ETC QuickTouch+ Mk2 Bedienungsanleitung

ETC Installation Manual

QuickTouch+ Mk2 Control Panel and Electronics

Corporate Headquarters nMiddleton, WI, USA|+1 608 831 4116

New York, NY|Orlando, FL|Los Angeles, CA|Austin, TX|©2023 Electronic Theatre Controls, Inc.

Web etcconnect.com |Support support.etcconnect.com |Contact etcconnect.com/contactETC

Trademark and patent info: etcconnect.com/ip |Third-party license agreement info:etcconnect.com/licenses

Product information and specifications subject to change.ETCintends this document to be provided in its entirety.

8061M2110RevAReleased 2023-07

Overview

This guide provides information on installing the QuickTouch+ Mk2 control panel and electronics.

Back boxes must be installed prior to installing the control electronics and control wiring must be

run to the box. For information on installing back boxes, refer to the

QuickTouch Back Box

Installation Manual

that shipped with the back box.

Shipping Contents

• Control panel and electronics assembly with attached ground wire

• Two 8-position clamp-style connectors (one installed on the circuit board and one spare)

• One 8-position Emergency Stop terminator (installed on the circuit board)

• M4 x 8 mm screws (six for MK2 1CH and eight for MK2 6CH/12CH – each includes two spare

screws)

• Install Manual

Control Panel and Electronics

There are three QuickTouch+ Mk2 variants:

• QuickTouch+ Mk2 1 Channel controls a single channel and installs into a small back box

(8055A1100 or 8055A1102)

• QuickTouch+ Mk2 6 Channel and QuickTouch+ Mk2 12 Channel control six and 12 channels,

respectively, and install into a large back box (8055A1101 or 8055A1103)

QT+ MK2 1CH

1 2 3 4 5 6 7 8 9 10 11 12

QT+ MK2 12CH

1 2 3 4 5 6

QT+ MK2 6CH

SPEED

ETC Installation Manual

QuickTouch+ Mk2 Control Panel and Electronics

QuickTouch+ Mk2 Control Panel and Electronics Page 2 of 7 ETC

System Configuration

Before you install the control panel and electronics to the back box, you must terminate the

control wiring for your system. There are two connectors that ship installed in the back of the

electronics.

ABAB

QT+ MK2 1CH QT+ MK2 6CH/12CH

AMCX Connection

BE-stop Connection

Remove the clamp-style connectors from the board, as shown above (Mk2 1CH on the left and

Mk2 6CH/12CH on the right) before you terminate your wiring.

Use the following table to determine how to use the two control wiring connections and where

the cable should be routed based on your system configuration.

CAUTION: Do not exceed a maximum run length of 152 m (500 ft) of Ethernet

(Cat-5e or better) cable from the last E-stop button station on one end of the

system to the last Power and Distribution (PCD) box on the other end of the

system.

Connection Configuration Options

E-stop

Option 1: You have at least one external E-stop in your system. Run the cable from

here to the bottom connection on the first E-stop station in your system. Move the

termination jumper from here to the top connection on the last E-stop station in your

system.

Option 2: You have no external E-stop stations in your system. Leave the termination

jumper in this location.

MCX

Option 1: You have a Rigging System Power Injector (RSPI) powering your

QuickTouch+ controller. Run the cable from here to the bottom connection on the

RSPI.

Option 2: You do not have a RSPI powering your QuickTouch+ controller. Run the

cable from here to the Power and Control Distribution (PCD) electronics.

ETC Installation Manual

QuickTouch+ Mk2 Control Panel and Electronics

QuickTouch+ Mk2 Control Panel and Electronics Page 3 of 7 ETC

System Riser

E-stop Buttons

Up to 4 in a

chain

QuickTouch+ Mk2 Controller

Legend

MCX

E-stop

Rigging System

Power Injector

Rigging System Power Injector

For variable-speed motors

Power and Control

Distribution (PCD) boxes

Up to 12 motors

Power and Control

Distribution (PCD) boxes

Up to 12 motors

Optional

Remote Control

Terminate Wiring

Terminate your control cables for the E-stop and MCXconnectors before connecting them to the

headers on the electronics board.

• Use Cat 5e or better (Cat 6 or Cat 7)

• Use Shielded Twisted Pair (STP)cable

• Unshielded Twisted Pair (UTP) cable must be run in continuous grounded metal conduit

Note:

Installation must follow all national and local codes for electrical equipment.

The E-stop header on the electronics board ships with the termination jumper installed. If your

system does not have any external E-stop stations, leave the jumper installed. If you have external

E-stop stations, move the jumper to the last stop in the chain.

Control Wiring Diagram

The color code order of wires is the same for both motor communication (MCX) and E-stop,

though the data is different. Use the following diagram to determine the proper wiring order

when terminating the control wires.

W/BRN

W/ORG

ORG

W/GRN

W/BLU

Circuit

Board

Mount

BLU

GRN

BRN

+V (Supply)

D- (MCX Bus)

D+ (MCX Bus)

GND

Deadman

GND

E-stop

24V Supply

LED Supply

Deadman

E-stop Source

Smart

E-stop Monitor

GND

E-stop Return

MCX E-Stop

ES1

8 7 6 45 123

W/BLU

BLU

ORG

GRN

BRN

W/ORG

W/GRN

W/BRN

ETC Installation Manual

QuickTouch+ Mk2 Control Panel and Electronics

QuickTouch+ Mk2 Control Panel and Electronics Page 4 of 7 ETC

Terminate Cable to Connectors

Terminate the wires of your control cables according to the control wiring diagram and labels on

the connectors:

1. Label your cables (i.e. MCX, E-stop) and strip 40 mm (1.5 in) of the end of the outer cable

jacket using a sheathing tool or cutter, making sure not to damage the shield or insulation of

the inner conductors. If one of the conductors are damaged, cut the cable off squarely and

start over.

2. Fold the shield back to allow access to the conductors.

3. Fan out the wires in the appropriate order according to the Control Wire Diagram.

4. Strip the ends of each conductor 10 mm (0.4 in).

5. Insert the wires into the connector and verify the color coded order as shown on the

connector label

a. If you are using solid core wire, you can insert the conductor without pressing down on

the button.

b. If you are using stranded wire, you must use a 3 mm (1/8 in) small flatblade screwdriver to

press down the corresponding button on the connector and then insert the conductor.

5a. 5b.

Cat5/5e

Cat6/6a

MCX 1

40 mm (1.5 in)

10 mm (0.4 in)

Cat5/5e

Cat6/6a

MCX 1

Cat5/5e

Cat6/6a

3 mm

(1/8 in)

ETC Installation Manual

QuickTouch+ Mk2 Control Panel and Electronics

QuickTouch+ Mk2 Control Panel and Electronics Page 5 of 7 ETC

Install in Back Box

Once you have terminated your control cables to the connectors provided, you can finish installing

the control panel and electronics in the previously installed back box.

Provide Strain Relief for Controls Cables

Ensure that you run your cables through the strain relief points on your control electronics.

QT+ MK2 1CH

QT+ MK2 6CH/12CH

Strain relief points for QT+ MK2 1CH controllers can be adjusted using a Phillips screwdriver.

Strain relief for QT+ MK2 6CH/12CH controllers require a 4 mm hex driver. Depending on how you

run your cables, you might angle the strain relief for the 6CH/12CH electronics, as shown in the

image above.

Connect Controls Cables to Electronics

Connect the 8-position clamp connectors to the appropriate terminals (MCX, E-stop) on the

electronics board. These are the connectors you terminated in the

Terminate Wiring

section.

ETC Installation Manual

QuickTouch+ Mk2 Control Panel and Electronics

QuickTouch+ Mk2 Control Panel and Electronics Page 6 of 7 ETC

Terminate Ground Wire

A green and yellow ground wire is attached to the back of the control panel and electrics, with an

insulated quick connect flag on the loose end of the wire. Attach the flag to the ground tab that is

located on the back box to ensure proper grounding of the electronics. The following image

demonstrates where to terminate the ground wire for QT+1 and QT+6/12 Mk2 controllers for both

(A) surface-mount and (B) flush-mount back boxes.

QT+ Mk2 1Ch

QT+ Mk2 6Ch/12Ch

ETC Installation Manual

QuickTouch+ Mk2 Control Panel and Electronics

QuickTouch+ Mk2 Control Panel and Electronics Page 7 of 7 ETC

Secure in Back Box

With all of the wiring terminations complete, secure the control panel in the back box.

Surface-Mount

Place the electronics inside the back box and line up the screw holes in the control panel with the

screw troughs in the back box. Scure the panel to the back box using the screws provided.

Flush-Mount

1. Remove the trim plate and screws while holding the control panel and electronics.

2. Place the trim plate between the control panel and the back box.

3. Align the screw holes for the control panel, trim plate, and mounting rails that are inside the

back box.

4. Secure the control panel and trim plate to the mounting rails using the appropriate size

screws (long and short are provided).

For current and complete compliance information, view the product datasheets at

etcconnect.com. For complete product documentation, including compliance documentation, visit

etcconnect.com/products.

Andere Handbücher für QuickTouch+ Mk2

Inhaltsverzeichnis

Andere ETC Bedienfeld Handbücher

ETC

ETC transtechnik FDX2000 Bedienungsanleitung

ETC

ETC echoflex Elaho Preset Station Bedienungsanleitung

ETC

ETC Echo Control Series Bedienungsanleitung

ETC

ETC SmartFade Bedienungsanleitung

ETC

ETC Ion Xe Bedienungsanleitung

ETC

ETC ColorSource ThruPower Bedienungsanleitung

ETC

ETC SmartFade ML Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten

Truma

Truma CP plus Bedienungsanleitung