ETC Net3 Four Port Gateway Bedienungsanleitung

Product information and specifications subject to change.

Part Number: 4260M2200 Rev C

Released: 2009-03

Four Port Gateway

Setup Guide

Revision C

Net3™

ETC permits the reproduction of materials in this manual only for non-commercial purposes. All other rights are

reserved by ETC.

Table of Contents

ETC

, Eos™, Congo™, Emphasis

, Obsession

II, ETCNet2™, EDMX™, Sensor

, Unison

, Light Manager™,

SmartFade™, SmartSwitch™, SmartBar™, and SmartModule™ are either registered trademarks or trademarks of

Electronic Theatre Controls, Inc. in the United States and other countries. All other trademarks, both marked and

not marked, are the property of their respective owners.

Introduction. . . . . . . . . . . . . . . . . . . . . . 1

Listen to What Our Customers Want. . . . . . . . . . . . . . . . . . . . . . . .1

Give Them More Than They Expect . . . . . . . . . . . . . . . . . . . . . . . .1

Using this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Help from ETC Technical Services . . . . . . . . . . . . . . . . . . . . . . . . .2

Section 1: Gateway Hardware . . . . . . . . . . . . . . . . . . . 3

Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Rear Panel Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Section 2: DMX Gateway Modules . . . . . . . . . . . . . . . 4

Module Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

DMX Basics & Pin-outs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

RDM Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Under the Module Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Section 3: Rack Mount Kit-4260K1001 (optional) . . . . 8

Section 4: DMX Front Panel Kits (optional) . . . . . . . . . 9

Section 5: Hanging Hardware Kit (optional). . . . . . . . 10

Section 6: International Power Supply Kit (optional) . 11

Appendix A: Specifications . . . . . . . . . . . . . . . . . . . . . . 13

Net3 Four Port Gateway Control Features . . . . . . . . . . . . . . . . . . 13

Net3 Four Port Gateway Specification . . . . . . . . . . . . . . . . . . . . . 13

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

1Net3 Four Port Gateway Setup Guide

Introduction

Congratulations on your purchase of an industry leading ETC Net3™ network device.

This manual will guide you through the setup of the hardware, electrical and data

connections of this Gateway. It does not cover any of the software modes and

configuration. This is covered separately by specific tied to the software versions that may

be running in these Gateways, such as the ETCNet2 NCE v4.1 User Manual which has

been updated to include information about the Net3 DMX Gateways running in ETCNet2

mode.

Listen to What Our Customers Want

If you are already familiar with our line of ETCNet2 DMX Nodes, you will notice some

significant changes to our new DMX Gateways. Many of these changes are a direct result

from customer feedback.

•Smaller size. The compact design of the unit now allows it to go in more places and

provides you with the ability of getting more DMX ports per rack space. This is still only

1U rack space tall, but now 1/2 rack space wide.

•LCD Display. The LCD replaces the LEDs on the ETCNet2 nodes and provides a

wealth more information about status, configuration and the software that is currently

active in the Gateway.

•Supports PoE standard IEEE 802.3af (Power over Ethernet). In addition to

supporting external DC power supplies, the Net3 Gateways now also support PoE to

ease installation and reduce the need for having AC power nearby.

Give Them More Than They Expect

•Modular DMX port design. The modular port design represents a major leap forward

in flexible configuration and serviceability via module repair and replacement. While it’s

never good when a device encounters a problem, the Net3 DMX Gateway provides a

very easy path to being up and working again with a minimal amount of fuss by putting

the electronics most commonly zapped by outside equipment in the individual modules

for easy service and/or replacement.

Using this Manual

In order to be specific about where features and commands are found, the following naming

and text conventions will be used throughout this manual:

• References to other parts of the quick guide are indicated in italics. When viewing this

setup guide electronically, click on the reference to jump to that section in the

document.

Note:

Notes are helpful hints and information that is supplemental to the main text.

Please email comments about this manual to: TechComm@etcconnect.com

Help from ETC Technical Services

If you are having difficulties, your most convenient resources are provided in this user

manual. To search more widely, try the ETC website at www.etcconnect.com. If none of

these resources is sufficient, contact ETC Technical Services directly at one of the offices

identified below.

CAUTION:

Caution statement indicates situations where there may be undefined or

unwanted consequences of an action, potential for data loss or an equipment

problem.

CAUTION:

Caution statement indicates situations where ESD (Electro-Static Discharge) may

damage equipment. Special precautions should be taken to keep your self

grounded to avoid damaging the equipment.

WARNING:

A Warning statement indicates situations where damage may occur, people

may be harmed, or there are serious or dangerous consequences of an

action.

WARNING:

RISK OF ELECTRIC SHOCK! This warning statement indicates situations

where there is a risk of electric shock.

Americas United Kingdom

Electronic Theatre Controls Inc. Electronic Theatre Controls Ltd.

Technical Services Department Technical Services Department

3031 Pleasant View Road 26-28 Victoria Industrial Estate

Middleton, WI 53562 Victoria Road,

800-775-4382 (USA, toll-free) London W3 6UU England

+1-608 831-4116 +44 (0)20 8896 1000

[email protected] se[email protected]

Asia Germany

Electronic Theatre Controls Asia, Ltd. Electronic Theatre Controls GmbH

Technical Services Department Technical Services Department

Room 1801, 18/F Ohmstrasse 3

Tower 1, Phase 1, Enterprise Square 83607 Holzkirchen, Germany

9 Sheung Yuet Road +49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong [email protected]

+852 2799 1220

[email protected]

3Net3 Four Port Gateway Setup Guide

Section 1:

Gateway Hardware

Front Panel Layout

Rear Panel Layout

Push

Ethernet connection supports:

• EtherCon™ locking connector

• PoE (IEEE 802.3af)

• 10/100Mbps data speeds

• Auto-sensing

• Auto-negotiation.

Reset button to hard

reboot the Gateway

(this button is recessed)

The LCD button activates the

backlight (depending on the

mode) as well as advances

through display pages

LCD display. The exact content changes by mode

and software version but generally contains

information about status, configuration and the

software that is currently active in the Gateway

Blue LED

• On indicates power

Green LED

• On indicates network connection

• Flashing indicates network activity

Blank plate

Blue LED

• On indicates power

Green LED

• On indicates network connection

• Flashing indicates network activity

Four module bays (each

with a retaining screw)

DMX Out (XLR Fem)

module

DMX In (XLR Male)

module

Terminal strip module

DC power input

• 8-28Vdc

• Positive tip

• 3.5mm barrel

• 5 watts usage

The modules shown are to illustrate the different types available.

Port #1 Port #2 Port #3 Port #4

Strain relief clip for

dc power cable

Grounding

post

DMX Gateway Modules 4

Section 2:

DMX Gateway Modules

There are four different types of modules available: DMX Out (XLR 5-pin female), DMX In

(XLR 5-pin male), DMX RJ45 (RJ45 8-pin female) and DMX terminal strip.

The Terminal Strip Module comes with ETC’s standard DMX termination preparation kit

(ETC Part # 4100A1012). This kit includes instructions, a screw terminal connector and

heat shrink.

The DMX RJ45 module can use a standard Cat5 cable to transmit DMX512 to other devices

with the same connector. The DMX RJ45 module will not function as an Ethernet

network port.

Any of these modules can be configured via software to be either a DMX input or a DMX

output.

Additionally, there is a blanking plate that is installed to cover the module bay in the

absence of a module (depending on how the Gateway is configured, not all module bays

will have a module installed in it).

With power removed from the Gateway, you can move and swap DMX modules as needed

for desired configuration or replacement.

Module Hardware

WARNING:

RISK OF ELECTRIC SHOCK! Power must be removed from the Gateway

before removing any modules or covers to service the unit.

Retaining screw to keep the

modules secure in the Gateway

Pull-tab for easy module removal

DMX Termination switch directly

behind the connector

DMX Out Module

(XLR 5-pin female)

DMX In Module

(XLR 5-pin male)

DMX Terminal

Strip Module

(8-pin male)

DMX RJ45 Module

(RJ45 8-pin female)

Protective cover over more

delicate electronics

5Net3 Four Port Gateway Setup Guide

DMX Basics & Pin-outs

The Net3 Four Port Gateway sends and receives DMX 512 control signal. The unit is can

contain a 5-pin XLR DMX input connector, a 5-pin XLR DMX output connector or a terminal

strip connector. DMX cables should be acceptable for DMX data transmission (not

microphone cable) and should follow the standard pinout. The optional secondary data pair

is not used by the Net3 Four Port Gateway.

The DMX network supports up to 32 devices connected to each DMX line. Termination is

required for all DMX networks and belongs at the beginning (source) of a DMX network and

with the last device physically connected device in the chain.

A compact switch (S1) located behind the DMX connector on each module is provided to

enable and disable DMX termination. These switches are defaulted to on for every module.

The most common reason to disable this termination is if you wanted to do a “touch and go”

connection on a terminal strip module. “Touch and go” means that you land DMX wiring on

the connector for the module, and continue to another DMX device.

DMX512 Pinout for five-pin XLR Connectors

Female Pin# Use Male

1 Common (Shield)

2Data–

3Data+

4 not connected

5 not connected

DMX512 Pinout for Terminal Strip Connectors

Male Pin# Use Wire Color

1 Common (Shield) Clear/Shield

2Data– Black

3 Data + Red

4 not connected

5 not connected

6 not connected

7 not connected

8 not connected

DMX512 Pinout for RJ45 Connectors

Female Pin# Use Wire Color

1 Data 1 + White/Orange

2 Data 1 – Orange

3 not connected White/Green

4 not connected Blue

5 not connected While/Blue

6 not connected Green

7 Signal Common White/Brown

8 Signal Common Brown

Push

DMX Gateway Modules 6

RDM Basics

Net3 Gateway software now supports Remote Device Management (RDM) protocol. By

default, RDM is not enabled on Net3 Gateways. To enable RDM on the Net3 Gateway,

Net3 Gateway Configuration Editor (GCE) is required. Please see the GCE help files for

more information on activating RDM on your Net3 Gateways.

About RDM

Remote Device Management (RDM) is a protocol enhancement to DMX512 that allows

bi-directional communication between a lighting system controller and attached

RDM-compliant responder devices over a standard DMX line. This protocol allows

configuration, status monitoring, and management of these devices.

An RDM Controller is the device that initiates communication with one or more RDM

Responder devices. Examples of controllers are ETC's Net3 DMX/RDM 2-Port and 4-Port

Gateways and RDM-enabled consoles.

An RDM Responder is the device that replies to communication from a controller. Examples

of responders are RDM-enabled edge devices such as gel scrollers, dimmers, and moving

lights.

Net3 DMX/RDM Gateways support 32 RDM devices per port, just like DMX devices.

Compliant DMX512 and DMX512-A devices (non-RDM devices) are completely functional

when RDM is present.

RDM was developed by the ESTA Technical Standards and can be referenced as ANSI/

ESTA E1.20.

7Net3 Four Port Gateway Setup Guide

Under the Module Cover

Here is a small bit of service information for you if you are technically inclined. There is an

assumed level of knowledge that goes with the information being provided (i.e. how to pull

an IC chip without bending the pins and how to work around delicate electronics).

If for any reason you don’t feel comfortable working around delicate electronics (it’s not for

everyone), then you should contact your local ETC dealer or ETC office for service and

support options. ETC office contact information can be found in Help from ETC Technical

Services on page 2.

One of the most common issues a DMX device can encounter is an electrical surge/spike

that comes down the line and “pop” or burn out the DMX transceiver chip. Under the

module’s cover, each of the modules contain a socketed DMX transceiver chip for easy

replacement.

This DMX transceiver chip is a 75LBC182 (ETC Part # Z1458). For those of you familiar

with ETC’s other products, you may expect a 75176 chip here. The 75LBC182 is a more

robust chip that can withstand electrical spikes better than the 75176. However, the

75LBC182 is pin-compatible with the 75176 so either may be used in an emergency.

CAUTION:

Special precautions should be taken to keep yourself grounded to avoid damaging

the equipment. ESD (Electro-Static Discharge) may damage the module’s

electronics.

Inhaltsverzeichnis

Andere ETC Tor Handbücher

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC DMX/RDM One Port Gateway Bedienungsanleitung

ETC

ETC NET 3 Bedienungsanleitung

ETC

ETC Response Analog IO Gateway Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC Response Stücklistenhandbuch

ETC

ETC Response Mk2 One-Port Bedienungsanleitung

ETC

ETC Response Bedienungsanleitung

ETC

ETC NET 3 Bedienungsanleitung

ETC

ETC Response Mk2 One-Port Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC Response SMPTE Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC Net3 Conductor Bedienungsanleitung

ETC

ETC VG-5000 Bedienungsanleitung

ETC

ETC Response MIDI Gateway Bedienungsanleitung

ETC

ETC Response Bedienungsanleitung

ETC

ETC Response Mk2 One-Port Bedienungsanleitung

ETC

ETC NET 3 Bedienungsanleitung

ETC

ETC Net 3 Bedienungsanleitung

ETC

ETC Response Mk2 One-Port Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung