount.................................................................................6
2.2 GSM/GPRS Modem Installation................................................................... 11
2.2.1 GSM/GPRS Modem Components ..................................................... 11
2.2.1.1 GSM/GPRS Modem.......................................................... 11
2.2.1.2 Antenna and Coaxial Cable............................................... 12
2.2.1.3 GSM/GPRS Modem Connector .......................................... 12
2.2.2 Mounting the GSM/GPRS Modem Antenna........................................ 15
2.3 Inserting the SIM Card.............................................................................. 17
2.4 Connecting the Mini USB Cable .................................................................. 18
3Operation .......................................................................................... 20
3.1 About the ES7000EG Control Panel Equipment ............................................. 20
3.1.1 ES7000EG Hardware Front and Back Views...................................... 20
3.2 Buttons and Indications............................................................................. 23
3.2.1 ES7000EG Hardware Front and Back Views...................................... 23
3.2.2 Audible Indicators......................................................................... 24
3.2.3 Power Status ............................................................................... 25
3.2.4 Wireless Communication Status...................................................... 25
3.2.5 System Status ............................................................................. 26
3.2.6 Arm Status .................................................................................. 26
3.2.7 Open Zone Status......................................................................... 27
3.2.8 Call Guard function ....................................................................... 27
3.2.9 S.O.S function.............................................................................. 28
3.2.10 Monitoring Station Status .............................................................. 28
3.2.11 Detailed Operation and Modes........................................................ 29
3.2.11.1 The Arm Cycle................................................................ 29
3.2.12 Maintenance ................................................................................ 30
3.2.13 No Default ................................................................................... 30
3.2.14 Alarm 31
3.3 Optional Settings and Defaults ................................................................... 32
3.3.1 Atlas Mobile Application................................................................. 32
3.3.2 ESI-CMS Application ..................................................................... 42
Table of Contents
4
EverGuard Control Panel
3.3.2.1 Toolbar.......................................................................... 46
3.3.2.2 Status Bar ..................................................................... 47
3.3.2.3 Navigation Pane ............................................................. 47
3.3.2.4 Main Tab ....................................................................... 47
3.3.2.5 CMD Tab........................................................................ 48
3.3.2.6 Status Tab ..................................................................... 49
3.3.2.7 The control panel is divided into several parameter sets: ..... 50
4Maintenance ...................................................................................... 66
5FCC Radio frequency interference statement..................................... 67
6Specifications .................................................................................... 68
Overview
EverGuard Control Panel
5
1Overview
The ES7000EG is a two-way, wireless control panel unit comprising the main
element of the EverGuard Control Panel security system. This unit receives Radio
Frequency (RF) signals from a full array of sensors and detectors, remote access
devices and interface devices, such as a key fob and key pad. It also transmits
bidirectional RF signals to these units providing supervision, re-configuration,
control and more.
The control panel has RF and GSM jamming detection and reporting feature,
making it very hard to be tampered or hacked.
This user guide provides detailed information on installing, configuring and
operation of the ES7000EG security system.
For information on the initial setup of the ES7000EG Security System, defining
the peripherals and setting the initial parameters, refer to the Atlas Mobile section
3.3.1 below.
For information on modifying and updating the ES7000EG Control Panel
parameters, refer to the ESI-CMS section 3.3.2 below2.
Installation
6
EverGuard Control Panel
2Installation
2.1 ES7000EG Wall Mount
The ES7000EG can be mounted on a wall using the wall mount provided. In
addition, you must verify that there is adequate reception from the key pad
(ES700KPD) to the ES7000EG control panel and vice versa.
Note: The distance between the ES7000EG control panel and the
peripheral devices can be a maximum of 700 meters (2296 feet) (Open Air
Nominal) if there are no obstacles. The range can be augmented using the
ES700SOIR Repeater. (For more information on the ES700SIOR, refer to
the ES700SIOR User Guide.)
Mounting the ES700KPD requires the following components:
Drill with appropriate bit
Four (4) DIN 7982 cross recessed countersunk head tapping screws (4.2 x 40
mm)(not provided)
Standard appropriate screwdriver
To select a mounting location:
1. Find a suitable wall location:
Select a suitable location that is not too obvious, a secret or hidden
location that is not close to entry points, such as doors and windows.
The control panel must be located in an area that has good GSM signal
reception.
The control panel must be installed with a minimal distance of 20 cm
(0.66 ft) from users and nearby persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
The minimal installation height from the floor must be 70 cm (2.3 ft), and
at least 50 cm (1.65 ft) below the ceiling.
The control panel should be installed in a centric location, which means
centered between all the rooms and all the floors in the building.
The control panel should not be installed near:
High current electric appliances such refrigerators, washing
machines, electric or fuse boxes, etc.
Appliances such as cordless phones, TVs, which could cause
interference.
Heat sources such as stoves, radiators, or fireplaces, etc.
In any kind of metal enclosures like a metal cabinets or lockers.
2. Only after all the RF devices have been installed and tested, should the
installer mount the panel.
Installation
EverGuard Control Panel
7
In order to use the DVK RF test tool, the control panel location should be
selected first. The installer can then use the DVK tool to select the
location for all other devices.
To mount the ES7000EG control panel:
1. Identify a suitable location for the ES7000EG control panel according to the
guidelines above.
2. Remove the wall mount component from the ES7000EG control panel.
3. Place and hold the wall mount component on the desired mounting location.
Mark the desired drilling locations, using the four holes as shown below.
4. Using a drill with the appropriate drill bit, drill at the marked drilling locations.
5. Using the appropriate screwdriver, insert the four screws into the appropriate
locations on the wall mount component and secure them.
6. To open the ES7000EG control panel, use a large coin. Insert the coin into the
depression on the lower side of the panel. Twist the coin and the cover
separates from the main body.
7. On the ES7000EG control panel main body, create an opening for the power
cable by removing the punch-out according to the figure below.
Installation
8
EverGuard Control Panel
8. Attach the ES7000EG control panel to the wall mount, top first, then bottom
as shown in the figures below. ES7000EG control panel snaps into the
provided clips.
9. Using the appropriate screwdriver, insert the tamper screw and secure it in
place as shown in the figure below.
Installation
EverGuard Control Panel
9
WARNING! 220V Hazard! Make sure AC cable is disconnected before
applying the following sections
10. Measure distance end-to-end of power cable from the ES7000EG control
panel to the power source to ascertain that it is of sufficient length.
11. Insert the power cable through the punch-out opening and secure the wires
to the terminal block connectors as shown in the figure below.
Connect the ground wire to the middle terminal block connector.
Connect the Live and neutral wires to the first and third terminal block
connectors.
12. If the system configuration requires wireless communication, attach the
GSM/GPRS modem and antenna according to the
Installation
10
EverGuard Control Panel
GSM/GPRS Modem Installation instructions in section 2.2 below
13. Attach the top cover, top first, then, bottom as shown in the figure below.
14. Connect the other end of the power cable to a plug.
15. Insert the plug into the designated power socket. The wall mount and
installation are complete.
Inhaltsverzeichnis
